Related Manuals for MicroPace StimCor
Summarization of Contents
1 INTRODUCTION & ESSENTIAL PRESCRIBING INFORMATION
1.1 Device Description
Details the Micropace Cardiac Stimulator system, its components, and usage.
1.2 Compatible Equipment
Lists compatible equipment for the Micropace Cardiac Stimulator system.
1.3 Important Patient Safety Warnings
Covers general warnings, specific warnings, and RF ablation equipment warnings.
1.4 General Precautions in Handling Stimulator
Provides precautions for installation, transport, storage, and use of the stimulator.
2 DEVICE RATINGS, CLASSIFICATION AND CERTIFICATION
CE Mark Compliance
Details the Micropace Cardiac Stimulator's compliance with EEC directives.
Compliance Testing
Information on bodies that performed compliance testing for the system.
Micropace Cardiac Stimulator classification
Classifications according to TGA, Medical Devices Directives, IEC, and Health Canada.
Micropace Cardiac Stimulator system Power rating
Specifies the power rating for the Micropace Cardiac Stimulator system.
Identification of technical standards
Lists technical standards with which compliance is claimed.
Environmental Conditions
Specifies the operating temperature and humidity range for the device.
3 COPYRIGHT, WARRANTY AND DISCLAIMER NOTICE
Copyright Notice
Details copyright information for Micropace Pty Ltd.
Trademarks
Lists trademarks associated with the Micropace system.
5 EPS320 FAMILY OF CARDIAC STIMULATORS
5.1 Description of Stimulator Family
Describes the EPS320 Cardiac Stimulator as a diagnostic external programmable cardiac stimulator.
6 EPS320B/BT CONFIGURATION
6.1 Description of system
Details the Micropace EPS320B/BT EP Stimulator System as a computerized diagnostic system.
6.2 System Components
Lists the components included in this configuration of the EPS320B/BT system.
7 STIMCORTM CONFIGURATION
7.1 Description of system
Describes the Micropace StimCor™ EP Stimulator System for "Cockpit" laboratories.
7.2 How Supplied
Lists the main components of the StimCor™ system.
7.3 System Components
Illustrates the system components for StimCor™.
7.4 StimCor™ Optional Installation Accessories
States that optional accessories are the same as EPS320B/BT.
8 STIMLABTM CONFIGURATION
8.1 Description of system
Describes the Micropace StimLab™ EP Stimulator System with remote bedside monitor.
8.2 How Supplied
Lists the main components of the StimLab™ system.
8.3 System Components
Illustrates the system components for StimLab™.
8.4 StimLab™ Optional Installation Accessories
Lists optional installation accessories available for the StimLab™ System.
10 USING THE MICROPACE CARDIAC STIMULATORS
10.1 Connecting the Stimulus Connection Box
Instructions for connecting the Stimulus Connection Box (MP3014) to the SGU.
10.2 Switching on the system
Procedure for switching on the computer, LCD screen, and Stimulus Generator Unit.
10.3 Using the computer
Details the front panel of the Bona Light System PC used with the stimulator.
10.4 Setting up the computer
Steps for initial setup and configuration of the computer for the system.
10.5 Indicating location of SGU
Guidance on applying a label to indicate the SGU's location if out of sight.
11 USING THE KEYBOARD AND THE TOUCH DISPLAY
11.1.1 Numeric Keypad
Details the custom Micropace Compact Numeric Keypad Kit and its usage.
11.2.1 Input Device Control
Explains how to use the Input button to select touch screen or keyboard control.
11.2.2 Local/Remote Indicator
Describes the text indicator showing which station has exclusive control.
12 USING THE STIMULATOR SOFTWARE
12.1 Help Function
Explains how to access help for parameters and protocols using the 'H' hotkey.
12.2 Training Videos
Information on accessing training videos from the help menu.
12.3 Help Search
Details how to use the help system's search facility.
12.4 The Main Stimulator Screen
Describes the main screen and focus for adjusting pacing parameters.
12.5 Pacing Parameters
Instructions on setting pacing parameters using hotkeys and +/- keys.
