Related Manuals for HARVEY Hydroclave MC10
Summarization of Contents
Introduction
Operation Overview
Overview of the sterilizer's operational principles.
Drying Cycle
Explains the automatic drying phase at the end of the sterilization cycle.
Operator Maintenance Overview
Importance of establishing and following the maintenance schedule.
Safety Information
Alert Signals and Symbols
Explains warning, caution, and note symbols for safety and equipment care.
Declaration of Conformity
Statement of compliance with relevant EMC and Safety standards.
Equipment Symbol Descriptions
Explains various symbols used on the sterilizer for identification and warnings.
General Description
Intended Use and General Usage
Describes the intended applications and general guidelines for product usage.
Operating Features Overview
Lists key features like preset cycles, automatic drying, and printer capabilities.
Control Panel Functionality
Details the components, indicators, and buttons of the sterilizer's control panel.
Sterilizer Accessories
Illustrates and lists standard and optional accessories for the sterilizer.
Printer and Non-Recirculating Accessory
Describes the optional printer and the non-recirculating water accessory.
Sterilization Monitoring Program Recommendations
Recommendations for monitoring sterilization effectiveness using indicators.
Operation
Basic Operation Steps
Provides a step-by-step guide for operating the sterilizer.
Patient Safety Zone Warning
Warning about operating the sterilizer within a specific distance of patient treatment points.
Power On and Initial Setup
Instructions for powering on the sterilizer and control panel.
Filling the Reservoir
Procedure for filling the water reservoir with the correct type of water.
Non-Recirculating System Operation Guide
Guides for filling the cooling tank and emptying the collection bottle.
Overflow Tube Installation and Load Chart
Instructions for installing the overflow tube and guidelines for loading items.
Item Preparation and Loading Procedures
Steps for cleaning items and properly loading them into the chamber.
Locking Door and Selecting Cycle
How to close the door and choose the correct sterilization cycle.
Starting Cycle and Understanding Drying Phase
Procedures for initiating the cycle and understanding the drying phase.
Open Door Drying Procedure
Detailed steps for performing open door drying for improved results.
Removing the Sterilized Load Safely
Instructions and safety precautions for removing items after sterilization.
Additional Information
Cycle Management and Power Issues
Procedures for cancelling cycles, emergency power off, and handling power failures.
Diagnostic Messages
Lists error messages and recommended actions for troubleshooting.
Troubleshooting Common Operational Problems
Addresses issues like wet loads and inadequate drying time.
Printer Operations
Printer Installation and Functionality
Instructions for installing the MC8 printer and operating the printer.
Paper Roll and Ribbon Replacement
Guides for replacing the paper roll and ribbon in the printer.
MC10 Printer Removal Procedure
Instructions for removing the printer from the MC10 model's recess.
Operator Maintenance
Daily and Weekly Cleaning Tasks
Procedures for daily door gasket cleaning and weekly chamber/tray cleaning.
Reservoir and Exterior Cleaning Procedures
Steps for cleaning the water reservoir and the sterilizer's exterior surfaces.
Reservoir Filter Cleaning Guide
Instructions for removing and cleaning the reservoir filter screen.
Chamber Filter Screen Cleaning
Procedure to clean the filter screen located in the water fill port.
Periodic Maintenance Tasks (When Required)
Covers emptying collection bottle, cleaning printer recess, and replacing door gasket.
Pressure Relief Valve Check Procedure
How to test the proper operation of the pressure relief valve.
Cooling Tank Maintenance Schedule
Procedure for draining and rinsing the non-recirculating water cooling tank.
Recommended Spare Parts
Essential Spare Parts List
Lists key spare parts recommended for prompt replacement when needed.
Installation
Cabinet Setup and Electrical Connection
Guidelines for leveling the cabinet, ensuring clearance, and making electrical connections.
Non-Recirculating Accessory Installation
Step-by-step instructions for installing the optional non-recirculating water accessory.
Setting the Clock and Calendar
Detailed steps for setting the internal clock and calendar display.
Activating Non-Recirculating Feature
Procedure to activate the non-recirculating feature after installation.
Configuring Sterilizer Settings
Steps to configure language, units, and clock format via the control panel.
Changing Recirculation Mode
Instructions on how to switch between recirculating and non-recirculating modes.
Technical Data
Device Specifications and Ratings
Lists detailed technical specifications, dimensions, weights, and electrical ratings.
Appendix
Voltage Conversion Procedures
Instructions for performing voltage conversion on dual voltage models.
115 VAC to 230 VAC Conversion
Detailed steps for converting the sterilizer from 115V to 230V operation.
230 VAC to 115 VAC Conversion
Detailed steps for converting the sterilizer from 230V to 115V operation.
Two Year Limited Warranty
Warranty Terms and Conditions
Details the warranty period, coverage, exclusions, and repair procedures.
Need help?
Do you have a question about the Hydroclave MC10 and is the answer not in the manual?
Questions and answers