Download Print this page

Huber CC-E Manual

Immersion circulator

Hide thumbs

Table Of Contents

Table of Contents

Table of Contents
Introduction
Details on the Declaration of Conformity
Safety
Symbols Used for Safety Instructions
Representation of Safety Identifiers
Proper Operation
Reasonably Foreseeable Misuse
Responsible Bodies and Operators - Obligations and Requirements
Obligations of the Responsible Body
Proper Disposal of Resources and Consumables
Requirements for Operators
Obligations of the Operators
General Information
Description of Workstation
Safety Devices to DIN 12876
Further Protective Devices
Power Interruption
Alarm Functions
Warning Messages
Commissioning In-Plant Transport
Lifting and Transporting the Temperature Control Unit
Temperature Control Unit with Lifting Eyes
Temperature Control Unit Without Lifting Eyes
Mounting/Removing Leveling Feet
Positioning the Temperature Control Unit
Temperature Control Unit with Casters
Temperature Control Unit Without Casters
Unpacking
Ambient Conditions
EMC-Specific Notes
Installation Conditions
Recommended Temperature Control and Cooling Water Hoses
Wrench Sizes and Torques
Temperature Control Units with Cooler
Temperature Control Unit with Batch
Operation as Bath Thermostat
Preparations for Operation
Unscrewing/Activating the Leveling Feet (if Any)
Externally Closed and Externally Open Applications
Opening/Closing Valves
Installing Collecting Container
Connecting the Functional Earth
Connecting Externally Closed Application
2.10.1 Connecting an Externally Closed Application
Connecting to the Power Supply
Connection Using Socket with Protective Earth (PE)
2.11.2 Connection Via Hard Wiring
2.11.3 Converting the Power Supply Connection
Function Description
Function Description of the Temperature Control Unit
General Functions
Other Functions
Information on the Thermal Fluids
To be Noted When Planning the Test
Pilot ONE®" Controller
Functional Overview of "Pilot ONE
Clock/Event Function
Rechargeable Accumulator
Programmable Event Function
Event Function "Alarm Clock Event
Event Function "Program Event
Operation Via the Touch Screen
Display Instruments
The Touchscreen [88]
Control Instruments
The Touchbuttons
The Categories
The Sub-Categories
The Dialogs
Function Examples
Display of Software Version
Start & Stop
Copying the Settings to a Data Carrier
Saving to a USB Flash Drive
Loading from a USB Flash Drive
Restore Factory Settings
Restore to Factory Settings Without Overtemperature Protection
Restore to Factory Settings Including Overtemperature Protection
Setup Mode
Turning on the Temperature Control Unit
Turning off the Temperature Control Unit
Setting the Overtemperature Protection
General Information on the Overtemperature Protection
Setting "OT Limit: Heating
Setting "Process Safety
Monitoring Via "Display OT Values
Testing Overtemperature Protection for Functionality
Adjusting the Delta T Limiter
Changing the Delta T Limiter
The Temperature Control Circuit
Select Temperature Control: Internal or Process
Temperature Control to Internal Temperature
Temperature Control to Process Temperature
Delta T Limiter
Monitoring the Pt100 Temperature Sensors
Optimum Control Parameters for Optimum Temperature Control
Sub-Category: "Select Auto/Expert Mode
Sub-Category: "Configuration Auto
Sub-Category: "Find Parameters
Sub-Category: "Control Dynamics
Sub-Category: "Fluid Properties
Sub-Category: "Display Parameters
Sub-Category: "Configuration Manual
Sub-Category: "Change Parameters
Sub-Category: "Display Parameters
Sub-Category: "Control Structure
4.2.10 Sub-Category: "Reset Parameters
4.2.11 Sub-Category: "Display Parameters
4.2.12 Freeze Protection for Temperature Control Unit
4.2.13 Setting the Setpoint Thresholds
4.2.14 Setting the Setpoint
Filling, Venting, Degassing and Draining
Filling, Venting, Degassing and Draining the Bath Thermostat
Filling and Venting the Bath Thermostat and the Externally Closed Application
Degassing of Bath Thermostat
Draining the Bath Thermostat
Normal Operation Automatic Operation
Temperature Control
Starting the Temperature Control Process
Ending the Temperature Control Process
Temperature Control Via a Created Temperature Control Program
Starting the Temperature Control Program
Ending/Cancelling the Temperature Control Program
Interfaces and Software Update
Interfaces at the "Pilot ONE®" Controller
10/100 Mbps Ethernet for RJ45 Network Sockets
USB-2.0 Interface
USB-2.0 Interface, Host
USB-2.0 Interface, Device
Interfaces on the Temperature Control Unit
Interfaces at the Back
Service Interface
Female RS232 Serial
Connection Jack for Pt100 Process Controller Sensor
Firmware Update
Service/Maintenance Messages from the Temperature Control Unit
Electrical Fuse
Replacing the "Pilot ONE
Maintenance
Function Check and Visual Inspection
Replacing Temperature Control or Coolant Hoses
Replacing Temperature Control Hoses
Replacing Coolant Hoses
Thermal Fluid Inspection, Replacement and Circuit Cleaning
Thermal Fluid Inspection
Rinsing the Thermal Fluid Circuit
Cleaning the Surfaces
Plug Contacts
Decontamination/Repairs
Shutting down
Safety Instructions and Basic Principles
Switch-Off
Draining the Temperature Control Unit
Draining the Cooling Water
Draining Process
Deinstalling the Collecting Container
Uninstalling an External Application
Packing
Shipping
Disposal
Contact Data
8.10.1 Telephone Number: Customer Support
8.10.2 Telephone Number: Sales
8.10.3 Email Address: Customer Support
Certificate of Compliance
Annex

Quick Links

1 Table of Contents
2 Introduction
3 Alarm Functions
4 Warning Messages
Download this manual

CC®

Immersion

Circulator

Table of Contents

Need help?

Do you have a question about the CC-E and is the answer not in the manual?

Huber CC-E Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Huber CC-E

Table of Contents