12.6 Basic Pacing
How to toggle pacing on/off using the PACE key or touch button.
12.7 Using the Stimulator Software Protocols
Explains how to use various software protocols like Threshold, Nodal_ERP, etc.
12.8 Pacing Protocols
Details various pre-programmed stimulation protocols available.
12.8.1 Protocol Selection & Renaming
How to select and rename favourite protocols using the Protocol Toolbox.
12.8.2 Pace Protocols
Description of the PACE protocol for fixed interval pacing.
12.8.3 Threshold Protocol
How to use the THRESHOLD protocol to determine pacing current amplitude.
12.8.4 Nodal_ERP Protocol
Details the Nodal_ERP protocol for AV Node refractory measurements.
12.8.5 Multi_Sx Protocol
Describes the Multi_Sx protocol for programmed ventricular stimulation.
12.8.6 Wenckebach Protocol
Explains the Wenckebach protocol with continuous S1 decrement.
12.8.7 RSynced_Sx Protocol
Details the RSynced_Sx protocol for sensed P/QRS complexes.
12.8.8 SNRT* Protocol
Explains the SNRT protocol for elapsed-seconds alarm timer and S1 decrement.
12.8.9 Burst_Pace Protocol
Describes the Burst_Pace protocol for rapid pacing with low S1 values.
12.8.10 AV Atrio-ventricular Delayed Protocol
Details the AV_DELAYED protocol for sequential A-V pacing.
12.8.11 Overdrive Pace and ATP Protocols
Instructions for terminating tachycardia with Overdrive Pace and ATP protocols.
12.8.12 Specialised Protocols
Describes specialised protocols like Bi Ventricular Pacing and Paced S2.
12.9 Software configuration
How to configure program operation and safety limits via the CONFIG menu.
12.10 Sound Configuration
Details how the system outputs sounds to external speakers.
12.11 Safety Features
Procedures for urgent pacing, backup manual pacing, and emergency pace.
12.12 Software Error Messages
Explains runtime timing errors and program warnings on exit.
12.13 Additional Software Messages
Covers advisory messages, text messages, warnings, and error types.
12.13.1 Advisory Messages
Short advisory messages notifying users of abnormal conditions without interruption.
12.13.2 Text Messages
Describes advisory notes, run time warnings, data errors, and file/run time errors.
12.14 Configuring the Program - the CONFIG menu
Details parameters controlling program operation, including safety limits.
13 THE EPS320 STIMULUS GENERATOR UNIT
13.1 EPS320 Stimulus Generator Unit layout
Describes the four sections of the Stimulus Generator Unit's front panel.
Backup Manual Pace Control
How the stimulator switches to Backup Manual Pace mode if computer fails.
Pace Output
Explanation of the Atrium and Ventricle LED indicators for stimulation pulse.
Emergency Fixed Pace Output
Procedure for using the emergency output if the Stimulus Generator Unit fails.
13.2 EPS320 Stimulator Connections
Shows the connectors on the rear panel of the Stimulus Generator Unit.
13.3 Hardware Error Messages on the EPS320 Stimulus Generator Unit
Lists hardware errors appearing on LED displays and their suggested actions.
14 TROUBLESHOOTING
Micropace Stimulator software does not start on turning on the computer.
Troubleshooting steps if the computer does not respond to the keyboard.
Pacing is not capturing and no stimulus artifact is seen.
Steps to diagnose issues with pacing capture and stimulus artifact visibility.
Patient is not capturing but a stimulus artifact is visible.
Troubleshooting steps when a stimulus artifact is visible but no patient capture.
15 MAINTENANCE
15.1 Batteries
Information on internal rechargeable batteries and their replacement.
15.2 Maintenance and Calibration
Details suggested weekly preventative servicing and annual calibration.
15.3 Cleaning Instructions
Guidance on cleaning Stimulator system components safely.
15.4 Serviceable Life and Disposal
Information on the system's expected lifespan and disposal procedures.
Need help?
Do you have a question about the StimCor and is the answer not in the manual?
Questions and answers