Advertisement
Quick Links
Advertisement
Related Manuals for Ingersoll 4118
Summarization of Contents
Safety Information
Warning Before Starting Engine
Crucial pre-operation safety instructions for starting the engine.
Safety Alert Symbol and Notations
Notations Explained
Defines NOTE, IMPORTANT, CAUTION, WARNING, and DANGER symbols used in the manual.
Safety Messages
ANSI Safety Guidelines
Lists critical safety rules provided by the American National Standards Institute (ANSI).
Attachment Manual References
Advises referring to specific operator manuals for attachments.
Hillside (Slope) Operation
General Slope Operation Warnings
Warns about improper operation on slopes and advises following specific instructions.
Learning Safe Operation Practices
Emphasizes learning controls, tractor limits, and terrain knowledge for safe operation.
Hillside (Slope) Operation Guidance
Terrain Knowledge and Obstacle Avoidance
Advises inspecting terrain for obstacles and understanding conditions for safe operation.
Adapting to Changing Operating Conditions
Explains how attachments and weight affect tractor characteristics and operating conditions.
Introduction
Manual Purpose and Usage
Explains the importance of the manual for maintaining the tractor in top operating condition.
Notices and Regulations
Covers spark arrester requirements and Canadian radio interference regulations.
Product Identification
Tractor and Engine Identification Numbers
Details the P.I.N. and serial numbers needed for parts and information.
Operating Controls and Instruments
Indicator Lights and Lever Functions
Explains battery light, PTO light, neutral light, and hydraulic lift lever.
Operating Instructions
Throttle, Choke, and PTO Control
Describes using the throttle, choke, and engaging/disengaging the hydraulic PTO.
Range Selector Operation
Details how to select between low and high ranges for operation.
Operating Controls and Functions
Parking Brake, Steering, and Brake Pedal
Explains parking brake, steering wheel operation, and brake pedal function.
Travel Control, Ignition, Lights, Hourmeter
Covers travel control, ignition key, headlights, and hourmeter usage.
Prestarting Precautions
General Pre-Operation Checks
Lists essential checks before starting the engine, including controls and environment.
Fuel Handling and Safety
Provides critical safety guidelines for handling gasoline to prevent fire hazards.
Starting Procedures
Control Position and Warm-up
Details control positions and engine warm-up procedures, especially for hydraulics.
Engine Starting Sequence
Step-by-step instructions for starting the tractor engine using the ignition key.
Stopping Procedure
Tractor Stopping Sequence
Outlines the sequence for safely stopping the tractor and engine.
Post-Stop Safety Precautions
Emphasizes setting parking brake, removing key, and disengaging power before dismounting.
Operating Procedure
Gear Range Selection and Load Handling
Explains LOW/HIGH ranges and cautions for pulling loads and using equipment.
Tractor Operating Procedures
Forward, Reverse, and Hillside Travel
Details forward/reverse travel, including critical instructions for hillside operation.
Preventive Maintenance
Maintenance Importance and Attachment Notes
Stresses maintenance importance and provides notes on operating attachments like tillers.
Maintenance Chart
Scheduled Maintenance Intervals
Outlines required maintenance procedures and their frequencies based on hours of use.
Chassis Lubrication
Greasing Front Axle and Spindles
Details how to grease front wheel spindles, bearings, and axle pivot pins.
Brake Linkage Oiling Procedure
Explains applying oil to brake linkage pivot points every 50 hours or yearly.
Hydraulic System Maintenance
Hydraulic Oil and Filter Change
Step-by-step guide for draining, changing, and refilling hydraulic oil and filter.
Hydraulic Oil Cooler Care
Advises keeping the hydraulic oil cooler clean for proper function.
Wheel Alignment and Transaxle
Toe-In Adjustment Procedure
Describes how to measure and adjust toe-in for front tires.
Transaxle Oil Service
Details checking and changing the transaxle oil based on hours of use.
Brake Adjustment
Brake Adjustment Procedure
Step-by-step guide to adjust the tractor's brakes for proper stopping.
Seat Maintenance and Adjustment
Seat Cleaning, Care, and Safety Switch
Provides instructions for seat care, adjustment, and the function of the safety switch.
Fuel Filter Replacement
Fuel Filter Replacement Steps
Step-by-step guide for replacing the fuel filter, including safety precautions.
Storage Battery Maintenance
Battery Safety, Water, and Removal
Covers battery dangers, adding water, and safe removal/installation procedures.
Electrical System Maintenance
Battery Terminals and Jump Starting
Instructions for cleaning terminals and the procedure for jump-starting.
Fuse Replacement
Explains how to replace the 30-amp fuse protecting the electrical circuits.
Headlight Bulb Replacement
Headlight Bulb Replacement Steps
Step-by-step instructions for replacing a headlight bulb.
Wiring Diagram
Component and Wire Color Identification
Lists and identifies electrical components and wire colors in the diagram.
Specifications
Engine, Electrical, and Hydraulic Specs
Lists key technical specifications for the engine, electrical system, and hydraulics.
Transaxle, Speed, and Tire Specifications
Details specifications for the transaxle, travel speed ranges, and tires.
Overall Measurements and Capacities
Tractor Dimensions and Weights
Provides overall length, wheelbase, height, weight, and other key measurements.
Fluid Capacities
Lists the required capacities for hydraulic, engine crankcase, and fuel tank.
Manual Ordering Procedure
Manual Availability and Ordering
Lists available manuals and provides instructions for ordering them.
Need help?
Do you have a question about the 4118 and is the answer not in the manual?
Questions and answers