Table of Contents Page Preface and terms of warranty Approval plate Installation and connection -Installation -Water connection -Drain connection -Electrical connection/survey of supply lines Exhaust Checking before use Annual service check 12-13 Start menu Main menu 15-61 Set-up menu 16-22 -Select language -Network 18-19...
Preface and Terms of Warranty You are now the owner of one of the leading oven products on the market. All HOUNÖ products are currently subjected to intensive product development, which ensures that the products always contain the latest technology and the most up-to-date and energy- saving methods of preparation.
Approval Plate When communicating with HOUNÖ, we kindly ask you inform us of the serial number of the oven that is stated on the approval plate. The approval plate is usually located on the oven cabinet, behind the oven door, as shown below. The HOUNÖ...
Installation and Connection Unpacking the oven The oven is best handled while still in its wrapping. Wherever possible, use a lifting trolley. Introduce the lifting trolley under the lower cross tube of the stand and place a couple of wooden blocks between the cross tube and the lifting trolley. To achieve the best possible balance, introduce the lifting trolley from the front of the oven or from the motor side.
Installation and Connection Installing the oven To ensure that the oven functions correctly when installed, it should be placed upright and level (horizontally). This is measured at the front and side edge of the roof, and adjustment is made by means of the adjusting screws on the stand or on the legs of table models. The height of the oven can also be adjusted to fit the trolley for rack.
Water connection HOUNÖ ovens have one or two water connections. To facilitate cleaning and service, the oven should be connected with an approved flexible ½” hose and the permanent installations should be fitted with a stop-tap and a non-return valve. Before connecting the oven to water, flush the tubes thoroughly.
Installation and Connection Drain connection From the factory, the HOUNÖ ovens are equipped with a drain system that removes surplus water from the oven chamber. This water may be condensed water from the products, or it may occur when the oven chamber is cooled down with cold water, or when the oven chamber is cleaned.
Installation and Connection Electrical connection/survey of supply lines The electrical connection must be carried out by an authorised electrician in accordance with existing rules and regulations. The wiring diagram is located in the motor compartment. The terminal for the electrical connection is located behind the right side plate. An approved plug outlet or a safety cutout must be located close to the oven so that the oven can be disconnected during installation and repair.
Exhaust The HOUNÖ ovens are equipped with an open/direct exhaust system that removes surplus humidity from the oven chamber. The exhaust system has an electrically operated damper. The exhaust tube can be connected to a ventilating system. In that case, a special extraction funnel is fitted to avoid suction directly from the oven chamber.
Checking before Use The oven should be checked before you start using it. On the outside Check that the oven has not been damaged in transit (dents, scratches, etc.) • Check/adjust the height and check that the oven is placed level (horizontally) •...
Annual Service Check Customer: Address: Postal code: Serial No of the oven: Model: 1. Connection: Functioning correctly? YES NO Water connection – dirt filter (may need tightening) Electrical connection (may need tightening) Drain connection (May need tightening) Positioning of oven 2.
Page 13
6. Steam generator: Functioning correctly? YES NO Heating elements (check for leaks) Load distribution on phases Level sensor – to be cleaned Drain pump May need descaling 7. Functional test: Components (use test function) Core temperature probe Operation modes CombiWash Service Engineer: Date and signature - 13 -...
Start Menu Main switch Access to main menu (see Not active in HOT AIR p. 15) Chooses next function to Chooses next function to the left (see user’s the right (see user’s manual) manual) Temperature down Temperature up Time up Time down (for operation without time setting, press key until "-:--"...
Main Menu Main switch Return to start screen Not active See user’s manual Access to oven set-up menu (see p. 16) See user’s manual Access to service menu (see p. 23) See user’s manual Not active See user’s manual Not active Not active Access to type in code (see p.
Set-up Menu Main switch Return to main menu Not active Access to SETTING Access to SETTING ALARM CONTRAST in display (see (see p. 20) p. 23) Access to SELECTING Access to SETTING CLOCK LANGUAGE (see p. 17) (see p. 21) Access to NETWORK (see p.
Select Language Main switch Return to SET-UP MENU Access to more languages Selecting Danish Selecting Icelandic Selecting English Selecting Estonian Selecting Swedish Selecting German Selecting Italian Selecting Spanish Selecting French Selecting Finnish Showing the languages available. The red square indicates which language has been •...
Network Main switch Confirmation of setting and Return to SET-UP MENU return to SET-UP MENU Not active Not active Not active Not active Not active Not active Move cursor to the right Move cursor to the left Number down Number up IP addr: Use Not active IP address that is compatible with the network in question.
