Page 1
SUPER AUDIO CD PLAYER DCD-2000AE OPERATING INSTRUCTIONS BEDIENUNGSANLEITUNG MODE D’EMPLOI ISTRUZIONI PER L’USO INSTRUCCIONES DE OPERACION GEBRUIKSAANWIJZING BRUKSANVISNING...
Page 2
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. THE SUPER AUDIO CD PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL. • DECLARATION OF CONFORMITY...
Page 3
SVENSKA NOTE ON USE / HINWEISE ZUM GEBRAUCH / OBSERVATIONS RELATIVES A L’UTILISATION / NOTE SULL’USO NOTAS SOBRE EL USO / ALVORENS TE GEBRUIKEN / OBSERVERA • Avoid high temperatures. Allow for sufficient heat dispersion when installed in a rack. •...
Page 4
SVENSKA NEDERLANDS A NOTE ABOUT RECYCLING: This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with the local recycling regulations. When discarding the unit, comply with local rules or regulations. Batteries should never be thrown away or incinerated but disposed of in accordance with the local regulations concerning chemical waste.
Page 5
FRONT PANEL / FRONTPLATTE / PANNEAU AVANT PANNELLO FRONTALE / PANEL FRONTAL / VOORPANEEL / FRONTPANELEN !3 !2 DCD-2000AE SUPER AUDIO CD PLAYER REAR PANEL / RÜCKWAND / PANNEAU ARRIERE IL PANNELLO POSTERIORE / PANEL TRASERO / ACHTERPANEEL / BAKSIDAN...
ENGLISH Getting Started Thank you for purchasing this DENON Super Audio CD Player. Please read the operation instructions thoroughly in order to acquaint yourself with the Super Audio CD player and achieve maximum satisfaction from it. Be sure to keep these instructions for future reference, should any questions or problems arise.
Caution on handling Discs 2 Super Audio CD Only Super Audio CD discs containing one of the logos shown at the right can be played on this set. There are three types of Super Audio CDs. q Single layer disc Single layer Super Audio CD with only an HD layer.
ENGLISH Getting Started Inserting the batteries • The DCD-2000AE can be controlled from a distance using the included remote control unit (RC-997). Remove the remote control unit’s rear cover. Place 2 R03/AAA batteries in the battery compartment in the direction indicated by the marks.
Part names and functions Front panel POWER switch • Press once to turn the power on. • If a disc is loaded when the power is turned on, playback starts automatically. • Press again to set to the “OFF” position and turn the power off.
ENGLISH Getting Started Display This lights when a CD is loaded or the Super Audio CD’s CD layer mode is set. This lights when the track number is displayed. This lights to indicate the time display mode. There light to indicate the currently playing audio. L : Left channel R : Right channel This lights in the random play mode.
Connections to the analog output terminal • Use the included RCA pin-plug cord to connect the left (L) and right (R) output terminal (ANALOG OUT) of the DCD-2000AE to the CD, AUX or TAPE PLAY left (L) and right (R) input terminal of the amplifier.
ENGLISH Operation Normal playback • The layer for top priority playback after the disc is loaded can be set. • The layer set for top priority playback upon shipment from the factory (default setting) is the Super Audio CD (stereo) layer. SUPER AUDIO CD SET UP POWER...
Starting playback POWER Press the switch to turn on the power. Press the button. • The disc holder opens. Load the disc you want to play. For instructions on loading discs, refer to “OPENING AND CLOSING THE DISC HOLDER AND LOADING DISCS”...
ENGLISH Operation Finding the desired spot while listening to the sound (Remote control unit only) [Manual search] • Use this function to skip forward or backward while listening to the sound. This function comes in handy for finding the desired spot in the middle of long tracks. 2 Searching forward During playback, press and hold in the button.
REPEAT Turn on the power of all system components. Set the input selector on the amplifier to correspond to the inputs the CD player is connected to. Make sure a disc has been loaded in the disc holder. Check the time on the timer and then set the desired turn-on time.
3. Are the amplifier and speakers operating properly? If the DCD-2000AE does not seem to be functioning properly, check the table below. If this does not solve the problem, the DCD- 2000AE may be defective. Turn off the power, unplug the power cord from the power outlet, and contact your store of purchase or nearest Denon sales office.
