Page 1
(3) Buyer indemnifies cifications stated in the t as specifically set forth ed; and (5) all disputes ornia and the prevailing nable attorney fees and opies of such warranties & Drain, Inc. will obtain s upon request. Gorlitz performing this service.
Page 2
Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This drain cleaner is designed for certain applications only. Gorlitz Sewer & Drain Inc. is not responsible for issues arising from modification or improper use of this product such as an application for which it was not designed.
DO NOT OVERLOAD THE DRAIN CLEANER: THE GO 31 DRAIN CLEANER WILL ONLY DO THE JOB IT WAS DESIGNED FOR. MAINTAIN LABELS: ALL LABELS HAVE IMPORTANT INFORMATION. IF WORN, UNREADABLE OR MISSING, CONTACT GORLITZ SEWER & DRAIN FOR REPLACEMENTS. Gorlitz Operating & Maintenance Manual...
Page 4
WARRANTY. LUBRICATION ALL GORLITZ SEWER AND DRAIN CLEANING MACHINES SHOULD BE GIVEN THE BEST OF CARE. IF KEPT CLEAN AND PROPERLY LUBRICATED, IT WILL PROVIDE MANY YEARS OF TROUBLE-FREE SERVICE. THE FOLLOWING INSTRUCTIONS SHOULD BE CAREFULLY OBSERVED AT ALL TIMES: •...
THE MODEL COMPARISON CHART PICTURED ABOVE SHOULD BE ONLY USED AS A GUIDELINE. ITS SUGGESTED APPLICATION MAY VARY DEPENDING ON SITE OF LOCATION, AGE, BENDS, MATERIAL AND LENGTH OF DRAINAGE PIPE AND OPERATOR. * SEE SEPARATE MANUFACTURER’S OPERATING INSTRUCTIONS FOR MODEL GO 31 HANDYGUN. Gorlitz Operating & Maintenance Manual...
Page 6
WITH MACHINE RUNNING IN ORDER FOR YOUR DRIVE ARM TO DISTRIBUTE CABLE INTO DRUM OR REEL EVENLY. WHEN OPERATING MACHINE WITH A POWER CABLE FEEDER AND PULLER, DO NOT ALLOW ANY CABLE ENDS OR CABLE CONNECTORS TO PASS THROUGH FEEDER AS IT MAY DAMAGE OR BREAK THE FEEDER BEARINGS. Gorlitz Operating & Maintenance Manual...
Page 7
COUPLE CABLES TOGETHER COUPLE CABLES TOGETHER COUPLE CABLES TOGETHER CONTINUE DOWN THE PIPE CONTINUE DOWN THE PIPE CONTINUE DOWN THE PIPE COUPLE CABLES TOGETHER COUPLE CABLES TOGETHER CONTINUE DOWN THE PIPE CONTINUE DOWN THE PIPE Gorlitz Operating & Maintenance Manual...
Page 8
ONLY BY MEANS OF ARC WELDING, SPOTWELD CABLE TO COUPLING. ANY ATTEMPT TO WELD OR BRACE CABLE TO ANY COUPLING WITH AN ACETYLENE TORCH WILL SOFTEN THE FIRST COILS OF CABLE AND THEREBY RENDERING THE CABLE AT THAT POINT USELESS. Gorlitz Operating & Maintenance Manual...
Page 9
INTO DRUM ALLOWING ADEQUATE LENGTH OF EXPOSED CABLE ATTACH FLEXIBLE LEADER (ELEPHANT TRUNK) WHEN APPLICABLE. INSTALL CABLE END AND CUTTING BLADE (AVAILABLE ONLY FOR 3/8” DIA. CABLE) AND/ OR MAKE CABLE BENDS OF YOUR CHOICE. Gorlitz Operating & Maintenance Manual...
Page 10
PULL DRIVE ARM OUT OF FRONT BEARING. CABLE IS ALWAYS UNDER TENSION. DO NOT LET CABLE FLY OUT OF CAGE. WHEN INSTALLING REEL, REVERSE PROCEDURE. BE POSITIVE DRIVE PLATE ENGAGE PROPERLY INTO BACK OF REEL. Gorlitz Operating & Maintenance Manual...
Page 11
BEFORE SEPARATING DRUM PULL OUT ENTIRE CABLE. REMOVE 4 SMALL SCREWS AND PULL DRUM SECTIONS APART. WHEN INSTALLING DRUM, REVERSE PROCESS. MAKE CERTAIN SET SCREW ENGAGES FLAT AREA ON DRIVE SHAFT. HOW TO ASSEMBLE CHUCK AND CUTTING TOOLS Gorlitz Operating & Maintenance Manual...
Page 12
When energized by actuation of the reset button, it will conveniently supply power to any power tool or appliance whose power requirement does not exceed 20 amperes at 120 volts RMS, 60 Hertz or 2400 watts. Gorlitz Operating & Maintenance Manual...
GENERAL MAINTENANCE TIPS TO KEEP YOUR GORLITZ ELECTRIC SEWER CLEANING MACHINES IN GOOD, CLEAN AND SAFE OPERATING CONDITION, PERIODICALLY CHECK THE FOLLOWING PARTS: • LUBRICATE ALL SLIDING, ROTATING AND MOVING PARTS. • PAY SPECIAL ATTENTION TO WEARS ON DRIVE ARMS.
IF THE CABLE BEGINS TO SLIP OR DOES NOT FEED, THE HAND KNOB MAY BE TIGHTENED WITH CAUTION UNTIL CABLE IS MOVING AGAIN. EXTREME TIGHTENING OF HAND KNOB ASSEMBLY MAY DAMAGE POWER FEEDER BEARING, OVERLOAD MOTOR AND/OR ADD EXCESSIVE TENTION TO CABLE. Gorlitz Operating & Maintenance Manual...
Page 15
POSITION TO RETRACT CABLE INTO REEL OR DRUM. LUBRICATION THE GORLITZ POWER CABLE FEEDER AND PULLER SHOULD BE GIVEN THE BEST OF CARE AND IF KEPT CLEAN AND PROPERLY LUBRICATED, IT WILL PROVIDE MANY YEARS OF TROUBLE-FREE SERVICE. OBSERVE THE FOLLOWING INSTRUCTIONS AT ALL TIMES: •...
Page 24
PART # DESCRIPTION PART # DESCRIPTION T 05A WINCH REPL. SWITCH* T 05E FUSE* T 05C R/C TOGGLE SWITCH* T 05F WINCH CRANK* T 05D R/C TOGGLE SWITCH ASSEMBLY* T 05G CABLE AND HOOK ASSEMBLY* Gorlitz Operating & Maintenance Manual...
Page 25
The technician knows that continual rotation in the reverse position may cause the cable to exit the machine rapidly resulting in possible injury. A machine with an automatic feed can feed the cable in and out Gorlitz Operating & Maintenance Manual...
Page 26
Printed with permission by Spartan Tool, a division of Pettibone Corporation. Copyright 1992 You can purchase The Professional Handbook-Drain and Sewer Cleaners at our website: https://www.gorlitz.com/drain-cleaning-machines/Handbook.asp Gorlitz Operating & Maintenance Manual...
Page 27
Please refer back to Hubbell & Leviton GFCI Operating & Testing Instructions on page 11. NOTE Gorlitz Operating & Maintenance Manual...
Page 28
(1) year from date of purchase to original buyer. If any parts break or fail, we ask you to notify your nearest dealer or Gorlitz Sewer & Drain, Inc. and supply us with proof of purchase and nature of failure.
Need help?
Do you have a question about the GO 50 Series and is the answer not in the manual?
Questions and answers