Advertisement
Quick Links
SUPA PEG
A U S T R A L I A
SUPA-WING AWNING (DELUXE)
Awning Setup/ Fold Away Instructions
Thank you for your purchase of the Australian made and designed SUPA-WING AWNING
Please follow these few simple step by step instructions to make setting up your
SUPA-WING AWNING (DELUXE) simple to use and to improve the life span of the
**PLEASE NOTE** For winds over 5 knots a second person maybe required to assist for the
Contents
• Mounting Bracket Set (2 Brackets) - 13mm Spanner
• (additional included for 3 & 3.5m) - Stainley knife (for cutting roof rack rubber)
• 10 x 225mm Galv Tent Pegs (additional included for 3 & 3.5m)
• 5 x Quick Release straps (additional included for 3 & 3.5m)
• Peg Bag
• 1 x Side Spreader Rail and 1 x Roof Spreader Rail (additional included for 3 & 3.5m)
(DELUXE).
product
following steps, if the tie down straps are not used **
& Tools Required
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for SUPA PEG SUPA-WING DELUXE
Summary of Contents for SUPA PEG SUPA-WING DELUXE
- Page 1 SUPA PEG A U S T R A L I A SUPA-WING AWNING (DELUXE) Awning Setup/ Fold Away Instructions Thank you for your purchase of the Australian made and designed SUPA-WING AWNING (DELUXE). Please follow these few simple step by step instructions to make setting up your SUPA-WING AWNING (DELUXE) simple to use and to improve the life span of the product **PLEASE NOTE** For winds over 5 knots a second person maybe required to assist for the following steps, if the tie down straps are not used ** Contents & Tools Required • Mounting Bracket Set (2 Brackets) - 13mm Spanner • (additional included for 3 & 3.5m) - Stainley knife (for cutting roof rack rubber) • 10 x 225mm Galv Tent Pegs (additional included for 3 & 3.5m) • 5 x Quick Release straps (additional included for 3 & 3.5m) • Peg Bag • 1 x Side Spreader Rail and 1 x Roof Spreader Rail (additional included for 3 & 3.5m)
- Page 2 SUPA PEG A U S T R A L I A May require professional installation with some roof racks. Fittings suited to most roof rack brands. STEP ONE STEP TWO STEP THREE Check contents and separate for Remove any end caps if required Pull back rubber on extrusion to install (use short bolts for brackets) to expose to channel in the roof expose slot. (check the channel nut rail. slides in first) STEP FOUR STEP FIVE STEP SIX Cut or remove rubber extrusion Bolt the channel nuts to the Slide the bracket into the roof rack back so that the mounting plate brackets making sure to use both channel will fit to the end. the flat and spring washers STEP SEVEN STEP EIGHT STEP NINE Slide bracket into position and Do the same for the other side and...
- Page 3 SUPA PEG A U S T R A L I A May require professional installation with some roof racks. AWNING INSTALLATION STEPS (CONT) STEP TEN STEP ELEVEN STEP TWELVE Slide 2 bolts into the top and 2 into Roughly line up the bolts to Locate the awning onto the bolts the bottom channels of the awning and apply a small amount of the where the awning brackets will extrusion grease to each bolt (will prevent be on the vehicle nuts from seizing) STEP THIRTEEN STEP FOURTEEN STEP FIFTEEN Put the nyloc nuts onto each of the Slide the awning into position and Ready to go. bolts, tighten slightly so the awning tighten Regularly check that all bolts are extrusion still slide tightened and in good condition.
- Page 4 SUPA PEG A U S T R A L I A SUPA-WING AWNING (DELUXE) : Setup 1. Park at the proposed site you wish to setup, make sure you have enough clearance on the side and rear of the vehicle for the awning to fold out and expand 2. The Site should be level or close to it. If on a slight slope, face the awning down the slope as to prevent any wind getting under the awning causing it to lift 3. Remove the supplied poles, pegs and strap kit from the awning bag 4. If setting up by yourself, it would be advised to roughly pace out and peg down each of the straps to hook onto the ends of the awning arms as it is swung around for setting up. 5. Tie one of the straps to the driver’s side front roof rack (or passenger side for a right hand side awning) and bring to the back of the vehicle (or the strap can be pegged down at the rear of the vehicle) 6. Peg down the long strap at the front of the vehicle on the passenger side to where roughly the awning will extend to (an alternative option is to attach the Strap to your front bull bar if one is available) **PLEASE NOTE** For winds over 5 knots a second person maybe required to assist for the following steps, if the tie down straps are not used ** 7. Unzip the tonneau bag and fold the bag over the awning...
- Page 5 SUPA PEG A U S T R A L I A 8. Undo all Velcro straps holding the canvas and aluminium arms (remembering to support the arms once unstrapped) 9. Roll the canvas out, holding the outside arm, slowly fold the awning around to 270º (*** second person will need to hold the middle arm to prevent the awning from lifting in windy conditions) 10. As you go along expanding the awning arms out, fold out each of the awning legs and extend out to your rough desired height If setting up using the supplied straps (for windy conditions) connect a strap to each of the awning arms as you walk to awning around to the 270 degrees. 11. Once folded out to the rear of the vehicle, attach the strap to the eye at the end of the rear arm, tighten slightly to bring square off the awning extrusion 12. Fold out the front awning arm (the arm will be inside the main aluminium track of the awning) Extend out the front of the awning and fold down the supporting leg to your desired height (if using the tie down strap connect this now, 13. Attach the pegged down strap to the front awning pole and loosely tighten 14. Adjust the height and square up the awning. If being left unattended or it is raining, lower the...
- Page 6 SUPA PEG A U S T R A L I A 15. Tighten up both tie down straps a. (2.5m, 3m or 3.5m versions only) Connect Short Spigot spreader pole to the 1 and 2 poles (1 pole is the one closest to the front of the vehicle) To connect the pole, line up the...
-
Page 7: Care Instructions
SUPA PEG A U S T R A L I A 6. Roll up the canvas as tightly as possible and tie off with the remaining Velcro straps, undo the front Velcro strap and retie it to include the canvas and awning arms 7. Fold over the tonneau bag and zip it up, pack away pegs and straps in the canvas peg bag And you’re done! Don’t forget to clean up your site of any rubbish or debris to help keep this country beautiful. If the awning is packed up damp. Be sure to put up again and soon as there is dry weather to dry the canvas out. Any abuse or neglect of awning can result in voiding the Warranty. Enjoy your SUPA-WING AWNING (DELUXE), any problems regarding this product please contact your local reseller or email us at info@supapeg,com.au Check out our Supa Peg Youtube channel for more infomation on setup tips https://www.youtube.com/channel/UC2ZOHKkXi7gtTj8T9zbcMzQ Made by SUPA-PEG Australia, 100% Australian made and owned. CARE INSTRUCTIONS 1. As this is a stitched canvas product it will need to be wet and dried a few times to ensure no stitching leaks will occur 2. If leaks were to continue a pure bees wax can be applied to the stitch seams to water proof these areas 3. If the awning is packed up damp. Be sure to put up the awning as soon as there is dry weather to dry the canvas out to prevent mould or mildew growing. - Page 8 SUPA PEG A U S T R A L I A PRODUCT WARRANTY TERMS & CONDITIONS PERIOD OF WARRANTY In addition to any warranties or conditions implied by the Trade Practices Act, 1974 (as amended) or any other Statute or Regulation, we warrant this product against defective workmanship and faulty material under normal use for twenty- four (24) months from the date of purchase (the Warranty).
Need help?
Do you have a question about the SUPA-WING DELUXE and is the answer not in the manual?
Questions and answers