Related Manuals for LOFTNESS 71
Summarization of Contents
Warranty Policy
Warranty Requirements
Details the necessary steps for submitting a warranty claim.
Limitations of Warranty
Outlines conditions and parts not covered by the warranty policy.
Exclusions of Warranty
Specifies items and situations explicitly excluded from warranty coverage.
Introduction
Owner Information
Provides essential details for operating and maintaining the machine.
Serial Number Location
Identifies the location of the serial number tag and stamping on the machine.
Manual Storage
Advises on proper storage of the owner's manual and documentation.
Battle Ax Features
Lists the key features and design aspects of the Battle Ax skid loader.
Safety Instructions
Safety First
Explains safety alert symbols and hazard warning word conventions.
Owner's Responsibility
Details the operator's mandatory responsibilities for safe operation.
Mandatory Shut-Down Procedure
Step-by-step instructions for safely shutting down the machine.
Safety Rules
General safety guidelines and precautions for operating the machine.
Hydraulic Safety
Specific safety precautions related to the hydraulic system.
Battle Ax Skid Loader Identification
Illustrates and labels the main components of the skid loader.
Safety Decal Locations
Details the placement and meaning of various safety decals on the machine.
Set-up Instructions
Pusher Bar Assembly
Step-by-step guide for assembling the pusher bar attachment.
Installing the Battle Ax to the Loader
Instructions for securely mounting the Battle Ax to the skid loader.
Checking Rotor Rotation
Procedure to verify the correct direction of the rotor's rotation.
Checking Rotor Speed
How to measure and verify the rotor's operating speed.
Skid Adjustment
Instructions for adjusting the height of the skid shoes.
Cutter Bar Adjustment
Guide for adjusting the position of the cutter bar relative to the rotor.
Operating Instructions
Getting Started
Initial advice and preparation for operating the machine.
Operation
General instructions and safety precautions during machine operation.
Log Moving
Procedure for moving logs and brush using the pusher bars.
Hydraulic Hose Storage
Instructions for properly storing hydraulic hoses when the machine is not in use.
Maintenance
General Maintenance
Overview of routine inspection, lubrication, and repair tasks.
Maintenance Schedule
A table outlining service points and required maintenance intervals.
Lubrication
Guidance on lubricating various machine components.
Grease Point Location
Identifies the specific locations for greasing the machine.
Overhung Load Adapter
Instructions for servicing the overhung load adapter.
Removing Belt Cover
Steps for removing the drive belt cover.
Removing Motor Cover
Steps for removing the motor cover.
Belt Adjustment
Procedure for adjusting the drive belt tension.
Tooth Removal and Installation
Instructions on how to remove and install the cutting teeth.
Tooth Sharpening (Quadco)
Detailed instructions for sharpening Quadco cutting teeth.
Storage
Procedures for storing the machine at the end of the season.
Motor & Sheave Selection Chart
Chart to help select appropriate motors and sheaves based on GPM.
Troubleshooting
Common problems, their causes, and solutions for the machine.
Parts Identification
Battle Ax Body Assembly
Diagram and parts list for the main body of the Battle Ax.
Belt and Sheaves (Parker Motor)
Parts list for belt and sheave assemblies for Parker motors.
Belt and Sheaves (Muncie Motor)
Parts list for belt and sheave assemblies for Muncie motors.
Motor Shield with Gauge (N45262)
Diagram and parts for the motor shield and gauge assembly.
Hydraulics, Parker Motor with Brake
Diagram and parts list for hydraulic components with a Parker motor and brake.
Hydraulics, Parker Motor No Brake
Diagram and parts list for hydraulic components with a Parker motor without a brake.
Valve, Open Loop CW (N21669)
Diagram and parts list for the open loop control valve.
Hydraulics, Muncie Motor
Diagram and parts list for hydraulic components with a Muncie motor.
Hydraulic Motor, 62.9cc (N34676)
Diagram and parts for the 62.9cc hydraulic motor.
Overhung Load Adapter (N16416)
Diagram and parts for the N16416 overhung load adapter.
Valve, Cross Port Relief (N34677)
Diagram and parts for the cross port relief valve.
Manifold, Relief 5000 PSI, Check (200655)
Diagram and parts for the relief manifold.
Hydraulic Motor, Variable 80cc to 110cc (N38488)
Diagram and parts for the variable hydraulic motor.
Overhung Load Adapter (N51193)
Diagram and parts for the N51193 overhung load adapter.
Rotor (with Double Carbide Teeth) 61" (203047), 71" (203050)
Diagram and parts for rotors with double carbide teeth.
Rotor (with Quadco Planer Teeth) 61" (N49368), 71" (N49371)
Diagram and parts for rotors with Quadco planer teeth.
Rotor (with Quadco Planer Hard Surface Teeth) 61" (203177), 71" (203179)
Diagram and parts for rotors with Quadco planer hard surface teeth.
Rear Cutter Bar 61" (N20281), 71" (N21908)
Diagram and parts for the rear cutter bar.
Manual Holder
Diagram and parts for the manual holder.
Machine Decals and Signs
Displays various safety and identification decals for the machine.
Appendix
Specifications
Lists the technical specifications for the Battle Ax skid loader.
Dimensions
Provides detailed measurements and dimensions of the machine.
Torque Specifications
Lists torque values for various hardware sizes and grades.
Need help?
Do you have a question about the 71 and is the answer not in the manual?
Questions and answers