Brinsea Ova-Easy 380 User Instructions
  1. Manuals
  2. Brands
  3. Brinsea Manuals
  4. Water Pump
  5. Ova-Easy 380
  6. User instructions

Brinsea Ova-Easy 380 User Instructions

Advance humidity pump
Hide thumbs

Advertisement

Table of Contents

Advance Humidity Pump
Ova-Easy 190 / 380 / 580 Advance
Ova-Easy Advance Hatcher
TLC-40 / TLC-50 Advance
Vetario S40M / S50M / T40M / T50M
Contents
Section Subject
1
2
3
4
5
6
7
8
9
10
11
12
EX Upgrade Kit for:
User Instructions
1
AD25 GB Issue 04
Page
2
3
3
5
6
7
8
8
9
9
10
10

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Ova-Easy 380 and is the answer not in the manual?

Questions and answers

Related Manuals for Brinsea Ova-Easy 380

Summarization of Contents

Introduction to Advance Humidity Pump
Unpacking the Advance Humidity Pump Kit
Check Kit Contents and Condition
Verify all parts are present and undamaged after unpacking.
Pump Capstan Mounting Note
Note that the pump capstan is deliberately mounted at an angle.
Product Registration and Guarantee
Register your product online for a free 2-year guarantee.
Join Brinsea Email Group
Register for the Brinsea Email Group for news and offers.
Evaporation Block Installation for Ova-Easy
Positioning the Pump Module
Place the pump module on the incubator top or nearby flat surface (within 0.5m).
Connect Signal Lead
Plug the signal lead connector into the Ova-Easy Advance control socket.
Prepare and Insert Water Tube
Cut and insert the silicone tube, fitting a rigid pipe, through the guide to the evaporation block.
Position Water Tray
Slide the water tray into the incubator, ensuring the tube lies without kinks.
Evaporation Block Installation for TLC Brooder/Vetario
Position Pump and Connect Signal Lead
Place pump module near unit, plug signal lead into control socket.
Prepare and Insert Water Tube
Cut silicone tube and insert rigid pipe into evaporation block mesh.
Fit Evaporation Block and Water Pan
Place block in water pan, then lift pan into slots on heater enclosure.
Pump Installation for All Models
Peristaltic Pump Tube Replacement
Replace thick silicone tube on pump rotor every 3 months for optimal performance.
Connect Inlet and Outlet Tubing
Fit thin and thick tubes to pump nipples, routing them to the water tank and unit.
Operating the Advance Humidity Pump
Filling Water Tank and Unit Setup
Fill tank correctly, do not immerse pump, set unit vents to mid position.
Setting Humidity Level
Navigate menu using +/- buttons to set desired RH%, then save setting.
Pump Operation and Humidity Control
Pump operates when humidity is below set level; it won't run if temperature is too low.
Humidity Fluctuation and Limitations
Humidity may fluctuate +/- 1-2%; the system only increases humidity, not reduces it.
Guidelines for Egg Incubation Humidity Levels
Recommended Humidity Ranges
Specific RH ranges for poultry, waterfowl during incubation and hatching.
Monitoring Humidity via Egg Weight Loss
Use egg weight loss (13-16%) to determine and adjust humidity levels for species.
Guidelines for Brooder/Intensive Care Humidity
Optimal Humidity for Brooding and Care
Maintain 45-55% RH for brooding chicks; avoid high levels to prevent condensation.
Routine Maintenance Procedures
Changing the Peristaltic Pump Tube
Replace pump tube every 3 months to ensure proper water flow and prevent flattening.
Changing the Evaporation Block
Change block regularly for good evaporating efficiency and to prevent bacterial contamination.
Servicing Requirements
No lubrication or further servicing is required beyond the instructions provided.
Troubleshooting Humidity Control Issues
Humidity Not Low Enough
Increase fresh air ventilation; ambient air moisture can limit low humidity.
Humidity Not High Enough
Restrict fresh air; check tubing for kinks or flattening, replace pump tube if needed.
Servicing and Calibration Details
Initial Failure Checks
Check signal cable connection and ensure unit temperature is above low alarm point.
Pump Operation Conditions
Pump runs when asterisk shown next to RH%; operates when measured humidity is below set level.
Pump Motor Replacement
Pump motor is easily replaced using basic tools; instructions are supplied with replacement.
Sensor Calibration
Sensor calibrated at manufacture; user recalibration not recommended; refer to unit instructions.
Spare Parts Availability
Spare evaporation blocks and silicone tube available from Brinsea Products Ltd.
Product Specifications

Table of Contents