Page 19
Example of network + oven INTERNET IP address from internet supplier Router 192.168.1.254/24 192.168.1.1/24 192.168.1.2/24 192.168.1.3/24 192.168.1.4/24 192.168.1.5/24 IP / 24 = IP / 255.255.255.0 Network set-up for oven: IP addr: 192.168.1.5 Netmask: 255.255.255.0 Gateway: 192.168.1.254 Access code for CombiNet: USER: Superuser Access code: 87 64 12 Example of direct connection to computer...
Setting Sound Main switch Return to SET-UP MENU Confirmation of setting and return to SET-UP MENU Volume down Volume up Sound frequency down Sound frequency up Testing sound Not active Not active Not active Not active Not active - 20 -...
Setting Clock Main switch Confirmation of setting and Return to SET-UP MENU return to SET-UP MENU Not active Not active Not active Not active Move cursor to the right Move cursor to the left Day/month/year/hours/ Day/month/year/hours/ minutes down minutes up Not active Not active - 21 -...
Oven Set-up Main switch Confirm setting, oven Return to SET-UP MENU starts automatically Not active Moving one menu up Not active Moving one line up Not active Moving one line down Not active Moving one menu down Changing status Changing status With a code for the computer, the service engineer has the option of many settings.
Service Menu Main switch Not active Return to MAIN MENU Access to USB key (see p. Lime-scale diagnosis (see 24-28) p. 34-35) Not active Software update(see p. 36-39) Not active ClimaOptima calibration (see p. 40) Energy counter (see p. 29) Door-sensor calibration (see p.
Select USB Key Service Main switch Not active Return to SERVICE MENU Take backup Retrieve recipes from USB (see user’s manual) Access to restore from Send recipes to USB (see backup (see p. 27) user’s manual) Not active Access to USB key service (see p.
Restore Backup Main switch Select Oven backup and Return to SERVICE MENU proceed to SELECT BACKUP MENU (see p. 26) Not active One line up Not active Not active Not active Not active Not active Not active Ej aktiv One line down In this menu, you select the oven backup to restore from.
Select Backup Menu Main switch Select backup and proceed Return to OVEN MENU to RESTORE FROM BACKUP (see p. 27) Not active One line up Not active Not active Not active Not active Not active Not active Not active One line down In this menu, you select the backup to restore from.
Page 27
Restore from Backup Menu Main switch Return to SELECT BACKUP Start restoring features MENU selected and restart when completed. Not active Select recipes when restoring from backup Not active Select counters when restoring from backup Not active Select error log when restoring from backup Not active Select set-up when...
USB Key Service Menu Main switch Not active Return to SERVICE MENU Not active Not active Not active Not active Not active Not active Not active Not active Select Test key Select Delete key This menu is a survey of the contents of the USB memory key. •...
Energy Counters Main switch Not active Return to SERVICE MENU Not active Not active INFO: Shows oven’s total INFO: Shows oven’s total power consumption since power consumption since last resetting (trip counter) last resetting (counter total) Not active Not active INFO: Shows time of last INFO: Shows time of last resetting of counter total...
Reading Counters Main switch Not active Return to SERVICE MENU Access to error log Not active (see p. 31) Access to error statistics Not active (see p. 32) Not active Access to service counters (see p. 33) Not activ Not active Not active Not active Reading of various counters (units, consumption, errors).
Error Log Main switch Move to next page Return to READING COUNTERS Not active Not active Not active Not active Not active Not active Ej aktiv Not active Ej aktiv Not active This menu shows the last 30 errors that have occurred, the most recent one at the top. •...
Error Statistics 3-20 Main switch Next page Return to READ COUNTERS Not active Not active Not active Not active Not active Not active Not active Not active Resetting of error statistics INFO: Shows time of last resetting This menu shows the number of times the various errors have occurred, and the time of •...
Service Counters Main switch Not active Return to READ COUNTERS Not active Not active Not active Not active Not active Not active Not active Not active Resetting of all counters INFO: Shows time of last resetting ACT: Shows how many times the unit in question has been active. TIME: Shows for how long the unit in question has been active.
Lime-scale Diagnosis Main switch Not active Return to SERVICE MENU Not active Not active Not active Not active INFO: This bar shows the level of lime-scale from 0 to 100%. Not active Not active Start descaling of steam generator Not active Not active Not active Do not interrupt the descaling process.
Page 35
Lime-Scale Diagnosis – Description of steps Step 1 of 14 Emptying (40 sec.), filling, heating to 40°C Step 2 of 14 Display shows: „Remove exhaust valve and add HOUNÖ descaling agent by means of HOUNÖ descaling funnel“ Alarm sounds for 5 sec. Press OK Step 3 of 14 Display shows:...
