Related Manuals for Rockford Fosgate punch 250.2 power
Summarization of Contents
Introduction to 50 Series
Punch Amplifier Accessory Pack
Lists included components for amplifier installation and setup.
Technical Design Features
trans•nova Technology
Patented circuit for superior sound quality, efficiency, and reliability.
DIAMOND Circuitry
Reduces high frequency distortion for lower distortion and stability.
TOPAZ Noise Isolation
Solves ground loop noise issues for improved noise rejection.
DSM Manufacturing Process
Improves reliability, signal-to-noise ratio, and sonic performance.
XCard Internal Crossover
Provides flexible, precise electronic crossover for system design.
Stereo Pass-Thru Feature
Allows convenient daisy-chaining of additional amplifiers.
Balanced Line Inputs (50.2)
Offers superior noise rejection for signal integrity.
NOMAD Advanced Protection
Ensures fast protection without degrading sound quality.
MOSFET Devices
Offers advantages over bi-polar design for speed and linearity.
ITS Thermal Stability
Maximizes power supply efficiency by reducing heat generation.
50.2 Design Features
Heatsink and End Caps
Describes the cooling system and aesthetic design elements.
Terminals and Jacks
Details speaker, power, REM, and RCA connections.
Input and Switching Controls
Covers signal input selection and gain adjustments.
50.1 Design Features
Heatsink and End Caps
Describes the cooling system and aesthetic design elements.
Terminals and Jacks
Details speaker, power, REM, and RCA connections.
Summed Stereo/Mono Switch
Selects signal input usage for driving the amplifier.
Installation Considerations
Installation Safety and Planning
Provides rules for safe installation and wire routing.
Mounting Locations
Trunk Mounting Recommendations
Guidance on optimal vertical mounting for cooling.
Passenger Compartment Mounting
Requirements for adequate airflow and air gap.
Engine Compartment Mounting Warning
Prohibits installation in engine bay due to warranty voiding.
Wiring the System
Wire Routing and Preparation
Guidelines for signal and power wire placement and stripping.
Connecting Power and Ground
Steps for connecting B+, REM, and ground terminals.
Speaker Connection
Instructions for connecting speakers and maintaining polarity.
Using the XCard
XCard Crossover Configuration
Details setting XCards for HP, LP, or Full Range operation.
Customizing the XCard
Explains how to alter crossover points by changing resistor values.
50.2 Installation
50.2 Power Connections
Illustrates two options for connecting power and remote turn-on leads.
Stereo Operation Setup
Describes connections and switch settings for stereo mode.
Bridged Operation Setup
Details settings for bridged stereo and EZ-bridged configurations.
Using the 50.2 Signal Switching Network
Audiophile Bypass Configuration
Explains bypassing crossover circuitry for better sound.
12dB Octave Filter Setup
Guides on configuring 12dB filters for amplifier and Pass-Thru.
24dB Octave Filter Setup
Guides on configuring 24dB filters and bandpass for amplifier and Pass-Thru.
Using the 50.2 Balanced Line Inputs
Connecting the Balanced Line Transmitter
Explains using BLT for improved signal integrity.
Setting Input Levels with BLT
Details process for adjusting gain and voltage levels.
50.1 Installation
50.1 Power Connections
Illustrates two options for connecting power and remote turn-on leads.
Mono Operation Setup
Describes connections and switch settings for mono mode.
Stereo Operation Setup (Two 50.1)
Details wiring two 50.1 amps for stereo output.
Stereo/Mono Operation Setup
Describes settings for stereo/mono configuration.
Bridged Mono Operation Setup
Details wiring for bridged mono configuration.
Using the 50.1 Signal Switching Network
"Audiophile Bypass" the 50.1
Explains bypassing crossover circuitry for better sound.
Configure 12dB Octave Filter
Guides on configuring a 12dB low-pass filter.
Configure 24dB Octave Filter
Guides on configuring a 24dB low-pass filter.
System Diagrams
100 Watt System Diagram
Illustrates a 100W system configuration.
150 Watt System Diagram
Illustrates a 150W system configuration.
300 Watt System Diagram
Illustrates a 300W system configuration.
500 Watt System Diagram
Illustrates a 500W system configuration.
Rockford Fosgate Accessories
Balanced Line Transmitter (FG-BLT)
Details the accessory for converting signals and reducing noise.
Troubleshooting
Amplifier Power Issues
Diagnoses and remedies when the power LED is off.
No Sound Issues
Diagnoses and remedies when the power LED is on but no sound.
Speaker Output Problems
Addresses low output, distortion, and noise.
Pass-Thru Output Problems
Troubleshoots issues with the Pass-Thru output.
Autosound 2000's Quick Check
Noise Troubleshooting Method
Outlines a systematic approach to identifying noise sources.
Dynamic Power Measurements
Understanding PowerCube Measurements
Explains IHF-202 standards and speaker impedance.
Limited Warranty Information
Warranty Coverage and Exclusions
Details what is covered, not covered, and limitations.
Obtaining Service and Contact Info
Provides instructions and addresses for warranty service.
Need help?
Do you have a question about the punch 250.2 power and is the answer not in the manual?
Questions and answers