Erasing One Of The Remote Control Button; Settings; Resetting The Remote Control Presets; Confirming Preset Codes - Pioneer VSX9120TXHK - 770w 7.1 Channel Dolby Truehd Operating Instructions Manual

Controlling the rest of your system
11
• The remote controls should be 3 cm to 5 cm (1 to 2
inches) apart.
5 Press the corresponding button on the other
remote control that is sending (teaching) the signal to
this receiver's remote control.
For example, if you want to learn the playback control
signal, press and hold
show OK if the operation has been learned.
If for some reasons the operation hasn't been learned the
LCD will display ERROR briefly and then display PRES
KEY again. If this happens, keep pressing the (teaching)
button as you vary the distance between the two remotes,
until the LCD display shows OK.
Certain buttons represent operations that cannot be
learned from other remote controls.
available are shown below (with the exception of the TV
controls, a combination of SHIFT and these buttons can
also be learned):
RECEIVER
INPUT
SELECT
XM RADIO SIRIUS
DVD TV
CD-R/TAPE HDMI 2
iPod HDMI 1
SLEEP
SR+
DIALOG E
D.ACCESS
+10
AV PARAMETER
TOP MENU
TUNE
ST
SETUP
TUNE
GUIDE
6 To program additional signals for the current
component repeat steps 4 and 5.
To program signals for another component, exit and
repeat steps 1 through 5.
7 Press and hold the RECEIVER button for a couple of
seconds to exit and store the operation(s).
Note
1 Note that interference from TVs or other devices will sometimes result in the remote control learning the wrong signal.
2 • Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or farther apart.
• If the remote LCD shows FULL, it means the memory is full. See Erasing one of the remote control button settings below to erase a programmed button
you're not using to free up more memory (note that some signals may take more memory than others).
3 Note that the number key decimal button (+10/D.ACCESS) may not be learned with some components.
68
En
3 cm to 5 cm
(1 to 2 inches)
briefly. The LCD display will
2
3
The buttons
SYSTEM OFF
SOURCE
TV CONTROL
INPUT
TV VOL TV CH VOL
SELECT
DVR 2
DVR 1 TV CTRL
CD ZONE 2
ANT REC INFO
TUNER RECEIVER
MUTE
MPX REC STOP JUKEBOX
S.RETRIEVER ANALOG
ATT
AUDIO SUBTITLE HDD DVD
DIMMER MIDNIGHT/
DISP CH CH
LOUDNESS
PHOTO
STEREO/
STATUS SIGNAL SEL SB ch
F.S.SURR
MULTI OPE THX STANDARD ADV.SURR
CLASS
DISC
ENTER
SHIFT PHASE
MCACC S.DIRECT
CH LEVEL
MENU
ST T.EDIT
ENTER
RETURN
RECEIVER
BAND
Erasing one of the remote control
button settings
This erases one of the buttons you have programmed and
restores the button to the factory default.
1 While pressing the RECEIVER button, press SETUP .
The remote LCD display shows SETUP.
2 Use
The LCD on the remote prompts you for the component
corresponding to the button setting to be erased.
1
3 Press the input source button corresponding to the
command to be erased then press ENTER .
The LCD display flashes PRES KEY.
4 Press and hold the button to be erased for two
seconds.
The LCD display shows OK or NO CODE to confirm the
button has been erased.
5 Repeat step 4 to erase other buttons.
6 Press and hold the RECEIVER button for a couple of
seconds when you're done.

Resetting the remote control presets

This will erase all preset remote control preset codes and
programmed buttons.
1 While pressing the RECEIVER button, press SETUP .
The remote LCD display shows SETUP.
2 Use
RESET flashes in the LCD display.
3 Press and hold ENTER for about two seconds .
The LCD shows OK to confirm the remote presets have
been erased.

Confirming preset codes

Use this feature to check which preset code is assigned
to an input source button.
1 While pressing the RECEIVER button, press SETUP .
The remote LCD display shows SETUP.
2 Use
The LCD on the remote prompts you for the input source
button you want to check.
to select ERASE then press ENTER .
to select RESET then press ENTER .
to select READ ID then press ENTER .