Software Updating Menu Main switch Not active Return to SERVICE MENU INFO: Shows current Not active software and IO board version and oven serial no Select HOUNÖ server for Not active updating (see p. 37) Not active Select USB key for updating (see p.
Page 37
HOUNÖ Server, Software Updating Menu Main switch Not active Return to SOFTWARE UPDATING MENU INFO: Software installed in Not active oven Not active INFO: Software accessible Not active via FTP server Not active Not active Select Update Only visible if more recent version is available Not active Not active...
Page 38
USB Key (1), Software Updating Menu Main switch Not active Return to SOFTWARE UPDATING MENU INFO: Software installed in Not active oven Ej aktiv INFO: Software accessible Not active via USB key Not active Not active Select Update Only visible if more recent version is available Not active Not active...
Page 39
Not active Not active This function is possible if the controller is updated with software version 1.50 or higher. • Can be downloaded from www.houno.com. 1. Oven must be off. 2. Insert USB key in oven. 3. Turn oven on.
ClimaOptima Calibration Main switch Not active Not active Not active Not active Not active Not active Not active Not active Not active Not active Not active Not active Calibration should be carried out when Step Time Temp. Oven Exhaust CPU board is replaced •...
Door Sensor Calibration Main switch Not active Return to SERVICE MENU Not active Not active Start calibration of door Not active sensor Not active Not active INFO: During the calibra- tion process, the controller finds the set point automa- tically on the basis of the Not active measurements taken with door closed and door open.
Page 42
How to Calibrate Door Sensor Press ”Start Close door calibration” to firmly and start calibration press key process again Press ”OK” to confirm calibration Open door in first step and press key again Note that if the oven is a PassThrough oven, there are two doors to be calibrated. •...
Technical Service Main switch Not active Return to SERVICE MENU Select Test functions Select show oven setup (see pp. 44-50) (see p. 52) Not active Select Edit oven setup (see pp. 53-59) Select Oven number Select New boot logo (see p. 51) (see pp.
Test Functions Main switch Not active Return to TECHNICAL SERVICE Access to Test function, Access to Main alarm oven (see p. 43) (survey of thermo- switches) (see p. 48) Access to Test function, fan Not active (see p. 44) Access to Test function, Not active steam generator (see p.
Page 45
Test Functions, Oven Main switch Not active Return to TEST FUNCTIONS Activate main contactor Activate exhaust motor Activate heat Activate condensation jet Activate cooling fan Not active Activate oven chamber jet Not active Activate interior lighting Not active Heat can only be activated when main contactor and fan motor are on. •...
Page 46
Test FunctionS, Fan Main switch Not active Return to TEST FUNCTIONS Activate low fan speed, Activate low fan speed, motor running left motor running right Activate high fan speed, Activate high fan speed, motor running left motor running right Activate stop Activate main contactor (otherwise motor unable to run)
Page 47
Test Functions, Steam Generator Main switch Confirm level setting Return to TEST FUNCTIONS Activate filling jet Cannot be activated until water level in steam generator is high and main contactor is active. Activate drain pump Not active Not active INFO: Current temperature Not active in steam generator INFO: Water level in steam...
Page 48
Test Functions, CombiWash Main switch Not active Return to TEST FUNCTIONS Activate pump for INFO: Status for water detergent pressure sensor (2 bar pressure sensitive switch) Activate pump for rinse aid Not active Not active Activate solenoid valve for water Not active Not active Not active...
Page 49
Test Functions, Misc. Main switch Not active Return to TEST FUNCTIONS Activate external vent. 1 INFO: Temperature Terminal 4 core temperature probe 1 Not active Activate external vent. 2 Not active Terminal 5 Activate restart lamp INFO: Temperature Core temp. probe 2 Not active Not active INFO: Restart status...
Page 50
Test Functions, Main Alarm Main switch Not active Return to TEST FUNCTIONS Activate main contactor Not active INFO: Shows status of Not active thermo-switch circuit Not active Not active Not active Not active Not active Not active - 50 -...
Oven Number Main switch Press OK to save oven Return to TECHNICAL number, and return to SERVICE TECHNICAL SERVICE Key in 0/A Key in 5/B Key in 1 Key in 6 Key in 2 Key in 7 Key in 8 Key in 3 Key in 9 Key in 4/CE...
Display Oven Set-up Main switch Not active Return to TECHNICAL SERVICE Not active Not active Not active Not active Not active Not active Not active Not active Not active Not active This menu shows the features incorporated in this particular oven. Changes not possible. •...
Oven Set-up 1: Select Generation Main switch Not active Return to TECHNICAL SERVICE Select VC1 for previous Select VC2 for the new generation of Visual generation of Visual Cooking Cooking Not active Not active Not active Not active Not active Not active Not active Not active...