Main Specifications 2 Audio • Analog output Number of channels: Frequency response: Frequency response range: Signal-to-noise ratio: Dynamic range: Harmonic distortion: Wow and flutter: Output voltage: Signal system: Sampling frequency: Discs: • Digital output Coaxial: Optical: Light emission wavelength: 2 General characteristics Power supply: Power consumption: Maximum external dimensions:...
DEUTSCH Erste Schritte Vielen Dank, daß sich für diesen DENON Super-Audio-CD-Spieler entschieden haben. Lesen Sie sich die folgende Bedienungsanleitung bitte vollständig durch, so daß Sie sich mit den verschiedenen Funktionen des Gerätes vertraut machen und diese optimal ausnutzen können. Bewahren Sie diese Anleitung zum späteren Nachschlagen unbedingt auf, falls sich Fragen oder Probleme ergeben sollten.
Vorsichtsmassnahmen zur Handhabung Discs 2 Super-Audio-CD Auf diesem Gerät können nur Super-Audio-CD-Discs abgespielt werden, die eines der rechts gezeigten Logos enthalten. Es gibt drei verschiedene Typen von Super-Audio-CDs. q Einschicht-Disc Einschicht-Super-Audio-CD bestehen aus nur einer einzigen HD-Schicht. w Doppelschicht-Disc Super-Audio-CD mit einer doppelten HD-Schicht liefern eine längere Wiedergabezeit und erstklassige Tonqualität.
DEUTSCH Erste Schritte Einlegen der Batterien • Der DCD-2000AE kann mit Hilfe des mitgelieferten Fernbedienunges (RC-997) bequem aus dem Sessel bedient werden. Entfernen sich Fernbedienunges befindliche Abdeckung. Legen Sie die 2 R03/AAA-Batterien entsprechend der Markierungen in das Batteriefach ein. Setzen Sie die Abdeckung wieder auf.
Bezeichnung der teile und deren funktionen Frontplatte POWER-Schalter • Drücken Sie diese Taste einmal, um das Gerät einzuschalten. • Wenn eine Disc bei Einschalten des Gerätes eingelegt ist, startet die Wiedergabe automatisch. • Drücken Sie die Taste noch einmal auf die “OFF”- Position, um das Gerät auszuschalten.
DEUTSCH Erste Schritte Anzeige Leuchtet, wenn eine CD eingelegt oder der CD-Schicht- Modus der Super-Audio-CD eingestellt ist. Leuchtet, wenn die Titelnummer angezeigt wird. Leuchtet im Zeitanzeige-Modus. Leuchtet, um den gegenwärtigen Audiokanal anzuzeigen. L : Linker Kanal R : Rechter Kanal Leuchtet im Zufallswiedergabe-Modus.
Anschlüsse Anschlüsse an die Analog-Ausgangsbuchsen • Verwenden Sie das mitgelieferte RCA-Steckerkabel, um die linke (L) und rechte (R) Ausgangsbuchse (ANALOG OUT) des DCD- 2000AE an die linke (L) und rechte (R) CD-, AUX- oder TAPE PLAY-Eingangsbuchse des Verstärkers anzuschließen. Anschlüsse an die Digital-Ausgangsbuchse (COAXIAL/OPTICAL) HINWEIS: •...
DEUTSCH Betrieb Normale wiedergabe • Die Schicht-Wiedergabepriorität kann nach Einlegen der Disc eingestellt werden. • Die für die Wiedergabepriorität eingestellte Schicht ist ab Werk (Grundeinstellung) auf Super-Audio-CD (Stereo)-Schicht eingestellt. SUPER AUDIO CD SET UP POWER Öffnen und schliessen der plattenlade und einlegen einer CD POWER Drücken Sie den...
Wiedergabe starten POWER Drücken Sie den -Schalter, um das Gerät einzu-schalten. Drücken Sie die -Taste. • Die Plattenlade wird geöffnet. Legen Sie die CD ein, die Sie abspielen möchten. Beziehen Sie sich für Anleitungen zum Einlegen von Discs auf “ÖFFNEN UND SCHLIESSEN DER PLATTENLADE UND EINLEGEN EINER CD”...
DEUTSCH Betrieb Auffinden eines Titels während des schnellen Suchlaufs (Nur Fernbedienung) [Manueller Suchlauf] • Diese Funktion verwenden, Tonwiedergabe schnell durch die Disc zu springen. Diese Funktion ist nützlich, wenn Sie einen bestimmten Abschnitt in einem langen Titel finden wollen. 2 Manueller Suchlauf vorwärts Drücken und halten Sie während der Wiedergabe -Taste.
