Advertisement
Quick Links
LEAKSTOPPER 1 WATER LEAK DETECTION ALARM PANEL INSTALLATION AND OPERATION MANUAL
Fault monitoring
(continuously monitors the cables/sensor tape/probes
connected for breaks in continuity)
Green - All OK
Red - Fault Detected
Alarm status light
Off - All OK
Red Flashing - Leak Detected
Power On
Green - ON
Power Off
No Light
Power Fail
illuminates to indicate
running on battery
backup
Alarm Test
illuminates when
test button pressed
Mute
Alarm Test
Button
Button
(press to silence the audio alarm)
(press to ensure that the LED
lights are functioning correctly)
Helpline Telephone: 0330 1595933
Installation and Operation manual - LeakStopper1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for EnviroTech Alarms LEAKSTOPPER 1
Summary of Contents for EnviroTech Alarms LEAKSTOPPER 1
- Page 1 LEAKSTOPPER 1 WATER LEAK DETECTION ALARM PANEL INSTALLATION AND OPERATION MANUAL Fault monitoring (continuously monitors the cables/sensor tape/probes connected for breaks in continuity) Green - All OK Red - Fault Detected Alarm status light Off - All OK Red Flashing - Leak Detected...
-
Page 2: Technical Specification
Product Overview: The LeakStopper 1 is a water leak detection alarm panel designed to notify that a leak has occurred. Each alarm panel has the capability to connect to sensor tape, sensor probes and/or sensor pads. The LeakStopper 1 has 2 common alarm output relays and a battery back up as standard. - Page 3 ENVIROTECH ALARMS - LEAKSTOPPER 1 - INSTALLATION INSTRUCTIONS - VERSION 2.0 Sensor Tape Applications: Sensor Tape The sensor tape used with the LeakStopper 1 water leak detection alarms has Under raised floors been specifically designed to detect the presence of water at any point along its’ length.
- Page 4 ENVIROTECH ALARMS - LEAKSTOPPER 1 - INSTALLATION INSTRUCTIONS - VERSION 2.0 Sensor Probe Probe Overview: Applications: The sensor probe is a height adjustable water leak detection sensor for use in areas Plantrooms susceptible to leaks. It’s contained in a rigid...
- Page 5 ENVIROTECH ALARMS - LEAKSTOPPER 1 - INSTALLATION INSTRUCTIONS - VERSION 2.0 Sensor Pad Sensor Pad Overview: Applications: The sensor pad is ideal for using in drip trays that have been installed under areas vulnerable to water leaks or equipment Comms Rooms...
- Page 6 ENVIROTECH ALARMS - LEAKSTOPPER 1 - INSTALLATION INSTRUCTIONS - VERSION 2.0 In-line tee sensor Applications: The in-line tee sensor has been designed to go into the over flow pipes on break tanks, Water tanks toilet cistern and header tanks. The sensor...
- Page 7 ENVIROTECH ALARMS - LEAKSTOPPER 1 - INSTALLATION INSTRUCTIONS - VERSION 2.0...
- Page 8 ENVIROTECH ALARMS - LEAKSTOPPER 1 - INSTALLATION INSTRUCTIONS - VERSION 2.0 Installing the sensor tape Notes: 1. Always connect the “End of Line” connector into the end of the sensor tape. 2. Do not run the sensor tape against anything conductive.
- Page 9 Installing the intelligent sensor probe/junction box The intelligent sensor probe/junction box can be used with the LeakStopper 1 alarm when there are longer cable runs required. It is not advised to run combined cable lengths (connection cable and sensor tape) over 100m using the standard junction boxes.
- Page 10 Black Common Connecting an SMS Dialler It is possible to connect the LeakStopper 1 alarm panel to an SMS dialler that will send a text message should a leak occur. NOTE: Please do not use the same connections that have been used for the valve.
- Page 11 Connecting to a Beacon/Sounder It is possible to connect the LeakStopper 1 alarm panel to a beacon, a sounder or a beacon/sounder. The power and switching for any of these are taken directly from the alarm panel as shown below.
-
Page 12: Troubleshooting Guide
ENVIROTECH ALARMS - LEAKSTOPPER 1 - INSTALLATION INSTRUCTIONS - VERSION 2.0 Connecting to a BMS Common Alarm Relay (1) or (2) To BMS using a normally open connection. Contact will close on alarm NOTE: Please do not use the same connections that have been used for the valve.
Need help?
Do you have a question about the LEAKSTOPPER 1 and is the answer not in the manual?
Questions and answers