Table of Contents
Advertisement
Quick Links
Front Tine Tiller
OPERATOR'S MANUAL
Warning: The Engine Exhaust from this product contains chemicals known to
the State of California to cause cancer, birth defects or other reproductive harm.
Model# PTG1110
DO NOT RETURN TO STORE!
STOP
HAVE QUESTIONS OR NEED SERVICE?
866-591-8921
support@pulsar-products.com
Advertisement
Table of Contents
Related Manuals for Pulsar PTG1110
Summary of Contents for Pulsar PTG1110
- Page 1 Model# PTG1110 Front Tine Tiller OPERATOR’S MANUAL DO NOT RETURN TO STORE! Warning: The Engine Exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. STOP HAVE QUESTIONS OR NEED SERVICE? 866-591-8921 support@pulsar-products.com...
-
Page 2: Table Of Contents
Table of Contents Safety Information ........2 Assembly . -
Page 3: General Safety
Safety (continued) GENERAL SAFETY □ □ Do not put hands or feet near or under rotating parts. Keep If the equipment should start to vibrate abnormally, stop clear of discharge area at all times as the rotating tines the engine and check immediately for the cause. Vibration can cause injury. -
Page 4: Children Safety
Safety (continued) GENERAL SAFETY □ This tiller has a 2-Cycle engine. Make sure your fuel mixture □ Always be sure of your footing. A slip and fall can cause is 50 parts gas to 1 part oil. Failure to follow this instruction serious personal injury. - Page 5 Safety (continued) GENERAL SAFETY □ Do not modify engine. Before cleaning, repairing, or inspecting, make certain the tines and all moving parts have stopped. Disconnect the □ To avoid serious injury or death, do not modify engine in any spark plug wire and ground against the engine to prevent unintended starting.
-
Page 6: Pre-Assembly
Pre-Assembly PLANNING ASSEMBLY Place box on a level surface. Remove all items from box. Make sure all items listed on the package contents list are included and not damaged. TOOLS REQUIRED Funnel Safety goggles HARDWARE INCLUDED Hardware not shown to actual size. NOTE: Part Description... -
Page 7: Assembly
Assembly Assembling the Handles Assembling the Drag Stake NOTICE: This tiller is shipped without gasoline or oil in the engine. □ The drag stake is shipped with the point facing upwards. Fill up the gasoline and oil BEFORE operating your machine. To use for cultivating, remove detent pin, and turn the drag stake upside down so the point faces downward. - Page 8 Assembly (continued) Assembling the Tines □ Install the tines in turn as shown below and secure them Clevis and Cotter Pin. See Figure 3. Clevis pin Figure 6 Cotter pin WARNING: Make sure the tiller protective shield is Figure 3 installed in place before starting the machine.
-
Page 9: Operation
Operation Adding 50 Parts Gas to 1 Part Oil □ Stop engine and allow it to cool before refueling. □ Place the unit upright on the ground or on a sturdy bench and wipe away any debris from around the WARNING: Use extreme care when handling gasoline. - Page 10 Operation (continued) Controls and Features DRAG STAKE □ In hard compacted soil, it helps restrain the tiller's forward RECOIL STARTER motion. In looser soil, it controls how deeply the tines can dig into the ground. □ The recoil starter is attached to the right side of the upper handle.
-
Page 11: Pre-Start Inspection
Operation (continued) Pre-Start Inspection Starting the Cultivator COLD STARTS □ Make sure all safety guards are in place and all nuts and bolts are secure. □ Place the cultivator on a flat surface □ Check the fuel supply. Fill the fuel tank no closer □... -
Page 12: Restarting A Warm Engine
Operation (continued) RESTARTING A WARM ENGINE NOTICE: If the unit still doesn’t start, refer to the TROUBLESHOOTING section of this manual or: If you need assistance □ Place the cultivator on a flat surface. or have any questions, CALL TOLL FREE: 866-591-8921. □... -
Page 13: Wheel Height Adjustment
Operation (continued) Tilling Tips Wheel Height Adjustment □ The key to successful tilling is to begin with a shallow cut □ on the first pass, and then work an inch or two deeper on Remove the detent pin. each successive pass. □... -
Page 14: Maintenance
Maintenance Always observe safety rules when performing any □ Lubricate the wheels at least once a season with light oil (or maintenance. motor oil). If wheels are removed for any reason, lubricate surface of the axle bolt and inner surface of the wheel with light oil. -
Page 15: Maintenance Schedule
Maintenance (continued) MAINTENANCE SCHEDULE □ Your tiller has been designed and produced by the industry’s leading manufacturer of outdoor power equipment to provide you with years of reliable operation. Keeping your tiller in top running condition will prolong its life, and help you obtain optimum performance. □... -
Page 16: Air Filter
Maintenance (continued) AIR FILTER Never clean filter in gasoline or other WARNING: flammable solvents. Turn off ignition switch, and disconnect WARNING: the spark plug before performing maintenance except for carburetor adjustments. Reconnect the spark plug □ Add a drop of thin oil to the filters and replace it. wire after the service is done. -
Page 17: Care, Cleaning And Storage
Care, Cleaning and Storage Follow the steps below to prepare your tiller for storage. SPARK PLUG CONTINUED □ Protect wheels and axles from rust by removing the lockpin To inspect or replace the spark plug: and sliding the wheel off the hub. □... -
Page 18: Troubleshooting
Troubleshooting Problem Cause Solution □ □ Engine will not start. Ignition Switch in the “OFF” position. Move ignition switch to the ON position. □ □ Engine flooded. See Starting a Flooded Engine in OPERATION section. □ □ Fuel Tank empty. Fill tank with correct fuel mixture. -
Page 19: Service Parts
Service Parts Part Description Quantity Part Description Quantity Tine Recoil Wheel Air cleaner Assy Tine Wheel Air Filter Assembly Recoil...
Need help?
Do you have a question about the PTG1110 and is the answer not in the manual?
Questions and answers