LITHIUM LED SPOTLIGHT
INSTRUCTION MANUAL
3
2
1
4
5
7
6
8
10
SAVE THIS INSTRUCTION MANUAL FOR FUTURE
REFERENCE.
BC
Copyright © 2024
Baccus Global LLC, Boca Raton, FL 33432
1-877-571-2391
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not approved by the party responsible for compliance could void
user's authority to operate the equipment.
SAFETY GUIDELINES /
DEFINITIONS
DANGER:
Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING:
Indicates a potentially hazardous situation which, if not avoided, may result
in death or serious injury.
CAUTION:
Indicates a potentially hazardous situation which, if not avoided, may result in
minor or moderate injury.
Used without the word, indicates a safety related message.
NOTICE:
Indicates a practice not related to personal injury which, if not avoided, may result
in property damage.
RISK OF UNSAFE OPERATION.
When using tools or equipment, basic safety precautions
should always be followed to reduce the risk of personal injury. Improper operation,
maintenance or modification of tools or equipment could result in serious injury and
property damage. There are certain applications for which tools and equipment are designed.
Manufacturer strongly recommends that this product NOT be modified and/or used for any
application other than for which it was designed. Read and understand all warnings and
operating instructions before using any tool or equipment.
READ ALL INSTRUCTIONS
WARNING:
READ ALL INSTRUCTIONS BEFORE OPERATING THIS SPOTLIGHT.
Failure to follow all instructions listed below may result in electric shock, fire and/or serious
injury.
IMPORTANT SAFETY
INSTRUCTIONS
GENERAL SAFETY WARNINGS AND INSTRUCTIONS
WARNING –
RISK OF FIRE, ELECTRIC SHOCK, BURST HAZARD, OR INJURY TO PERSONS
– when using electrical appliances, basic precautions should always be followed, including
the following:
• LED gets HOT quickly!
• Do not touch the LED at any time when operating.
• Only contact trigger when turning on.
• Do not touch hot lens or enclosure.
• Do not remain in light if skin feels warm.
• Do not operate the spotlight with a missing or damaged lens or enclosure.
WARNING –
WHEN USING ELECTRICAL APPLIANCES, basic precautions should always be
followed, including the following:
• The spotlight and the supplied USB charging cable are not toys and cannot be played with
as toys. To reduce the risk of injury, close supervision is necessary when these units are used
near children.
• Use only attachments recommended or sold by the manufacturer.
WARNING –
TO REDUCE THE RISK OF ELECTRIC SHOCK:
• Do not put the spotlight in water or other liquid. Do not place or store this light where it can
fall or be pulled into water or become wet.
• Charge indoors only. Do not expose charging cable to water or any other liquid.
• Do not clean this appliance with a water spray or the like.
• Use only the charging cable supplied by the manufacturer to charge and recharge.
WARNING –
FIRE HAZARD: Never contact combustible material to the lens or heat sink.
CAUTION –
TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• All lights give off heat:
– Do not touch lens while operating.
– Keep combustibles away from spotlight lens. Extreme heat can cause fires.
– Never place the light face down on any surface when lit, charging or not in use. Never
store the light face down on any surface.
• Never look directly into the light or shine the light into another person's eyes. Serious eye
injury could occur.
• Keep sharp objects away from lens — it is glass and can break.
• Do not immerse spotlight in water.
• Do not expose this unit to extremely high temperatures.
• Do not drop or throw spotlight. It contains glass and a lithium battery.
• Use only with the USB charging cable that is provided with unit. Plug in the charging cable at
the light first, then plug into the charging source.
• After charging/recharging, disconnect the USB charging cable and wait 5 minutes before use.
• Do not crush, cut, pull or expose charging cable to extreme heat.
• Position charging cable so it does not become entangled or become a safety hazard. Keep
charging cable away from sharp edges.
• Use in a dry location only.
• There are no user-serviceable parts inside. Do not attempt to disassemble any other parts of
the unit.
• To reduce risk of damage to electric plug and cord, pull by plug rather than cord when
disconnecting.
• Do not attempt to charge the unit if the charging cable is damaged.
SL10LEDS
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM
BATTERIES
WARNING –
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, BURST HAZARD, OR INJURY
TO PERSONS OR PROPERTY:
Lithium batteries are small, compact and ideal for providing long-lasting power to this unit.