Abspielen von Titeln in zufällige Reihenfolge (Nur Fernbedienung) [Zufallswiedergabe] • Sämtliche sich auf der Disc befindliche Titel können auch in zufälliger Reihen-folge abgespielt werden. Drücken Sie im Stoppmodus die Taste. • Die “RANDOM”-Anzeige leuchtet. Wenn die Taste während der Wiedergabe gedrückt wird, startet die Zufallswiedergabe ab diesem Titel.
3. Funktionieren der Verstärker und die Lautsprecher einwandfrei? Wenn Sie den Eindruck haben, daß der DCD-2000AE nicht ordnungsgemäß funktioniert, überprüfen Sie bitte die in nachfolgender Tabelle aufgeführten Punkte. Sollte sich die Störung nicht beheben lassen, ist der DCD-2000AE möglicherweise defekt. Schalten Sie das Gerät aus, trennen Sie das Netzkabel vom Netz ab und kontaktieren Sie Ihren Fachhändler oder einen sich in Ihrer Nähe...
Page 30
FRANCAIS Introduction Merci d’avoir acheté ce lecteur de Super Audio CD DENON. Veuillez lire ce mode d’emploi de façon à bien connaître le lecteur de Super Audio CD et d’en profiter au maximum. Conservez ce mode d’emploi pour vous y référer ultérieurement en cas de question ou de problème.
Precautions de manipulation Disques 2 Super Audio CD Seuls les disques Super Audio CD contenant l’un des logos figurant à droite peuvent être lus sur cet appareil. Il existe trois types de Super Audio CD. q Disque simple couche Super Audio CD avec une seule couche HD. w Disque double couche Super Audio CD avec une double couche HD, disposant d’une durée de lecture plus longue et d’une qualité...
FRANCAIS Introduction Insertion des piles • Le DCD-2000AE peut être commandé à distance à l’aide de la télécommande fournie avec l’appareil (RC-997). Enlever la trappe à l’arrière de la télécommande. Placer 2 piles R03/AAA dans le compartiment dans le sens indiqué...
Nomenclature et fonctions Panneau avant Commutateur POWER • Appuyer une fois sur ce touche pour mettre l’appareil en marche. • Si un disque se trouve dans le lecteur lorsque l’appareil est mis en marche, la lecture démarre automatiquement. • Appuyer une nouvelle fois sur ce touche pour le mettre en position Arrêt “OFF”...
FRANCAIS Introduction Affichage S’allume lorsqu’un CD est chargé ou que le mode de couche CD du Super Audio CD est activé. S’allume lorsque le numéro de la plage est affiché. S’allument pour indiquer le mode d’affichage du temps. S’allume pour indiquer le canal audio en cours de lecture. L : Canal gauche R : Canal droit S’allume en mode de lecture aléatoire.
Connexions Connexions à la prises de sortie analogique • Utilisez le câble à broche RCA fourni pour connecter les prises de sortie (ANALOG OUT) gauche (L) et droite (R) du DCD- 2000AE aux prises d’entrée gauche (L) et droite (R) CD, AUX ou TAPE de l’amplificateur. Connexions à...
FRANCAIS Fonctionnement Lecture normale • Il est possible de régler la couche à lire en priorité après le chargement du disque. • La couche à lire en priorité réglée par défaut à l’assemblage de l’appareil est la couche Super Audio CD (stéréo). SUPER AUDIO CD SET UP POWER...
Démarrage de la reproduction Appuyez sur la commutateur mettre l’appareil sous tension. Appuyer sur la touche • Le réceptacle de disque s’ouvre. Chargez le disque que vous voulez reproduire. Pour plus d’informations sur le chargement des disques, voir “OUVERTURE ET FERMETURE DU RECEPTACLE DISQUE CHARGEMENT D’UN DISQUE”...
FRANCAIS Fonctionnement Rechercher une plage en écoutant à grande vitesse (Télécommande uniquement) [Recherche Manuelle] • Utiliser cette fonction pour sauter rapidement à travers le disque pendant l’écoute du son. Cette fonction est pratique lorsqu’on veut repérer une certaine section dans une plage longue.
