Related Manuals for Creative ZiiSound DSx
Summary of Contents for Creative ZiiSound DSx
- Page 1 Model No./型号: MF8125...
- Page 2 Congratulations on purchasing the ZiiSound DSx Wireless Subwoofer, a perfect complement to the ZiiSound series of wireless speaker systems featuring SLAM (Symmetrically Loaded Acoustic Module) Technology. Experience a whole new definition of freedom in placement for that perfect acoustic projection with our wireless systems.
- Page 3 For detailed product information, instructions or to find out more about our speakers, visit www.creative.com/speakers Safety Instruction Please read the following before using the Creative Products: • Use a mains plug that is appropriate for your country or region. • To be completely disconnected from the power input, the mains plug has to be disconnected /detached from the mains. • Disconnect the mains plug when the device is expected to be unused for several days. Additional guidelines for wireless devices • The short wave radio frequency signals of a wireless device may impair the operation of other electronic and medical devices • Switch off the device where it is prohibited. Do not use the device in medical facilities, aircraft,...
- Page 4 Technical Specifications • Input Rating: 100-240V~ 50/60Hz 300mA • Operating Frequency : 5725 – 5850 MHz • Supported Speaker models : ZiiSound D5x , ZiiSound D3x • Operating Range: Up to 30 meters (Measured in open space. Walls and structures may affect range of device.) • Device Operating Temperature : 0ºC to 50ºC Note: Compliance markings are located at the back of this product. Compatibility Disclaimer • Every electronic device is subjected to radio frequency (RF) interference from external sources. These include the connection between linked ZiiSound D5x, D3x and wireless subwoofer. • Creative will not be liable for any loss of data or leakage resulting from the use of these devices.
- Page 5 Product Overview / Connectivity Diagram ZiiSound DSx LED Status Indicator LED lights up to indicate active wireless link status SLAM Master driver Do not poke objects into these areas SLAM Pressure drivers Do not poke objects into these areas...
- Page 6 LINK Button For various actions to LINK and connect to ZiiSoundD5x or D3x Bass Level Control To Increase or decrease the bass level AC IN Attach supplied AC cord into AC IN, then into mains LED Status Subwoofer Status Standby (Mains Powered ON, not connected to any speaker) LINK discoverable mode Rapid blinking LED LED blinks twice and goes off Restored to Factory default setting LED stays ON Linked to speaker...
- Page 7 To Power ON the ZiiSound DSx Plug in the AC cord into the AC IN and switch on the mains. The ZiiSound DSx is powered ON and in standby mode.
- Page 8 To link up with the ZiiSound D5x or D3x To link to the ZiiSound D5x or D3x master speaker unit, the ZiiSound DSx needs to be in LINK Discoverable mode for the master speaker unit to establish a link to ZiiSound DSx. To activate LINK discoverable mode, follow the instructions below. Link discoverable mode Rapid blinking LED With the Subwoofer mains powered ON, Press and hold the Link button for 4 seconds and release when the LED blinks once. The Subwoofer is now ready to recieve connection from a master speaker unit. Link established with Master Speaker LED lit steady When the Wireless Subwoofer is successfully linked up, the Led Status indicator will be lit steady. Note: At any one time, the ZiiSound DSx can only remember one device in its memory bank.
- Page 9 To de-link the ZiiSound DSx from any master speaker unit To de-link the ZiiSound DSx from any master speaker unit for linking to another master speaker unit, perform the following instructions below. Return to Factory default Two Led Flashes and Led stops blinking With the Subwoofer is powered ON, press and hold the Link button for 10 Seconds until 2 flashes of LED is seen and the LED stops blinking. Subwoofer is cleared of memory and in standby mode. LINK discoverable mode Rapid blinking LED Press and hold the Link button for 4 seconds and release when the LED blinks once. The Sub- woofer is now ready to recieve connection from a master speaker unit.
-
Page 10: Frequently Asked Questions (Faq)
The ZiiSound DSx cannot be Powered ON. What should I do? • Make sure that the power cords are firmly connected to the unit and that the power outlet is turned on. • Press the LINK Button at the rear of the Subwoofer. The LED status indicator should blink. This indicates that the Subwoofer is powered ON and in standby. There’s no wireless link between the ZiiSound DSx and ZiiSound D5x or D3x. What should I do? • Check to see if there is a broken link in the ecosystem. A broken link in the ecosystem will stop the link from functioning until the link is restored. • Perform Steps 3. To link up with the ZiiSound D5x or D3x to put the wireless Subwoofer into LINK Discoverable mode and refer to the ZiiSound D5x or D3x user manual for further linking instructions. Upon successful link, the LED status indicator on the DSx will be lit up... - Page 11 I am having difficulty in linking up the ZiiSound DSx with the ZiiSound D5x or D3x. • Ensure that you have the master speaker defined • Make sure that your Master speaker LINK discoverable mode is enabled • Position them within 1 meter or closer to each other if you experience linking difficulties • Ensure that both, your ZiiSound DSx and your ZiiSound D5x or D3x are not connected to any other devices • Should the problem persist, return the ZiiSound DSx, D5x or D3x to factory default setting by referring to section 5, Reset to factory setting What’s the optimal operating distance between ZiiSound D5x or D3x with the ZiiSound DSx? • The optimal operating distance is within 30 meters. They work best when there are no...
-
Page 12: Regulatory Information
Regulatory Information The following sections contain notices for various countries: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: CAUTION: This product is intended for use with FCC/CE certified computer equipment. Please check the equipment 1. This device may not cause harmful interference, and operating/installation manual and/or with the equipment 2. This device must accept any interference received, manufacturer to verify/confirm if your equipment is including interference that may cause undesired suitable prior to the installation or use of the product. - Page 13 à utiliser l’appareil. interference that may cause undesirable operation. DECLARATION OF CONFORMITY Manufacturer / Importer’s Name : This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: Creative Labs, Inc. 1. This device may not cause harmful interference, and Manufacturer / Importer’s Address : 2. This device must accept any interference 1901 McCarthy Boulevard Milpitas, received, including interference that may cause CA. 95035 United States undesirable operation.
-
Page 14: Notice For Taiwan
Notice for Taiwan Notice for Australia/New Zealand Notice for Singapore Complies with This product complies with the requirements of the ACMA IDA Standards Radiocommunications (Electromagnetic Compatibility) Standard 2008. DB00148... - Page 15 © 2011 Creative Technology Ltd. All rights reserved. Creative, the Creative logo, SLAM™, Zii and ZiiSound are trademarks or registered trademarks of Creative Technology Ltd in the United States and/or other countries. All other trademarks are the property of their respective owners and are hereby recognized as such. All specifications are subject to change without notice.