Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for HAMAR LASER Dual Scan L-742
Summarization of Contents
Important Notices
Surge Protection Recommendation
Importance of surge protection for laser longevity and warranty.
Laser Warm Up Procedure
Recommended warm-up times for proper calibration and avoiding drift.
L-743 Ultra-Precision Triple Scan Laser
Operating Warning
Crucial warning about operating the laser in an upright position.
Applications Overview
Lists various applications for the L-743 laser system.
Measuring and Aligning Capabilities
Key measurement and alignment capabilities of the L-743.
L-743 Laser Features
Key Features and Specifications
Lists the primary features and specifications of the L-743 laser.
L-733 Precision Triple Scan Laser
Applications
Lists various applications for the L-733 laser system.
Key Features
Lists the primary features and specifications of the L-733 laser.
L-742 Dual Scan Ultra-Precision Roll Alignment Laser
Applications
Lists various applications for the L-742 laser system.
Measuring and Aligning
Key measurement and alignment capabilities of the L-742.
L-732 Dual Scan Precision Roll Alignment Laser
Applications
Lists various applications for the L-732 laser system.
Measuring and Aligning
Key measurement and alignment capabilities of the L-732.
Laser Controls and Differences
Laser Model Differences
Compares accuracy and number of laser planes across models.
Laser Power and Warm-up
Providing Power to the Laser
Details power supply options (battery pack and AC adapter).
Laser Warm Up Procedure
Recommended warm-up times for proper calibration and avoiding drift.
Control Panel Operation
Triple Scan Laser Control Panel
Explains the controls for the L-743 and L-733 lasers.
Dual Scan Laser Control Panels
Explains the controls for the L-742 and L-732 lasers.
Precision Level Vial Calibration
Reading Level Vials
Instructions on how to read the precision level vials.
Calibrating Level Vials
Procedure for calibrating the laser's level vials.
Target Calibration and Setup
Zeroing the Targets
How to reset target readings to zero for accurate measurements.
Calculating Calibration - Roll Axis
Procedure to calculate the calibration for the roll axis level vial.
Level Calibration Calculations
Calculate Set Point - Roll Axis
Formula and example for calculating the roll axis set point.
Setting Level Vials
Setting First Level Vial – Roll Axis
Step-by-step guide to setting the roll axis level vial.
Calculating Calibration - Pitch Axis
Procedure to calculate the calibration for the pitch axis level vial.
Pitch Axis Calibration and Accuracy Check
Setting First Level Vial – Pitch Axis
Step-by-step guide to setting the pitch axis level vial.
Checking Levels for Accuracy
How to verify the accuracy of the level vial settings.
Measurement Overview
General Measurement Principles
Explains how lasers are used for alignment and defining reference points.
Selecting Reference Points
Guidance on choosing appropriate reference points on machines and mills.
Measurement Procedures
Measuring Straightness
Procedure for measuring the straightness of surfaces or axes.
Flatness and Squareness
Measuring Flatness
Procedure for measuring the flatness of surfaces.
Measuring Squareness
Methods for measuring squareness between axes.
Levelness, Parallelism, and Earth Measurements
Measuring Levelness
Procedure for measuring the levelness of surfaces.
Measuring Parallelism
Procedure for measuring parallelism between surfaces.
Level to Earth Measurements
How to perform level to earth measurements using scanning lasers.
Laser Buck-in Procedures
Three Point Buck-In (Flatness)
Procedure for adjusting the laser plane to be parallel to a surface.
Setting Up Equipment for Buck-in
Steps for positioning and securing the laser and target.
Buck-in Execution
Performing Three Point Buck-In
Detailed steps for executing the three point buck-in.
Advanced Buck-in Methods
Three Point Buck-In with Multiple Targets
Procedure using three targets for faster buck-in.
Two Point Buck-In (Straightness)
Procedure for measuring straightness using two points.
Buck-in Method Selection
Normal vs. Remote Buck-In
Guidelines for choosing between normal and remote buck-in methods.
Remote Buck-in Details
Remote Buck-In Procedure
Detailed steps and geometry for the remote buck-in method.
Troubleshooting Guide (Part 1)
Laser and Target Detection Issues
Solutions for when the target LED is not illuminated.
Laser Beam and Turret Problems
Solutions for when the laser beam is not on or turret is not spinning.
Noisy Target Readings
Causes and solutions for noisy target readings on the PDA.
Troubleshooting Guide - Target Readings
Target Reading and LED Issues
Solutions for missing target readings or blinking LEDs.
Troubleshooting Guide - PDA Issues
PDA Errors and Communication Problems
Solutions for PDA errors, crashes, freezing, or no communication.
Equipment Drawings (L-733)
L-733 Precision Geometry Laser Drawings
Detailed diagrams and specifications for the L-733 laser.
Equipment Drawings (L-743)
L-743 Ultra-Precision Geometry Laser Drawings
Detailed diagrams and specifications for the L-743 laser.
Equipment Drawings (L-732)
L-732 Dual Scan Precision Roll Alignment Laser Drawings
Detailed diagrams for the L-732 laser configurations.
Equipment Drawings (L-742)
L-742 Dual Scan Ultra-Precision Roll Alignment Laser Drawings
Detailed diagrams for the L-742 laser configurations.
Calibration Report Interpretation
Target Accuracy Specifications
Explanation of target resolution and accuracy specifications.
Understanding Calibration Graphs
How to interpret the error and measurement data from calibration reports.
Target Optics Care and Cleaning
Required Supplies for Cleaning
Lists necessary supplies for cleaning optical components.
Cleaning Dust and Contamination
Procedures for removing dust and heavy contamination from optics.
Need help?
Do you have a question about the Dual Scan L-742 and is the answer not in the manual?
Questions and answers