Related Manuals for Lyman Victory
Summary of Contents for Lyman Victory
- Page 1 Instruction Guide All-American 8 Turret Press Victory Single Stage Press Ideal C-Frame Press BrassSmith Powder Measure...
- Page 2 All-American 8 Turret Press...
-
Page 3: Table Of Contents
Brass Smith All-American 8 Reloading Press Overview Congratulations on your purchase of the Lyman All- American 8 Reloading Press. Please read over all instructions prior to use. Parts Diagram Body ....7990510 11 Turret Ball Detent Spring . -
Page 4: Body
Unpacking and Assembly 1. Remove press from packaging, ensure all parts are present. • Assembled All- American 8 Press (1) • Handle with knob and jam nut (1) • Primer Catcher (1) • Primer Feed body (1) • 10-32 mounting screws (3) •... -
Page 5: Turret Bolt
NOTE: The priming arm can be used either with the spring assist or without Maintenance and Troubleshooting Your Lyman All-American 8 Press has been designed to give you years of trouble free service, but some preventive maintenance is required. Before using your press, apply a light film of powdered graphite to the bearing surfaces of all moving parts. - Page 6 Victory Single Stage Press...
- Page 7 Brass Smith Victory Reloading Press Overview Congratulations on your purchase of the Lyman Victory Reloading Press. Please read over all instructions prior to use. Parts Diagram Body ....7726200 Shell-Holder Clip .
-
Page 8: Set Screw
Unpacking and Assembly 1. Remove press from packaging, ensure all parts are present. • Assembled Victory Press (1) • Handle with knob and jam nut (1) • Primer Catcher (1) • Primer Feed body (1) • 10-32 mounting screws (3) •... -
Page 9: Primer Catcher
NOTE: The priming arm can be used either with the spring assist or without Maintenance and Troubleshooting Your Lyman Victory Press has been designed to give you years of trouble free service, but some preventive maintenance is required. Before using your press, apply a light film of powdered graphite to the bearing surfaces of all moving parts. - Page 10 Brass Smith Primer Feed Parts Diagram Primer Feed Body ..7726135 11 Mounting Screw ..7726147 Primer Feed Arm..7726139 12 Blast Shield .
- Page 11 Ideal C-Frame Press...
-
Page 12: Toggle
Brass Smith Ideal Reloading Press Overview Congratulations on your purchase of the Lyman Ideal Reloading Press. Please read over all instructions prior to use. Parts Diagram Body ....7726450 Ram Pin. - Page 13 3. Die set up; Follow your die manufactures set up instructions for your particular die or die set. Your Lyman Ideal Reloading Press is now ready for use. Maintenance and Trouble Shooting Before using your press, apply a light film of powdered graphite to the bearing surfaces of all moving parts.
- Page 14 Trouble Shooting Your Lyman Ideal Press has been designed for years of trouble free use. Here are some simple troubleshooting tips. Shell holder loose or falling out. Make sure shell holder clip is installed on ram. Handle loose. Make sure handle is threaded completely into toggle and silver jam nut is tight against toggle.
- Page 15 Brass Smith Powder Measure...
-
Page 16: Set Screw
Brass Smith Powder Measure Overview Lyman’s Brass Smith Powder Measure is unmatched for value, features and performance! Whether dropping charges for small pistol cases or large rifle cases, this measure gives consis- tent and accurate performance. The CNC machined steel metering cylinder features a microm- eter adjustable thimble with reference lines so resetting the measure is easy. - Page 17 Clean the Measure After unpacking the Brass Smith Powder Measure, the entire unit should be thoroughly cleaned to remove any oil or preservatives that cause powder to stick. We recommend the use of alcohol on patches or soft cloths. It is recommended to disassembling the metering cylinder by loosening the brass thumb screw and removing the outer knurled sleeve by unthreading it fully.
- Page 18 Charging the Shell Once your charge weight is set, place a case against the funnel mouth of the drop tube adapter and work the handle of the measure. Note that the charge drops when the handle is in the up position.
- Page 19 Lyman Products will replace any missing hardware free of charge even if you lose it. Lyman Products is so confident you will be happy with your purchase that if for any reason you are not we will take back the product for a full refund within 30 calendar days of your original...
- Page 20 At Lyman, customer satisfaction and quality are our top priorities. If you are experiencing any problem with this product, DO NOT RETURN IT TO YOUR RETAILER. Please, let us help. If the item has a missing part, is damaged, or if you need help with the instructions,...
Need help?
Do you have a question about the Victory and is the answer not in the manual?
Questions and answers