Page 54
Oven Set-up 2: Select Oven Model Main switch Press OK to confirm Return to OVEN SET-UP: SELECT GENERATION Not active Select ”BPE” Not active Select ”CPE” Not active Select ”KPE” Not active Not active Not active Not active We recommend that you write down the settings of DISPLAY OVEN SET-UP before making •...
Page 55
Oven Set-up 3: Select Oven Size Main switch Press OK to confirm Return to OVEN SET-UP: SELECT OVEN MODEL Select oven size 1.06 Select oven size 1.20 Select oven size 1.08 Select oven size 2.10 Select oven size 1.10 Select oven size 2.14 Select oven size 1.12 Not active Select oven size 1.16...
Page 56
Oven Set-up 4 Main switch Press OK Return to OVEN SET-UP: Next menu SELECT OVEN SIZE Not active Is this a PassThrough oven? YES / NO Not active Does oven have a restart button? NONE / DISPLAY / EXTERN / BOTH (PassTrough ovens only) Not active Restart time 1-10 min.
Page 57
Oven Set-up 5 Main switch Press OK Return to OVEN SET-UP Next menu Not active Is oven set-up to be BKI UK* / EUROSP** / CC Menu*** Not active When oven starts, you are logged on as USER / SUPERUSER Not active Is oven to start in recipes? YES / NO...
Page 58
Oven Set-up 6 Main switch Press OK Return to OVEN SET-UP Next menu Not active Does customer want more speeds than high and low? Not active Set hardness of water. 0-8 dH / 8-18 dH / 18→dH Not active Should the level of detergent be monitored? YES / NO Not active...
Page 59
Oven Set-up 7 Main switch Press OK Return to OVEN SET-UP Oven restarts Not active Not active Not active Not active Not active Not active Not active Not active Not active Not active This is the final set-up of the oven. Changes not possible. •...
Logo Main switch Not active Return to SERVICE - ENGINEER Select boot logo if Select boot logo if available, otherwise not available, otherwise not active active Select boot logo if Select boot logo if available, otherwise not available, otherwise not active active Select boot logo if...
Page 61
Logo Main switch Not active Return to TECHNICAL SERVICE Not active Not active Not active Not active Not active Not active Not active Not active Not active Not active Oven restarts automatically after downloading of new logo. • The new boot logo will be active after restart and the logo screen saver appears when •...
Language Update Main switch Select font for the Return to TECHNICAL language in question SERVICE Not active One line up Not active Not active Not active Not active Not active Not active Not active One line down In this menu, you update language files from the USB key. •...
Enter Code Main switch Return to MAIN MENU Confirmation of setting and return to MAIN MENU Press for 0 Press for 5 Press for 1 Press for 6 Press for 2 Press for 7 Press for 3 Press for 8 Press for 4 Press for 9 Codes:...
Error Codes Door open (Close oven door) Error code 2: Generator too hot (Generator thermo-switch has tripped. Reconnect by pressing Error code 3: button under operation panel) Oven too hot (oven thermo-switch has tripped. Reconnect by pressing button under Error code 4: operation panel) Fan too hot (Thermo-switch in motor has tripped.
When the oven was handed over, it was free from any kind of defect. --------------------------------------- -------------------------------------- Signature / date – service engineer Signature / date - customer Send this form by e-mail to kundecenter@houno.com. Or fax it through at +45 87 11 47 10 - 65 -...
Page 66
Access to the oven: All ovens Distance measured in mm Left side minimum 50 mm (2”) Rear side minimum 50 mm (2”) Right side minimum 400 mm (15”) Drain connection: Yes No Heat-resistant drain tube connected. Fall of at least 3º or 5%. CombiPlus fitted with open drain for both ovens.
--------------------------------------- -------------------------------------- Signature / date – Sales person Signature / date - Customer Send this form by e-mail to kundecenter@houno.com Or fax it through at +45 87 11 47 10 - 67 -...
Page 68
Appendix 3 Ovn Set-up (Set-up menu) Nr Parameter Setting Dansk English Deutsch NO, YES Oven light off when door is Sluk ovnlyset ved åben dør (B Ofenlicht aus bei geöffneter Tür. Oven light door open (B oven with lights in ovn med lys i døren).
Page 69
Logging of recipe runs. Loggen von Programläufen. None, Local, Hvilken kilde via web til Select source for SW update Quelle für SW aufdatieren über Update server Houno, opdatering af SW. through web. Web. Laptop PC NO, YES Indstilling for brug til udstillinger...
Need help?
Do you have a question about the CPE 1.10 and is the answer not in the manual?
Questions and answers