Table of Contents
Advertisement
NCL-DSR1 Clear RTC RAM
3 .
3 .
3 . 3 .
C P U f a n p i n s e l e c t i o n ( 3 - p i n F M _ C P U 1 , F M _ C P U 2 )
C P U f a n p i n s e l e c t i o n ( 3 - p i n F M _ C P U 1 , F M _ C P U 2 )
C P U f a n p i n s e l e c t i o n ( 3 - p i n F M _ C P U 1 , F M _ C P U 2 )
3 .
C P U f a n p i n s e l e c t i o n ( 3 - p i n F M _ C P U 1 , F M _ C P U 2 )
C P U f a n p i n s e l e c t i o n ( 3 - p i n F M _ C P U 1 , F M _ C P U 2 )
These jumpers allow you to connect either a 3-pin or a 4-pin CPU fan
cable plug to the CPU fan connectors (CPU_FAN1, CPU_FAN2). Set
these jumpers to pins 1-2 if you are using a 3-pin fan cable plug, or to
pins 2-3 if you are using a 4-pin plug.
NCL-DSR1 FM_CPU setting
4 . 4 .
4 .
4 .
4 .
U S B d e v i c e w a k e - u p ( 3 - p i n U S B P W 1 2 , U S B P W 3 4 )
U S B d e v i c e w a k e - u p ( 3 - p i n U S B P W 1 2 , U S B P W 3 4 )
U S B d e v i c e w a k e - u p ( 3 - p i n U S B P W 1 2 , U S B P W 3 4 )
U S B d e v i c e w a k e - u p ( 3 - p i n U S B P W 1 2 , U S B P W 3 4 )
U S B d e v i c e w a k e - u p ( 3 - p i n U S B P W 1 2 , U S B P W 3 4 )
Set these jumpers to +5V to wake up the computer from S1 sleep
mode (CPU stopped, DRAM refreshed, system running in low power
mode) using the connected USB devices. Set to +5VSB to wake up
from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh,
power supply in reduced power mode).
NCL-DSR1 USB device wake up
A S U S R S 1 6 0 - E 2 / C S 3
A S U S R S 1 6 0 - E 2 / C S 3
A S U S R S 1 6 0 - E 2 / C S 3
A S U S R S 1 6 0 - E 2 / C S 3
A S U S R S 1 6 0 - E 2 / C S 3
CLRTC1
1 2
2 3
Normal
Clear CMOS
(Default)
FM_CPU1
1 2
2 3
DC mode
PWM
(Default)
FM_CPU2
3
2
2
1
DC mode
PWM
(Default)
USBPW12
3
2
2
1
+5V
+5VSB
(Default)
USBPW34
3
2
2
1
+5V
+5VSB
(Default)
4 - 5
4 - 5
4 - 5
4 - 5
4 - 5
Advertisement
Table of Contents