However, they must be used and charged properly. Improper use can result in serious injury,
fire, or death.
• Lithium batteries can explode in the presence of a source of ignition. Do not use the product
in the presence of an open flame.
• Do not place this lithium battery powered unit in fire or apply heat to it.
• Do not subject this lithium battery powered unit to strong impacts or shocks. The battery in
this unit contains safety and protection devices which, if damaged, may cause the battery to
generate heat, rupture or ignite.
• Do not expose this lithium battery powered unit to water or salt water, or allow the battery
to get wet.
• Avoid storing this lithium battery powered unit in the basement, bathroom or other areas of
the house that are or may become wet or humid or where moisture may concentrate.
• Do not leave this lithium battery powered unit in direct sunlight, or use or store the unit inside
cars in hot weather. Doing so may cause the battery to generate heat, rupture, or ignite.
Using the battery in this manner may also result in a loss of performance and a shortened
life expectancy.
• Never charge this unit near heat or flammable objects.
NEVER THROW WATER ON A BURNING LITHIUM BATTERY!
•
does catch on fire, it will burn even more violently if it comes in contact with water or even
moisture in the air. A fire extinguisher must be used.
Battery Charging and Capacity
This unit is delivered in a partially charged state – you must fully charge it before using it for
the first time.
When stored at room temperature with a full charge, lithium batteries will begin to discharge
from the time they are manufactured, even when unused. Deep discharges also decrease their
capacity. Battery life can be extended by the following:
• Charge battery to full capacity before storage.
• Optimal storage temperature for this unit is between 5°C and 20°C (41°F and 68°F).
• Never discharge the battery fully.
• Charge after each use.
9
• Always charge at least once every 3-6 months if not in frequent use to prevent overdischarge.
Transportation of Lithium Batteries
• Always check all applicable local, national, and international regulations before transporting a
unit containing a lithium battery.
• Transporting an end-of-life, damaged, or recalled battery may, in certain cases, be specifically
limited or prohibited.
INSTRUCTIONS PERTAINING TO THE USB PORT
NOTICE:
• IMPORTANT: Some household USB-powered electronics will not operate with the USB port
provided with this device. Check the manual of the corresponding electronic device to confirm
that it can be used with this type of USB port.
• The USB port does not support data communication. It only provides power to an external
USB powered device. (5V DC/1A using the USB Port on the Spotlight. Make sure the rating of
equipment plugged into the USB Port does not exceed the amperage stated.)
• Do not attach USB hubs allowing connection of multiple personal electronic devices to the
USB port on the unit.
SAVE THESE
INSTRUCTIONS
INTRODUCTION
Congratulations on purchasing your new Stanley
®
Lithium LED Spotlight. Read this
Instruction Manual and follow the instructions carefully before using your new spotlight.
FEATURES
1. Rubber Bezel
7. USB Port (for use with USB Charging
2. Heat Sink
3. Swing-up Stand
8. USB Power Button
4. On/Off Trigger
9. Emergency Red Lens (Optional Accessory)
5. Pistol Grip Handle
10. USB Charging Cable
6. Battery/Charge Status LED Indicator
READING THE BATTERY/CHARGE STATUS LED
INDICATOR
The Battery/Charge Status LED Indicator is a translucent ring around the USB Port at the back of
the unit. It lights or flashes in three colors to indicate the following:
When Charging:
Green:
Battery is in a fully charged state.
Green (flashing):
Battery is in a high partially charged state.
Orange (flashing):
Battery is in a low partially charged state.
Red (flashing):
Battery needs to be recharged.
Red (flashing rapidly):
The battery of the unit is overheated due to extensive use or
recharging. The charging process will stop at this stage and will automatically resume after a
cool down period.
When Operating
(once the light has been turned on or the USB Power
:
Button has been pressed)
Green:
Battery is operating at full voltage.
Orange:
Battery is operating at partial voltage.
Red:
Battery is operating at low voltage and should be recharged or the built-in low voltage
protection will be activated and the unit will automatically shut down shortly.
Red (flashing rapidly):
The battery of the unit is overheated (due to extensive use or
recharging), or is too cold (the ambient temperature has dropped below –20°C). To avoid
damage, the unit should be shut off at this stage and allowed to either cool down or warm up
to normal operating temperatures before resuming use.
