Advertisement
Quick Links
SUPA PEG
A U S T R A L I A
STAND EASY DELUXE AWNING
Awning Setup/ Fold Away Instructions
Thank you for your purchase of the Australian made and designed
Please follow these few simple step by step instructions to make setting up your
STAND EASY DELUXE AWNING simple to use and to improve the life span of the product
**Please note: two people are required to set up and pack in winds over 5 knots or for unexpected
Contents
• Mounting Bracket Set (2 Brackets) ) - 13mm Spanner
• 4 x 225mm Galv Tent Pegs Pegs - Stainley knife (for cutting roof rack rubber)
• Peg Bag
2 x Quick Release straps
•
STAND EASY DELUXE AWNING.
wind gusts**
& Tools Required
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for SUPA PEG STAND EASY DELUXE
Summary of Contents for SUPA PEG STAND EASY DELUXE
- Page 1 SUPA PEG A U S T R A L I A STAND EASY DELUXE AWNING Awning Setup/ Fold Away Instructions Thank you for your purchase of the Australian made and designed STAND EASY DELUXE AWNING. Please follow these few simple step by step instructions to make setting up your STAND EASY DELUXE AWNING simple to use and to improve the life span of the product **Please note: two people are required to set up and pack in winds over 5 knots or for unexpected wind gusts** Contents & Tools Required • Mounting Bracket Set (2 Brackets) ) - 13mm Spanner • 4 x 225mm Galv Tent Pegs Pegs - Stainley knife (for cutting roof rack rubber) • Peg Bag 2 x Quick Release straps •...
- Page 2 SUPA PEG A U S T R A L I A May require professional installation with some roof racks. May require professional installation with some roof racks. Fittings suited to most roof rack brands. STEP ONE STEP TWO STEP THREE Check contents and separate for Remove any end caps if required Pull back rubber on extrusion to install (use short bolts for brackets) to expose to channel in the roof expose slot. (check the channel nut rail. slides in first) STEP FOUR STEP FIVE STEP SIX Cut or remove rubber extrusion Bolt the channel nuts to the Slide the bracket into the roof rack back so that the mounting plate brackets making sure to use both channel will fit to the end. the flat and spring washers STEP SEVEN STEP EIGHT STEP NINE Slide bracket into position and...
- Page 3 SUPA PEG A U S T R A L I A AWNING INSTALLATION STEPS (CONT) STEP TEN STEP ELEVEN STEP TWELVE Slide 2 bolts into the top and 2 into Roughly line up the bolts to Locate the awning onto the bolts the bottom channels of the awning and apply a small amount of the where the awning brackets will extrusion grease to each bolt (will prevent be on the vehicle nuts from seizing) STEP THIRTEEN STEP FOURTEEN STEP FIFTEEN Put the nyloc nuts onto each of the Slide the awning into position and Ready to go. bolts, tighten slightly so the awning tighten Regularly check that all bolts are extrusion still slide tightened and in good condition. If you have any issues with installation and or your rack design is different from the standard...
- Page 4 SUPA PEG A U S T R A L I A STAND EASY DELUXE AWNING STAND EASY DELUXE Awning: Setup 1. Park at the proposed site you wish to setup, make sure you have enough clearance on the side of the vehicle for the awning to expand out 2. The Site should be level or close to it. If on a slight slope, face the awning down the slope as to prevent any wind getting under the awning causing it to lift 3. Unzip the Tonneau bag and fold the bag over the awning a. If the optional extension kit has been purchased, be careful when opening the bag, place the extension kit aside 4. If putting the awning up in windy conditions with a single person, the supplied quick release straps should be pegged down roughly 2.5m out from the ends of the awning. Have the ties at arms reach for the next steps. Undo all Velcro ties holding the canvas and aluminium extrusion together 5. Let the canvas drop down, carefully pull out the awning all the way out to have fully stretched out (two people maybe required if it is too heavy or too windy to hold) 6. While holding the awning stretched out, fold out the aluminium legs on the front section and extend out to the required height, let the legs take the weight of the extrusion maintaining tension on the canvas.
