Related Manuals for VENCO VC620
Summary of Contents for VENCO VC620
- Page 3 TABLE OF CONTENTS VC 520 MANUAL PAGE DESCRIPTION REF. NO. READ THIS FIRST ..................416733 IMPORTANT WARNING................416086 WARNING AND CAUTION DECAL LOCATIONS ........416128 DECAL DRAWINGS & LIST ................ 628820 VC 520 (NON-SUBFRAME) CAPACITIES............. 520601 VC 520 (WITH SUBFRAME) CAPACITIES............ 520602 VC 520 MOUNTING DIMENSIONS...............
-
Page 4: Read This First
VC520 W/ SUBFRAME - 520602 VC620 NON SUBFRAME - 620103 VC620 W/ SUBFRAME - 620104 VC628 - 628020 VC5520 - 552010 VC6620 - 662052 VC6628 - 662851 4. USE PUMP WHICH MEETS VENCO SPECIFICATION SEE PAGE: 416763. TITLE DATE SECTION CAUTION NOTE 1-22-08A MANUFACTURING, INC. - Page 6 Included with your Venco Hoist are various warning, danger, and caution decals. These decals must be placed in prominent locations so they are easily seen and readily identifiable; this illustration provides the recommended decal locations. DATE SECTION TITLE 9-22-09D DECAL LOCATIONS H100 MANUFACTURING, INC.
- Page 11 HOIST MOUNTING INSTRUCTIONS (VC 520 NON-SUBFRAME ONLY) Refer to drawings 520601 or 520603 (on the preceding pages). CAUTION If the distance between the center of the rear axle and the rear hinge assembly exceeds 38", additional reinforcement of the truck frame is necessary. A.
- Page 12 HOIST MOUNTING INSTRUCTIONS (VC 520 / 620 NON-SUBFRAME ONLY) E. After the hoist is positioned, place the mounting angles (Figure 3) under the lower pivot angles and against the truck frame. Clamp securely in place. Drill though the frame and install the mounting angle with two (2) 1/2" x 1-1/2"...
- Page 14 HOIST MOUNTING INSTRUCTIONS (VC 520 / 620 WITH SUBFRAME ONLY) Refer to drawing 520602 for VC 520 and 620104 for VC 620 (on the preceding pages). A. Position the hoist into the front half of the subframe by inserting the two lower pivot angles into the lower pivot tube on the scissors and then positioning that assembly inside the front half of the subframe.
- Page 19 NOTE: FOR BI-ROTATIONAL PUMP MOUNTING AND HOSE CONNECTION FAILURE TO MATCH PTO ROTATION WITH PUMP ROTATION WILL INFORMATION, SEE DRAWING 416812. RESULT IN PUMP FAILURE. Model VC416 VC516 VC520 VC620 VC628 VC5520 VC6620 VC6628 620125 - Curved 620124 - Straight Control Cable &...
- Page 21 TITLE DATE SECTION WILLIAMS PTO WARNING 7-13-98 H200 MANUFACTURING, INC. SUPERCEDES 416287...
- Page 22 HOIST MOUNTING INSTRUCTIONS (Continued) I. Position and secure the filler strips (liner or sleeper) to the truck frame. The VC 520 with subframe requires a minimum of 9-1/2" clearance above the truck frame. The VC 520 (non-subframe) requires a minimum of 7-1/2" clearance above the truck frame. Note: If the hoist needs to be mounted higher due to interference between the hoist knuckle and the truck frame, additional clearance above the truck frame will be required.
- Page 24 BODY 6628 ONLY: WELD 662845 PLATE (FURNISHED) REAR HINGE TO INSIDE BODY RAIL BRACKET AND TO HINGE ASSY TUBE WELD HINGE ASSY TUBE TRUCK FRAME (CHASSIS) TITLE DATE SECTION REAR HINGE TO BED MTG. INSTR. 6-28-97A H200 MANUFACTURING, INC. SUPERSEDES 662861 VC 520 - VC 6628 10-23-97...