Lecture de plages en ordre aléatoire (Télécommande uniquement) [Lecture Aléatoire] • Toutes les plages enregistrés sur le disque peuvent être lues une fois en ordre aléatoire. En mode d’arrêt, appuyer sur la touche RANDOM • Le témoin “RANDOM” s’allume. Si enfoncée pendant la lecture, la lecture aléatoire commence à...
3. L’amplificateur et les haut-parleurs fonctionnent-ils correctement? Si le DCD-2000AE semble ne pas fonctionner correctement, vérifier le tableau ci-dessous. Si le problème n’est pas résolu, le DCD- 2000AE peut être endommagé. Eteindre l’appareil, débrancher le câble d’alimentation et contacter le revendeur ou le point de vente DENON le plus proche.
Caracteristiques principales 2 Audio • Sortie analogique Nombre de canaux: Réponse en fréquence: Etendue de la réponse en fréquence: Rapport signal-bruit: Gamme dynamique: Distorsion harmonique: Pleurage et scintillement: Tension de sortie: Système de signaux: Fréquence d’échantillonnage: Disques: • Sortie numérique Coaxial: Optical: Longueur d’onde de l’émission lumineuse:...
ITALIANO Guida introduttiva Grazie per avere acquistato il lettore di Super Audio CD di DENON. Leggere attentamente le istruzioni per familiarizzare con il lettore di Super Audio CD e ottenere così risultati ottimali. Conservare queste istruzioni per riferimento futuro, nel caso in cui dovessero verificarsi problemi.
Precauzioni sul maneggio Dischi 2 Super Audio CD Sull’unità possono essere riprodotti solo i dischi Super Audio CD che contengono uno dei loghi mostrati a destra. Sono disponibili tre tipi di Super Audio CD. q Disco a layer singolo Il Super Audio CD a layer singolo è costituito da un solo layer w Disco a layer doppio Super Audio CD con un doppio layer HD, che offre tempo di riproduzione esteso e un’elevata qualità...
ITALIANO Guida introduttiva Inserimento delle batterie • Il DCD-2000AE può essere controllato a distanza utilizzando il telecomando (RC-997). Togliete il coperchio sul retro del telecomando. Inserite 2 batterie R03/AAA nel vano batterie rispettando le polarità. Chiudete il coperchio. Portata operativa del telecomando 30°...
Nomenclatura e funzionamento delle parti Pannello anteriore Interruttore POWER • Premete questo tasto una volta per accendere la corrente. • Se un disco viene caricato quando l’unità è accesa, la riproduzione viene avviata automaticamente. • Premete lo stesso tasto nuovamente nella posizione “OFF”...
ITALIANO Guida introduttiva Display Si illumina quando viene caricato un CD oppure viene impostata la modalità layer CD del Super Audio CD. Si illumina quando viene visualizzato il numero della traccia. Si illuminano per indicare la modalità di visualizzazione del tempo.
• Utilizzare il cavo della presa pin RCA in dotazione per collegare i jack di uscita (ANALOG OUT) sinistro (L) e destro (R) dell’unità DCD-2000AE ai jack di ingresso CD, AUX o TAPE PLAY sinistro (L) e destro (R) dell’amplificatore.
ITALIANO Operazione Riproduzione normale • È possibile impostare il layer per la riproduzione con priorità alta dopo che il disco è stato caricato. • Il layer impostato con priorità di riproduzione alta alla consegna (impostazione predefinita) è il layer del Super Audio CD (stereo). SUPER AUDIO CD SET UP POWER...
Inizio della riproduzione POWER Premete l’interruttore l’unità. Premete il tasto • Il piatto portadisco si apre. Caricare il disco nel piatto portadisco. Per informazioni sul caricamento dei dischi, fare riferimento alla sezione “APERTURA E CHIUSURA DEL PIATTO PORTADISCO E CARICAMENTO DEI DISCHI”...
ITALIANO Operazione Localizzazione di un brano quando ascoltate ad alta velocità (Solo telecomando) [Ricerca manuale] • Potete saltare sul disco mentre ascoltate i contenuti ad alta velocità. Questa funzione è molto utile per la localizzazione di una certa parte nel mezzo di un brano lungo, da cui far iniziare la riproduzione.
