Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for EVERCROSS EK6
Summary of Contents for EVERCROSS EK6
- Page 1 EU V1.2.2 User Manual...
-
Page 2: Product Overview
PRODUCT OVERVIEW 19 Seat Tube 1 LCD Display 13 Chain 7 Front Fork 20 Saddle 2 Handlebar grip 14 Transmission 8 Disc Brake 3 Brake Lever 15 Motor 9 Folder 4 Headlight 16 Rear Rack 10 Pedal 5 Tire 17 Tail Light 11 Chainring 6 Disc brake pad 18 Seat Tube Clip... - Page 3 ASSEMBLY Before beginning the assembly process, please conduct a thorough inspection of the packaging to ensure that all necessary components and accessories are included. If you identify any items that are missing or damaged, please contact us promptly. PARTS DESCRIPTION 5.Wheel Reflectors 1.Seat&post 6.Front wheel quick release...
- Page 4 ASSEMBLY - VEHICLE UNFOLD 1.Open the telescopic adjustment 2.Insert the telescopic standpipe, adjust the buckle of the foldable standpipe and desired height, and press the adjustment buckle insert the telescopic standpipe in the in the direction of the arrow in the figure. direction of the arrow.
- Page 5 3.Stand up the foldable standpipe in 4.After confirming that the quick release plug is the direction of the arrow in the figure inserted, lift the pull rod and wrench in the direction of and close it. the arrow in the figure. 5.Press down the folding wrench in the direction of the arrow in the figure to lock the foldable standpipe.
- Page 6 ASSEMBLY - FRONT FENDER 2.Put on the nut. 3.Tighten the screws with 1.Pre-install the headlight and 16-in-1 Tool #5 allen wrench fender on the front fork with the and #10 socket hand. headlight fixing screw. 4.Remove the mudguard stick fixing 5.Fix the front mudguard sticks in the screws pre-installed on the left and right corresponding screw holes of the front...
- Page 7 ASSEMBLY - FRONT WHEEL 1.Loosen the nut in the picture with the 16-in-1 Tool #15 open-end wrench from the kit, and remove the fork leg protection shaft. 2.Unscrew the nut of the quick release lever, take out the gasket, sleeve and nut on one side. EN-12...
- Page 8 4.Insert the sleeve. 3.Insert the quick release lever. Note: Disc brake pads 5. Insert the front wheel into the front fork need to be put into the disc dropout and lock the screws. brake. Note: During this process, ensure that the front wheel is in the center of the front fork tube.
- Page 9 6.Insert two gaskets and nuts in sequence 7.Use a No. 15 wrench to tighten the nuts on both sides at the same time. Note: If the gasket is as shown in the picture, please adjust the position of the gasket until it ）...
- Page 10 ASSEMBLY - SEAT 1.Pull the quick release lever of the seat post 2.Insert the seat post and adjust it to the desired clamp in the direction shown in the figure. height (note: the depth of the inserted seat post should exceed the safety mark). 3.Press the quick release lever according to the direction shown in the figure.
- Page 11 ASSEMBLY - WHEEL REFLECTORS Put the wheel reflector on the reserved fixed position of the wheel hub, and lock the two screws "1" and "2" with a Phillips screwdriver. The front and rear wheel reflectors operate in the same way. EN-16...
- Page 12 ASSEMBLY - REAR FENDER STICK 1.Use the No. 4 Allen wrench in the 16-in-1 tool to remove the fixing screws and washers of the fender sticks pre-installed on the left and right sides of the frame, as shown in the figure. 2.Insert the stick, then tighten the fixing screws and washers on both sides, as shown in the figure.
- Page 13 ASSEMBLY - PEDAL - Left pedal installation: The letter "L" on the pedal axis indicates the left pedal. Rotate the pedal axis counterclock- wise by hand to screw it into the crank arm on the left side, and then use a 16-in-1 Tool #15 open-end wrench to tighten it counterclock- wise.
- Page 14 REMOVE & INSTALL THE BATTERY ASSEMBLY - BATTERY REMOVAL & INSTALLATION 1.Find the seat 2.Turn the seat handle and pull it up. upwards to flip. 4.Pick up the 3.Use the key to turn to battery handle the "PUSH" position to to remove the take out the battery.
- Page 15 ASSEMBLY - BATTERY INSTALLATION 1.Find the seat handle and 2.Align the notch at the pull it up and turn the seat bottom of the battery with upwards to flip. the slide. 4.Press down to 3.Put the restore the seat. battery down. EN-20...
-
Page 16: Contenu Du Colis
15 mm Vérifiez soigneusement le contenu de l'emballage, si quelque chose manque ou est endommagé, veuillez contacter le service client EVERCROSS pour obtenir de l'aide. Remarque : Veuillez conserver l'emballage extérieur du produit au cas où vous auriez besoin de renvoyer le vélo à...
Need help?
Do you have a question about the EK6 and is the answer not in the manual?
Questions and answers