CHARGING/RECHARGING THE SPOTLIGHT
This unit is shipped in a partially charged state. Charge unit after purchase and BEFORE first use
until the Battery/Charge Status LED Indicator lights green.
Recharge after each use until the Battery/Charge Status LED Indicator lights green.
IMPORTANT: When the unit is not in use, we recommend that the battery is charged at least
every 3 to 6 months.
CAUTION –
TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• Never place the light face down on any surface when charging.
• Make sure the light and the USB port are turned off during recharging, as using these features
can slow the recharging process.
• Failure to keep the battery charged will cause permanent damage and result in poor
performance.
NOTE: The USB Power Button does not operate the light, only the USB Power Port. The light
cannot be charged when the USB Power Port is on. Make sure the USB Power Button is turned
off before charging.
Charging/recharging using the USB Charging Cable and a
Device with a USB Power Port (not supplied)
1. Make sure the On/Off Trigger and the USB Power Button are both turned off (the light is
not lit and the Battery/Charge Status LED Indicator inside the translucent ring around the
USB port at the back of the unit is not lit).
2. Insert the USB Charging Cable into the USB port on the light.
3. Insert the other end of the USB Charging Cable into a device's functional USB power
port. The Battery/Charge Status LED Indicator will light or flash in one of three colors (as
described in the "Reading the Battery/Charge Status LED Indicator" section) to indicate
the charging status.
4. Charge until the Battery/Charge Status LED Indicator lights green.
5. When charging is complete, disconnect the USB Charging Cable from the device's USB
power port and the light. Store the cable in a safe place.
OPERATING THE SPOTLIGHT
IMPORTANT: If the USB Power Button is pressed to turn on the USB Port when the unit is
operating in High light mode, the unit will switch automatically to Low light mode.
If the light's battery voltage is nearly low, the unit will switch automatically to Low light mode
even if High light mode has been selected.
If the light's battery voltage is low, the built-in low voltage protection will activate after a short
period of operation, then the unit will automatically shut down. Recharge the battery before
continuing use.
The On/Off Trigger turns the unit on and off, and is also used to choose either the high or low
brightness setting.
DO NOT OPERATE WHILE CHARGING.
Disconnect the charging cable, then select the light mode as follows:
• Press the On/Off trigger once to use the spotlight in its high (brightest) setting.
• Press the On/Off trigger again within 5 seconds to use the spotlight in its low (dimmest)
setting.
• Press the On/Off trigger a third time to turn the unit off.
OR
• Press the On/Off trigger once to use the spotlight in its high (brightest) setting.
• Press the On/Off trigger again after 5 seconds to turn the unit off.
Note:
The Battery/Charge Status LED Indicator will light in one of three colors (as described in the "Reading
the Battery/Charge Status LED Indicator" section) to indicate the battery status.
Using the Emergency Red Lens
The Emergency Red Lens snaps into place directly over the Rubber Bezel.
CAUTION –
• Never touch the Emergency Red Lens or place the light with an attached Red
Emergency Lens face down on any surface while it is operating.
• Never use the Red Emergency Lens on the spotlight if it is damaged.
• Always detach the Red Emergency Lens from the spotlight and store it properly when it is
not in use.
Using the Swing-up Stand
Lift the Swing-up Stand up, invert the unit and set it upon a flat, stable surface
for hands-free operation.
OPERATING THE LIGHT'S USB PORT
IMPORTANT: If the USB port is in use, the light will only operate in Low light mode.
The light's USB port provides 5 volts/1A of DC power to an external USB powered device.
1. Disconnect the charging cable and make sure the light is turned off.
2. Press the USB Power Button to power on the USB port. The Battery/Charge Status LED
Indicator will light or flash in one of three colors (as described in the "Reading the Battery/
Charge Status LED Indicator" section) to indicate the internal battery status.
3. Simply plug the USB device into the light's USB port and operate normally.
If a lithium battery
4. Press the USB Power Button again to turn off the USB port. Make sure the USB Power
Button is in the off position when the unit is being recharged or stored.
CARE AND MAINTENANCE
All batteries lose energy from self-discharge over time and more rapidly at higher temperatures.
When the unit is not in use, we recommend that the battery is charged at least every 3 to 6
months.
Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the
spotlight unit with a soft cloth.
There are no user-replaceable parts. Periodically inspect the condition of connectors and wires.
Battery replacement/disposal
BATTERY REPLACEMENT
The battery should last the service life of the unit. Service life is dependent on a number
of factors including but not limited to the number of recharge cycles, and proper care and
maintenance of the battery by the end user. Contact manufacturer for any information you
may need.
SAFE BATTERY DISPOSAL
Contains a lithium battery, which must be disposed of properly.
Recycling is required. Failure to comply with local, state and federal
regulations can result in fines, or imprisonment.
Please recycle.
WARNINGS:
• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to
prevent shorting (shorting can result in injury or fire).
• Do not expose battery to fire or intense heat as it may explode.
TROUBLESHOOTING
The Spotlight will not charge
• Check that the Spotlight and the USB port are turned off.
• Check that the USB Charging Cable is properly connected to the charging source and to the
Spotlight.
• The unit may have shut down to protect the battery from overheating after a long period
of operation or charging. Disconnect the USB charging cable from the spotlight. Allow the
spotlight to cool down for a period before resuming charging.
The Spotlight will not operate
• Make sure the On/Off Trigger has been pressed to turn the Spotlight on.
• The internal battery may be completely discharged. Charge the unit following the directions
given in this manual.
• If the ambient temperature is too hot or too cold the Spotlight will not operate.
Cable)
The Spotlight's USB Port will not operate
• Make sure the cable is disconnected from any live power source.
• Make sure the On/Off Trigger is turned off.
• Make sure the USB Power Button is pressed to turn the USB port on.
• Make sure the rating of equipment plugged into the light's USB port does not exceed 1A
continuous.
• The internal battery may be completely discharged. Charge the unit following the directions
given in this manual.
ACCESSORIES
Recommended accessories for use with this unit may be available from the manufacturer. If you
need assistance regarding accessories, please contact manufacturer at 1-877-571-2391.
The use of any accessory not recommended for use with this appliance could be hazardous.
TECHNICAL ASSISTANCE
For Customer Service or Technical Assistance, contact the manufacturer at 1-877-571-2391.
ONE-YEAR LIMITED MANUFACTURER'S WARRANTY
The manufacturer, Baccus Global LLC, warrants this product against defects in materials and
workmanship for a period of ONE (1) YEAR commencing from the date of retail purchase by
the original end-user purchaser or from the date of delivery of the good, whichever occurs later
("Warranty Period").
If there is a defect and a valid claim is received by the manufacturer within the Warranty Period,
the defective product can be replaced in the following ways: (1) Return the product to the
manufacturer for replacement. Proof of purchase may be required by manufacturer. (2) Return
the product to the retailer where product was purchased for an exchange (provided that the
store is a participating retailer). Returns to retailer should be made within the time period of
the retailer's return policy for exchanges only. Proof of purchase may be required. Please check
with the retailer for their specific return policy regarding returns that are beyond the time set
for exchanges.
This manufacturer's warranty does not apply to accessories, bulbs, fuses and batteries; defects
resulting from normal wear and tear, accidents; damages sustained during shipping; alterations;
unauthorized use; neglect, misuse, abuse; and failure to follow instructions for care and
maintenance for the product.
This manufacturer's warranty gives you, the original retail purchaser, specific legal rights and
you may have other rights which vary from state to state or province to province. This product
is not intended for commercial use. To register your product with the manufacturer, please visit
www.BaccusGlobal.com.
The photos in this manual may differ from the actual unit.
SPECIFICATIONS
Spotlight
Bulb:
Battery:
Input:
USB Output:
STANLEY
AND THE STANLEY
®
REGISTERED TRADEMARKS OF STANLEY BLACK +
DECKER INC. OR ONE OF ITS AFFILIATES, AND ARE
USED UNDER LICENSE.
TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
10 watt LED
Lithium, 3.7V DC
5V DC, 1A
5V DC, 1A
LOGO ARE
Imported by Baccus Global LLC,
®
225 NE Mizner Blvd., Suite 301, Boca Raton, FL 33432
www.baccusglobal.com 1-877-571-2391
RD072324
Need help?
Do you have a question about the FATMAX SL10LEDS and is the answer not in the manual?
Questions and answers