Related Manuals for Solutions ORS-2066R
Summarization of Contents
IMPORTANT LABELS AND INDICATORS
Indicators and Unit Ratings
Details unit indicators, power status, serial number, and technical ratings.
Critical Safety Warnings
Covers DANGER, CAUTION, and WARNING statements on flammability, electrical hazards, and fire risk.
Operational Guidelines and Precautions
Grounding Reliability Note
Ensuring grounding reliability requires connection to a 'Hospital Only' or 'Hospital Grade' receptacle.
Power On Caution
Caution to keep power OFF until the minimum fluid level is poured into the drape.
TEMPERATURE CONTROLS
Upper Indicator (PV - Present Value)
Displays the current temperature of the solution.
Lower Indicator (SV - Set Value)
Indicates the target temperature to which the solution is set.
AL Indicator
Lights up when the present value is 4°F higher than the set value.
Fahrenheit (°F) Readout
Confirms that temperature readouts are displayed in Fahrenheit.
SP1 Indicator
Illuminates when the heating element is actively warming the solution.
SP2 Indicator
Notes that the SP2 indicator is not applicable for this unit.
Temperature Setting Arrows
Up/down arrows used to adjust the temperature setting (Set Value).
OPERATING INSTRUCTIONS
Draping the Warmer
Instructions for draping the solution warmer and ensuring the power switch is off.
Pouring Solution
Procedure for pouring solution into the drape, maintaining minimum fluid requirements.
Drape Adjustment
Ensuring uniform contact of the drape with basin walls, avoiding air pockets.
Turning Machine On
Instructions to depress the POWER switch to turn the machine on.
Selecting Temperature
Steps to press index, adjust set temperature with arrows, and press enter.
Turning Machine Off
Procedure for turning the machine off using the POWER switch, not unplugging.
Discarding Solution and Drape
Guidelines for discarding used solution and drapes according to hospital procedures.
Critical Operating Notes
Important notes: never turn on before minimum fluid, do not unplug until power is off, use with approved drapes.
MAINTENANCE
Care of Solution Warmer After Each Use
Cleaning with lint-free cloth and isopropyl alcohol to prevent corrosion.
Basin Scrubbing
Scrubbing the basin monthly with a non-abrasive cleanser to prevent corrosion.
Power Cord and Plug Inspection
Inspecting power cord and plug for wear or abuse and contacting ORS for repairs.
Temperature Controller Verification
Procedure for verifying temperature controller accuracy every five years using specific equipment.
Temperature Verification Procedure
Steps for filling basin, setting temperature, and using a thermometer to check accuracy.
WARRANTY
Warranty Coverage
One-year warranty against defects in workmanship and materials; ORS may repair or replace.
Warranty Disclaimer
Disclaimer of all other warranties (express or implied) and limitation of liability for damages.
TROUBLESHOOTING
Corrosion in Basin
Solution: Scrub basin with a non-abrasive cleanser to remove corrosion.
Power Switch Not Lit
Check plug, outlet, and inspect cord for wear. Contact ORS if issue persists.
Unit Not Heating Up
Check LED display, temperature adjustment, and contact ORS if still not heating.
Temperature Not Reaching Set Point
Verify temperature adjustment and check drape distribution for proper contact.
Unusual Temperature Fluctuations
Ensure drape is evenly distributed and in full contact with basin walls.
Water Remaining in Basin After Use
Normal due to condensation; dry with lint-free cloth and isopropyl alcohol.
General Operation Problem
Warning: If the Solution Warmer does not operate properly, contact ORS.
SPECIFICATIONS
Power and Fuse Specifications
Details on power requirements (115/230 VAC) and fuse type (3A Slo-Blo).
Temperature Range and Variance
Specifies normal temperature range (room to 120°F) and variance (+/-2°F).
Temperature Control System
Describes the microprocessor controller with LED readout for temperature and set point.
Model Capacities and Bowl Dimensions
Lists various ORS-2000 models with their capacities and bowl dimensions.
Unit Diagram
Illustrates the physical layout of the warmer, showing power switch and controls.
MOUNTING INSTRUCTIONS
Assembly with ORS-S21/S22 Stand
Instructions for assembling the warmer with specific stands using machine screws.
Mounting to Slush Machine
Procedure for mounting the ORS-2038 warmer to the ORS-1075HS Slush Machine.
Need help?
Do you have a question about the ORS-2066R and is the answer not in the manual?
Questions and answers