Lexicon 300 V3.0 - QUICK REFERENCE GUIDE REV 1 Quick Reference Manual

MIDI
48 kHz
44.1 kHz
32 kHz
LEVEL
300
DIGITAL EFFECTS SYSTEM
V3.0 Setups
The 300 is organized into Setups and Effects. Setups are
collections of many decisions, including DSP routing (single or
split), Input levels, Source, Balances, LFO Rate and Shape,
and one (or two) Effects. These decisions are grouped to-
gether, named, and stored so they can be called up with a
single user action.

Single Setups

Single Setups unify both
Machine A and Machine B
into a single DSP engine.
Setup Selection
Press SETUP SELECT,
then use the Soft knob to
select a Setup Preset.
When you have found a Pre-
set you want to load, press
ENTER.

Editing an Effect

Press EFFECT EDIT
Press the buttons above or
below a parameter label to
select it.
Storing your changes
Once you have made changes to an Effect, remember that
you must not only store those changes in Effect Edit mode,
but also must store the Setup in which the Effect is loaded.
Note: If the 300 Copy Tools function is set to DISABLE, no STORE
functions can be performed.This function is enabled in CNTRL mode.
(Selection of CNTRL does not interrupt audio operation of the 300.)
The 300 V3.0 factory default state is: Analog In; 48kHz sampling rate.
All Single Setup Presets are
factory loaded with an Effect
of the same name. (The Ef-
fect number may not be the
same.)
An asterisk (*) in a Preset
name indicates that one or
more parameters
patched to the Soft knob.
Press PAGE UP to display
any Soft knob patches
made to Setup Effect para-
meters; press VALUE
show the parameter values.
Turn the Soft knob to in-
.
crease or decrease the pa-
rameter value.
300 V 3.0 Quick Reference Guide
PAGE
UP
PAGE
DOWN
—
To simplify the choice
among the many possible
effect and system routings,
the 300 is shipped with 100
Setup Presets.
Analog
L
Analog
Level
R
L
Digital
Level
R
Digital
Single Setup Presets
P101 Large Hall
P102 Medium Hall
P103 Small Hall
are P104 *Church
P105 *Rooms
P106 RehursalRoom
P107 *Chamber
P108 LiveDrumRoom
P109 *Studio A
P110 *Studio B
P111 *Brick Wall
P112 *Deep End
to
P113 Oil Tanker
P114 *Synth Hall
P115 Dance Hall
P116 *Ambience
P117 In A Room
Press PAGE DOWN
additional parameter pages;
press EFFECT EDIT
turn to the main edit screen.
From Effect Edit mode,
press STORE . Turn the
Soft knob to find an avail-
able register, then press
STORE again.
SETUP CONTROL
7 8 9
SELECT
MACH SETUP
4 5 6
EDIT
STORE EFFECT
1 2 3
EDIT
ENTER VALUE MOD
0
EDIT
The Setup Presets are or-
ganized as follows:
101-150 = Single Setups
201-225 = Dual Mono Setups
301-325 = Cascade Setups
Dry
Analog
Effect
Balance
Edit A
Dry
Digital
Balance
P135 Phase Invert
P118 Stairwell
P136 2 Frame Dly
P119 *Hangar
P137 3 Frame Dly
P120 MarbleFoyer
P138 4 Frame Dly
P121 EarlyReflect
P139 MS Decode
P122 Lecture Hall
P140 *MultiEchoes
P123 *CarInterior
P141 LFO Panner
P124 Score Stage
P142 Telephone
P125 Gate It!!
P143 *Stereo Shift
P126 *Rich Plate
P144 Octave Down
P127 Glossy Plate
P145 Vox Chorus
P128 Warm Plate
P146 Pole Flange
P129 Perc Plate
P147 Bulkie Roll
P130 Contem-Plate
P148 Heavy Roll
P131 *EKO Plate
P149 *Going, Going
P132 Bright Plate
P150 Zorch!
P133 *Round Plate
P134 StereoAdjust
to view
Press VALUE
between a display of pa-
to re-
rameter names and a dis-
play of their values.
From Setup Edit mode,
press STORE
Soft knob to find an avail-
able register, then press
STORE again.
BYPASS
A
BYPASS
B
POWER
Overall
Mix
Analog and
Digital Out
to alternate
. Turn the