Table of Contents
Advertisement
Traveller, Traveller Lite and Expedition Kit
Operating instructions for electronics
Initial startup (m, °C, 24h)
The functions of the Traveller can be
checked when the battery is inserted:
1. Segment check
2. Beep tone
3. Background
lighting
After this automatic function test, the present
altitude is first displayed briefly after which
the display changes over to the time mode.
The European system of units (height = m,
temperature = °C, time mode = 24h) is stand-
ard.
Initial startup (ft, °F, 12h)
To set the American system of units (height =
ft, temperature = °F, time mode = 12h). Insert
new battery, press the Victorinox emblem
while closing the battery compartment. The
function test then takes place as described
above.
C = continuous pressure
November 5, 2015
Do all segments
light up?
Did you hear a
beep?
Is the light switched
on briefly?
Menu choice
Press the Victorinox emblem briefly to select
the desired menu.
If the button is not pressed for more than 30
min in the "Altimeter", "Alarm" and "Tempera-
ture" menus, the display automatically reverts
to the time mode.
Background lighting
Press the Victorinox emblem for 1.5 seconds
to switch the background lighting on. The
light goes out again 3 seconds after the last
actuation. The background lighting is auto-
matically switched off on changeover to the
setting mode (except in the alarm function).
1/10
Advertisement
Table of Contents
Related Manuals for Victorinox Expedition
Summarization of Contents
Electronics Operating Instructions
Initial Setup Metric Units
Explains the initial function test and default settings in metric units (°C, m, 24h).
Initial Setup Imperial Units
Details the startup sequence for imperial units (°F, ft, 12h), including battery setting.
Menu Navigation Guide
Describes how to select desired menus by pressing the Victorinox emblem.
Background Lighting Control
Explains how to activate and deactivate the device's background lighting feature.
Watch and Time Settings
Setting the Watch Time
Guides on entering time setting mode and adjusting the watch time accurately.
Time Format Configuration
Explains how to switch between 24-hour and 12-hour time formats on the display.
Altimeter Functions and Warnings
Altimeter Setup Procedure
Details the process of setting the altimeter, including weather correction modes.
Altitude Accuracy Factors
Explains how atmospheric pressure affects altitude readings and potential errors.
Altimeter Usage Advisory
Advises against using the altimeter during high-impact sports due to battery life.
Altitude Calculation and Standards
Air Pressure Impact on Altitude
Discusses how weather changes affect altitude readings and the need for readjustment.
Standard Altitude Data
Provides a table of standard temperature and pressure based on altitude for calculations.
Weather Correction Mode Examples
Standard Weather Setting Example
Example demonstrating the 'Stnd' setting based on altitude and temperature difference.
Hot Weather Setting Example
Example illustrating the 'Hot' setting when measured temperature exceeds the standard.
Cold Weather Setting Example
Example showing the 'Cold' setting when measured temperature is below the standard.
Altimeter as Barometer Use
Note on using the altimeter for barometric readings and weather indication.
Barometer Operation
Interpreting Barometer Trends
Explains how to interpret the bar chart for air pressure trends and weather forecasts.
Barometer Display Reset
Describes the procedure for resetting the barometer display to its default state.
Barometer Trend Indicator
Explains the meaning of the arrow indicating air pressure changes and persistence.
Alarm Functionality
Setting the Alarm Time
Guides on how to enter alarm setting mode and set the desired alarm time.
Alarm Activation and Deactivation
Details how to toggle the alarm between ON and OFF states and stop an active alarm.
Alarm Acknowledgement
Explains how to stop an active alarm and switch it off by briefly pressing the emblem.
Countdown Timer Operations
Setting the Countdown Duration
Instructions for setting the countdown timer duration using the emblem.
Managing Countdown Timer
Covers switching off, restarting, and resetting the countdown timer.
Timer (Stopwatch) Functions
Starting and Stopping the Timer
Details on how to start, stop, and resume the walking/travel timer function.
Resetting the Timer
Explains the procedure to reset the timer to zero (0) after use.
Unit Settings and Battery Management
Configuring Unit Preferences
Describes changing temperature and altitude units (Celsius/Fahrenheit, m/ft).
Battery Status Indicators
Explains battery status indicators like 'LoPo' (low power) and 'noLi' (no light).
Battery Replacement Guide
Provides instructions on how to change batteries for the electronic system and LED module.
Need help?
Do you have a question about the Expedition and is the answer not in the manual?
Questions and answers