- Page 29 TRUCK FRAME GROUNDING STRAP #4 GAGE BLACK DATE SECTION TITLE 12-1-04D 416081 ED POWER UNIT MANUFACTURING, INC. SUPERCEDES 416306 VC416/516, VC520/620 2-15-99C...
- Page 30 TRUCK FRAME #4 GAGE BLACK NOTE: ENERGIZING 'G' COIL SENDS FLOW TO 'C1' PORT (HOIST UP) ENERGIZING 'R' COIL SENDS FLOW TO 'C2' PORT (HOIST DOWN) DATE SECTION TITLE 4-20-05F 416081M ED POWER UNIT MANUFACTURING, INC. SUPERCEDES 416307 12-1-04E VC416/516, VC520/620...
- Page 31 4. To lower the hoist, push the pump knob in. NOTE The Venco Hoists powered by PTO drive pumps must be "powered down". Failure to "power down" will cause the reservoir to overflow. 5. To lock the hoist against the truck frame when it is in the down position, push the pump knob in. When the pump bypasses, place the knob in the center "hold"...
- Page 33 BODY PROP USE AND WARNINGS D. Body prop(s): Federal Regulation 1926.601, Paragraph 10, requires the use of a body prop. Accordingly, all Venco Hoist Units will have included as a standard item a body prop (safety strut). See Paragraphs D.1. & D.2. below.
- Page 35 VC 520 WITH SUBFRAME REPLACEMENT PARTS LIST ITEM PART NUMBER DESCRIPTION 520590 SUBFRAME WELDED ASSEMBLY 520588 SUBFRAME EXTENSION KIT (OPTIONAL) 520524-1 LOWER PIVOT ASSEMBLY - RIGHT 520524-2 LOWER PIVOT ASSEMBLY - LEFT 520527 UPPER PIVOT ASSEMBLY 416220 COLLAR - UPPER PIVOT 520063 FRAME MOUNTING ANGLE 520532...
- Page 37 VC 520 (NON-SUBFRAME) REPLACEMENT PARTS LIST ITEM PART NUMBER DESCRIPTION 416220 COLLAR - UPPER & LOWER PIVOTS 520063 FRAME MOUNTING ANGLE 520562 UPPER PIVOT ASSY 520563-1 LOWER PIVOT ASSEMBLY 520563-2 LOWER PIVOT ASSEMBLY 662057 REAR HINGE ASSY !HHCS05013150 HEX HEAD CAP SCREW - 1/2"-13 x 1-1/2" LG. !FWSH-050 FLAT WASHER - 1/2"...
-
Page 39: Replacement Parts List
520503 REPLACEMENT PARTS LIST ITEM PART NUMBER DESCRIPTION 520502 SCISSORS ASSEMBLY 520904 HYDRAULIC CYLINDER !HHCS05013275-8 HEX HEAD CAP SCREW - 1/2"-13 x 2-3/4" LG. GR. 8 !LWSH-050 LOCK WASHER - 1/2" !HNUT-05013 HEX NUT - 1/2"-13 416545 5/8 X 3-1/2 CLEVIS PIN ASSEMBLY REPLACEMENT PARTS DWG REF 520503 TITLE DATE... - Page 44 +2,676 /,0,7(' :$55$17< 32/,&< 7KLV OLPLWHG SROLF\ ZDUUDQWV QHZ SURGXFWV RI 9HQFR WR EH IUHH IURP GHIHFWV LQ PDWHULDO DQG ZRUNPDQVKLS IRU D SHULRG RI WKUHH \HDUV IURP GDWH RI RULJLQDO LQVWDOODWLRQ 7KLV ZDUUDQW\ FRYHUV 5HSDLU RU UHSODFHPHQW RI SURGXFW /DERU WR UHSDLU RU UHSODFH SURGXFW )UHLJKW WR UHWXUQ DQGRU UHSODFH SURGXFW :H VKDOO QRW EH OLDEOH IRU DQ\ FRQWLQJHQW OLDELOLWLHV DULVLQJ RXW RI WKH LPSURSHU IXQFWLRQ RI DQ\ SURGXFWV...
Need help?
Do you have a question about the VC620 and is the answer not in the manual?
Questions and answers