- Page 5 SUPA PEG A U S T R A L I A 7. Fold out the aluminium arms from the rear extrusion and extend out, locate the spigot pin into the inside hole of the two holes available, repeat other side. Be careful when folding out the arms as to not tear or rip the canvas 8. Tension pole arms to get the canvas tight and even on both sides, tie down the aluminium arms with the Velcro straps on the canvas a. (3500m versions) Insert roof support poles into the track on the vehicle by locating the spigot in the hole on the track and extending out to the front extrusion, lock off the pole and tie down with the Velcro ties. 9. Adjust the height of the poles and level out the awning. If being left unattended or it is raining, lower the pole height to allow for water run off. 10. Cross peg the tent pegs supplied into the folding foot plates (for beach camping an optional beach tie down kit should be used to hold down the awning) If using the supplied straps, they can be removed now once the feet are pegged down. If purchased the optional roof/wall extension can be put on now 1. End cap on the front of one side of the extrusion needs to be drilled out to 8mm into the sail track on the bottom (front) for the extension canvas piece to slide into **it is the users choice on which side the hole is drilled into (only drill one side only)** 2. Slide the extension piece into the sail track of the front aluminium extrusion, slide all the way to the end of the track (careful not to tear the fabric 3.
- Page 6 SUPA PEG A U S T R A L I A 6. Put the ropes over the spigots and tighten, adjust the pole height as necessary STAND EASY DELUXE Awning: Packing Away **Please note: two people maybe required to set up and pack in winds over 5 knots or for unexpected wind gusts or use the tie down strap method to hold the awning** To pack the Stand Easy Deluxe Awning away, in reverse order repeat steps 10 through to 5 as per the setup instructions. 1. Locate the plastic tongues on the end of the extrusion into the opposite side 2. Lock off with the centre Velcro tie a. (3.5m version) Tie the roof support poles to the centre Velcro strap 3. Straighten up the canvas and neatly roll up 4. Tie off the canvas with the two Velcro ties a. (Optional roof extension) Place inside the bag before zipping up 5. Place tent pegs in the Tonneau bag, zip up the awning bag And you’re done! Don’t forget to clean up your site of any rubbish or debris to help keep this country beautiful.
-
Page 7: Care Instructions
SUPA PEG A U S T R A L I A CARE INSTRUCTIONS 1. As this is a stitched canvas product it will need to be wet and dried a few times to ensure no stitching leaks will occur 2. If leaks were to continue a pure bees wax can be applied to the stitch seams to water proof these areas 3. If the awning is packed up damp. Be sure to put up the awning as soon as there is dry weather to dry the canvas out to prevent mould or mildew growing. 4. Please note if any mould or mildew was to form on your awning this can be removed with clean water and a soft brush (do not use any chemicals) the canvas is both rot and mildew resistant which means it will not imbed into the canvas 5. Aluminium pole maintenance – the anodised material is very tough from most water and salt environments, however to keep them working perfectly all sections should be hosed down and dried with a clean cloth a. If the twistlock poles continue to spin and do not grip and simple adjustment can be made by pulling the inner out and stretching out the c-clip section of the cam and putting back together, this will ensure the cam will grip to the outer tube 6. As this is an Australian made product all components can be replaced and canvas can be repaired (depending on severity) PRODUCT WARRANTY TERMS & CONDITIONS... - Page 8 SUPA PEG A U S T R A L I A PERIOD OF WARRANTY In addition to any warranties or conditions implied by the Trade Practices Act, 1974 (as amended) or any other Statute or Regulation, we warrant this product against defective workmanship and faulty material under normal use for twenty- four (24) months from the date of purchase (the Warranty).
Need help?
Do you have a question about the STAND EASY DELUXE and is the answer not in the manual?
Questions and answers