Riproduzione ripetuta (Solo telecomando) 2 Riproduzione ripetuta di tutti i brani [Ripetizione di tutti i brani] Premete il tasto REPEAT una volta nel modo di arresto. • Si illumina l’indicatore “REPEAT ALL”. Premete il tasto Potete anche impostare il modo di riproduzione ripetuta di tutti i brani premendo il tasto durante la riproduzione.
3. L’amplificatore e gli altoparlanti funzionano correttamente? Se il DCD-2000AE sembra funzionare in modo anomalo, controllate la seguente tabella. Se non si riesce a risolvere il problema, forse il DCD-2000AE è guasto. Spegnete la corrente, scollegate il cavo di alimentazione dalla presa murale e rivolgetevi al luogo di acquisto o al più...
Specifiche principali 2 Audio • Uscita analogica No. di canali: Risposta in frequenza: Intervallo della risposta di frequenza: Rapporto segnale/rumore: Gamma dinamica: Distorsione armonica: Wow & Flutter: Voltaggio di uscita: Sistema di segnali: Frequenza di campionamento: Discs: • Uscita digitale Coaxial: Optical: Lunghezza d’onda dell’emissione di luce:...
Primeros pasos Gracias por adquirir este reproductor de Super Audio CD de DENON. Por favor, lea por completo las instrucciones de uso para familiarizarse con el reproductor de Super Audio CD y obtener máxima satisfacción de su uso. Asegúrese de guardar estas instrucciones para consultarlas más adelantes si surge alguna pregunta o problema.
Precaucion en el manejo Discos 2 Super Audio CD En esta unidad sólo se pueden reproducir los discos de Super Audio CD que contengan alguno de los logotipos que aparecen a la derecha. Hay tres tipos de Super Audio CD. q Disco de una capa Super Audio CD de una sola capa que consiste en una única capa HD.
Primeros pasos Introducción de las pilas • El DCD-2000AE puede ser controlado a distancia por medio de la unidad de mando a distancia incluido (RC-997). Quite la tapa posterior de la unidad de mando a distancia. Coloque 2 pilas “AAA” (R03) ben el compartimiento de pilas, en la dirección indicadas por las marcas.
Nombre y función de las partes Panel frontal Interruptor POWER • Pulse una vez para activar la alimentación. • Si se carga un disco cuando la alimentación está activada, se reproduce automáticamente. • Pulse otra vez para ajustar a la posición “OFF” y así desactivar la alimentación.
Primeros pasos Visualización Se ilumina cuando se carga un CD o cuando está activo el modo de capa CD de Super Audio CD. Se ilumina cuando aparece el número de pista. Se iluminan para indicar el modo de mostrar hora. Se ilumina para indicar el actual de audio en reproducción.
• Utilice el cable con clavija RCA que viene con la unidad para conectar las clavijas de salida izquierda (L) y derecha (R) (ANALOG OUT) del DCD-2000AE a las clavijas de entrada izquierda (L) y derecha (R) de CD, AUX o TAPE PLAY del amplificador.
Operacion Reproducción normal • Se puede fijar la capa de reproducción de mayor de prioridad después de cargar el disco. • La capa que viene predeterminada de fábrica con prioridad de reproducción es la capa Super Audio CD (estéreo). SUPER AUDIO CD SET UP POWER Apertura y cierre del portadisco y carga de...
Para iniciar la reproducción POWER Pulse el interruptor unidad. Pulse el botón • La portadisco se abre. Cargue disco compacto reproducir. Para informarse sobre cómo cargar discos, consulte “APERTURA Y CIERRE DEL PORTADISCO Y CARGA DE UN DISCO” ( página 7). Para los Super Audio CD, utilice el botón SUPER AUDIO CD SETUP para fijar la capa...
Page 62
Operacion Para localizar una pista escuchando su sonido a alta velocidad (Unidad de mando a distancia sólo) [Búsqueda manual] • Utilice esta función para saltar rápidamente por el disco mientras escucha la música. Esta función es muy útil cuando se desea encontrar una sección determinada dentro de una pista larga.
Repetición de la Reproducción (Unidad de mando a distancia sólo) 2 Repetición de la reproducción de todas las pistas [Repetición de todas las pistas] Estando en el modo de parada, pulse el botón REPEAT una vez. • Se iluminará el indicador “REPEAT ALL”. Pulse el botón El modo de repetición de todas las pistas puede REPEAT...
