Table of Contents
Advertisement
Quick Links
Vibratory Plate Compactor
MODEL NUMBER :
SERIAL NUMBER :
Both model number and serial number may be found on the main
label. You should record both of them in a safe place for future use.
READ AND UNDERSTAND THE ENTIRE MANUAL BEFORE
Operator's Manual
CEDZG07
FOR YOUR SAFETY
OPERATING MACHINE
HAHN A SYN s.r.o.
Lelkova 186/4
747 21 Kravaře
CZECH REPUBLIC
info@hahn-profi.cz
Save This Manual for Future Reference
Original Instruction
Hahn & Sohn GmbH
Janahof 53
93413 Cham
Deutschland
hahn@hahn-sohn.de
Advertisement
Table of Contents
Related Manuals for Hahn & Sohn CEDRUS CEDZG07
Summary of Contents for Hahn & Sohn CEDRUS CEDZG07
- Page 1 Save This Manual for Future Reference Original Instruction Vibratory Plate Compactor Operator’s Manual MODEL NUMBER : CEDZG07 SERIAL NUMBER : Both model number and serial number may be found on the main label. You should record both of them in a safe place for future use. FOR YOUR SAFETY READ AND UNDERSTAND THE ENTIRE MANUAL BEFORE OPERATING MACHINE...
-
Page 2: Table Of Contents
avoid any trapped air or voids. It increases TABLE OF CONTENTS the load bearing capacity, decreases water seepage, prevents soil settlement, reduces Introduction swelling, contraction soil Specifications prevents frost damage. ideal compaction of granular soils, sands, gravel, Symbols crushed aggregate and mixed soils. Safety General Safety Rules These compactors are not intended... -
Page 3: Symbols
SYMBOLS SAFETY The rating plate on your machine may General Safety Rules show symbols. These represent important information about the product or instructions Understand your Machine on its use. Read and understand the operator’s manual and labels affixed to the machine. Learn its application and limitations as well as the Read these instructions for use specific potential hazards peculiar to it. - Page 4 Do not use the machine if the engine’s switch Never overfill fuel tank (there should be no does not turn it on or off. Any gasoline fuel above the upper limit mark). powered machine that can not be controlled Replace all fuel tank and container caps with the engine switch is dangerous and must securely and wipe up spilled fuel.
-
Page 5: Specific Safety Rules
If the machine should start to make an unusual Always operate the machine from behind, noise or vibration, immediately shut off the never pass or stand in front of the machine engine, disconnect the spark plug wire, and when the engine is running. check for the cause. -
Page 6: Contents Supplied
1.Plate Compactor Chassis with Engine and CONTENTS SUPPLIED Transmission 2. Handle The plate compactor comes partially assembled and is shipped in carefully packed carton. After 3.Paving Pad (Optional) all the parts have been removed from the carton, 4.Folding Wheels Kit (Optional) you should have: 5.Operator’s Manual &... -
Page 7: Assembly
Folding Wheels Kit (Optional) ASSEMBLY Following the assembly directions below, you will assemble the plate compactor in a few minutes. Handle 12x120 Φ12 2x11x35 Attach the wheel kit into the bracket of the engine base. Align the holes in the bracket with the holes in wheel kit. - Page 8 Paving Pad Kit (Optional) The transparent rubber Paving Pad allows to compact concrete paving slabs, stones, bricks and blocks silently and gently. M10 X 35 Attach the paving pad onto the base plate as shown. Align the holes in the Base Plate, Paving Pad and Clamp Plates, and secure it with 3 bolts M10x35 and lock washers.
-
Page 9: Know Your Machine
KNOW YOUR MACHINE Features and Controls Throttle Control Lift Handle Handle Air Cleaner Muffler Fuel Tank Belt Guard Oil Drain Hose Exciter Base Plate Fuel Valve Control The fuel valve opens and the engine switch to the OFF position stops closes the passage between the fuel tank and the engine. - Page 10 Oil Drain Hose Compactor Operation Adding fuel Fill the fuel tank as instructed in the separate Engine Manual packed with Plate Compactor. More detailed description of the engine operation and all related precautions and procedures can be found in the Engine Manual packed separately with the unit.
- Page 11 3.In operation, guide the machine, but let the Stopping Engine compactor do the work. Bearing down on the To stop the engine in an emergency, simply handle is unnecessary and causes shock turn the engine switch to the OFF position. absorber wear.
-
Page 12: Maintenance
Turn off engine. Engine must be cool. MAINTENANCE 2.Remove the belt guard to access the V-belt(s). Maintaining your compactor will insure long Check the condition of the V-belt(s). If life to the machine and its components. any V-belt is cracked, frayed, or glazed, it should be replaced as soon as convenient. - Page 13 Push engine toward the back of the plate by turning the adjustment bolts A to remove any slack in V-belt(s). Clutch pulley V-belt Exciter pulley 3. Slide the engine toward the front of plate and slip the old V-belt(s) off of the wheel pulley and install the new V-belt(s) in their place.
- Page 14 Exciter Lubrication The exciter housing is pre- serviced using Automatic Transmission Fluid Dextron III, Mercon, EXXON (ESSO) NUTO H-32 or its equivalent. Change fluid after 200 hours of operation. Let exciter cool before changing exciter oil. Remove bolt plug from top of exciter housing.
-
Page 15: Storage
STORAGE If the plate compactor will not be used for a period longer than 30 days, following the steps below to prepare your unit for storage. Drain the fuel tank completely. Stored fuel containing ethanol or MTBE can start to go stale in 30 days. -
Page 16: Lifting/Transporting
LIFTING/TRANSPORTING See technical data for the weight of the machine. To avoid burns or fire hazards, let engine cool before lifting / transporting machine or storing indoors. The unit must be transported in the upright position to prevent fuel from spilling. Do not lay machine on its side or top. -
Page 17: Trouble Shooting
TROUBLE SHOOTING Problem Cause Remedy 1. Attach spark plug wire securely to 1.Spark plug wire spark plug. disconnected. 2.Fill with clean, fresh gasoline. 2.Out of fuel or stale fuel. 3.Move throttle control lever to start 3.Throttle control lever not in position. -
Page 18: Parts Schedule
PARTS SCHEDULE OPTIONAL PLATE COMPACTOR... -
Page 19: Parts List
PARTS LIST Q'ty Q'ty Description Description Lifting Frame Weldment Bolt M8x25 Washer 12 Exciter Housing Spring Washer 12 Oil Seal FB30x42x6F Bolt M12x30 Bearing Cover - Left Bolt M8x40 Exciter Housing Gasket Nut M8 Bearing Cover - Right Engine Base Weldment Air Plug Screw Nut M8 Sealing Washer 14... - Page 20 Description Q'ty 68 Wheel Clamp Plate Paving Pad Nut M10 Washer 10 Bolt M10x35 Throttle Control Oil Drain Hose Handle Sleeve PLATE COMPACTOR...
Need help?
Do you have a question about the CEDRUS CEDZG07 and is the answer not in the manual?
Questions and answers