DCD-2000AE tuviera alguna avería. Desactive la alimentación, desenchufe el cable de alimentación de la toma de red general, y póngase en contacto con la tienda de compra o con la oficina de ventas DENON más próxima.
Especificaciones principales 2 Audio • Salida de análoga Número de canales: Respuesta de frecuencia: Margen de respuesta de frecuencia: Relación señala a ruido: Intervalo dinámico: Distorsión armónnica: Lloro y tremolación: Voltaje de salida: Sistema de señal: Frecuencia del muestreo: Discs: •...
Aan de slag Hartelijk dank voor de aankoop van deze DENON Super Audio CD-speler. Lees de gebruiksaanwijzing aandachtig door om uzelf vertrouwd te maken met de Super Audio CD-speler en optimaal van dit toestel te genieten. Bewaar deze gebruiksaanwijzing om hem ook in de toekomst, wanneer u vragen of problemen heeft, te kunnen raadplegen.
Informatie over het hanteren van discs Discs 2 Super Audio CD Op dit toestel kunnen uitsluitend Super Audio CD’s met één van de rechts getoonde logo’s worden afgespeeld. Er zijn drie soorten Super Audio CD’s. q Disc met enkele laag Super Audio CD met enkele laag die alleen een HD-laag heeft.
Aan de slag Het inleggen van de batterijen • De DCD-2000AE kan op afstand worden bediend met behulp van de bijgeleverde afstandsbediening (RC-997). Open het deksel van het batterijencompartiment aan de achterkant van de afstandsbediening. Leg 2 R03/AAA batterijen in het batterijencompartiment en let hierbij op de polariteit zoals die door de merktekens wordt aangegeven.
Benaming en funkties van onderdelen Voorpaneel POWER-schakelaar • Eenmaal indrukken om de spanning in te schakelen. • Als de spanning is ingeschakeld en een disc wordt geplaatst, start de weergave automatisch. • Nogmaals indrukken om de “OFF”-stand in te stellen en de spanning uit te schakelen.
Aan de slag Display Licht op wanneer een CD wordt geplaatst of de weergave van de CD-laag van de Super Audio CD is ingesteld. Licht op wanneer het tracknummer wordt weergegeven Lichten op om de tijdweergavestand aan te duiden. Licht op om het momenteel weergegeven audiokanaal aan te duiden.
• Gebruik de bijgeleverde RCA-penstekkerkabel om de linkse (L) en rechtse (R) uitgangsaansluitingen (ANALOG OUT) van de DCD-2000AE op de linkse (L) en rechtse (R) CD-, AUX- of TAPE PLAY-ingangsaansluitingen van de versterker aan te sluiten. Aansluitingen op de digitale uitgangsaansluiting (COAXIAL/OPTICAL) OPMERKING: •...
Bediening Normale weergave • Het is mogelijk in te stellen welke laag de hoogste prioriteit heeft en wordt weergegeven nadat een disc wordt geplaatst. • Bij verzending vanuit de fabriek is de Super Audio CD-laag (stereo) ingesteld als laag met de hoogste weergaveprioriteit (standaardinstelling).
Beginnen met afspelen POWER Druk op de -schakelaar om de CD- speler aan te zetten. Druk op de -toets. • De dischouder wordt geopend. Leg de CD die u wilt afspelen in de lade. Zie “HET OPENEN EN SLUITEN VAN DE DISKHOUDER EN HET INLEGGEN VAN EEN CD”...
Bediening Opsporen van een passage in hoge snelheid onder het luisteren (Enkel afstandsbediening) [Handopsporing] • U kunt de disk in hoge snelheid doorlopen onder het luisteren. Deze funktie is handig voor het opzoeken van een bepaald gedeelte in het midden van een lange passage om vandaar de weergave te starten. 2 Voorwaarts zoeken Druk tijdens de weergave op de houdt deze ingedrukt.
Herhalingsweergave (Enkel afstandsbediening) 2 Alle stukken herhaaldelijk weergeven [Alle stukken herhalen] Druk in de stopstand eenmaal op de REPEAT-toets. • De “REPEAT ALL”-indicator licht op. Druk op de -toets. U kunt de herhaalde weergave van alle tracks ook instellen door tijdens de weergave op de te drukken.
Overloop de onderstaande tabel indien de DCD-2000AE niet naar behoren lijkt te werken. Indien u het probleem niet kunt oplossen aan de hand van de tabel, is de DCD-2000AE mogelijk beschadigd. Schakel de spanning uit, haal het netsnoer uit het stopcontact en neem contact op met uw verkooppunt of het dichtstbijzijnde DENON-verkoopkantoor.
Komma igång Tack för att du köpt denna Super Audio CD-spelare från DENON. Läs bruksanvisningen noggrant för att bekanta dig med spelaren och få ut så mycket som möjligt av den. Behåll bruksanvisningen för framtida referens för att kunna få svar på frågor och lösa ev. problem.
SVENSKA Viktigt vid användningen Skivor 2 Super Audio CD Endast Super Audio CD som är märkta med en av de logotyper som visas till höger kan spelas på denna apparat. Det finns tre typer av Super Audio CD. q Enkelskiktsskiva Super Audio CD som endast består av ett HD-skikt.
Komma igång Isättning av batterier • DCD-2000AE kan fjärrstyras på bekvämt avstånd med hjälp av fjärrkontrollen (RC-997). Öppna batterifackets lock på fjärrkontrollen. Sätt i 2 R03/AAA-batterier i batterifacket i den riktning som indikeringarna visar. Sätt på locket. Fjärrkontrollens arbetsområde 30°...
SVENSKA De olika delarnas namn och funktioner Frontpanelen POWER-knapp • Tryck en gång för att slå på strömmen. • Om en skiva ligger i apparaten när strömmen slås på startar avspelningen automatiskt. • Tryck en gång till till läge “OFF” för att stänga av strömmen.
Komma igång Display Denna lyser när en CD laddas eller när Super Audio CD:ns CD-skikt är inställt. Denna lyser när spårnumret visas. Lyser för att ange tidvisningsläge. Lyser för att ange den audiokanal som används för tillfället. L : Vänster effektkanal R : Höger effektkanal Lyser under slumpmässig avspelning.
• Använd den medföljande RCA-kabeln med stiftkontakter för att ansluta vänster (L) och höger (R) utgångarna (ANALOG OUT) på DCD-2000AE till vänster (L) och höger (R) ingångarna för CD, AUX eller TAPE PLAY på förstärkaren. Anslutning av den koaxiala digitalutgången (COAXIAL/OPTICAL) OBSERVERA : •...
Gör så här Avspelning • Det prioriterade skiktet för avspelning när skivan laddas kan ställas in. • Prioriterat skikt för avspelning vid leveransen från fabriken (grundinställning) är Super Audio CD-skiktet (stereo). SUPER AUDIO CD SET UP POWER Hur man öppnar och stänger skivsläden och lägger i en skiva POWER Tryck på...
SVENSKA Starta avspelning POWER Tryck på -knappen för att slå på strömmen. Tryck på -tangenten. • Skivsläden öppnas. Lägg den skiva du vill spela på skivsläden. För instruktioner om hur du laddar skivor, se “HUR MAN ÖPPNAR OCH STÄNGER SKIVSLÄDEN OCH LÄGGER I EN SKIVA”...
Gör så här Lokalisering av en melodi med hjälp av snabblyssning (Endast fjärrkontrollen) [Snabbspelning] • Du kan snabbt gå genom skivans melodier med hjälp av snabblyssningsfunktionen. Funktionen är praktisk för att snabbt hitta en punkt mitt i en melodi och starta avspelningen därifrån.
SVENSKA Repetitionsavspelning (Endast fjärrkontrollen) 2 Spela alla spår upprepade gånger [Repetering av alla spår] Tryck på REPEAT-tangenten en gång från stoppläget. • Indikatorn “REPEAT ALL” tänds. Tryck på eller -tangenten. Du kan även ställa in läget för repeterad avspelning av REPEAT alla spår genom att trycka på...
3. Fungerar förstärkaren och högtalarna normalt? Om du misstänker att DCD-2000AE inte fungerar normalt, skall du kontrollera felet enligt felsökningsschemat nedan. Om schemat inte kan lösa problemet, kan DCD-2000AE ha skadats. Stäng av strömmen, dra ur anslutningskabeln från strömuttaget och kontakta din affär där du köpte enheten eller närmaste DENON-säljkontor.
Need help?
Do you have a question about the DCD-2000AE and is the answer not in the manual?
Questions and answers