Related Manuals for Topex TX032
Summary of Contents for Topex TX032
- Page 1 SKU:TXHD20V032 TX032 OWNER'S MANUAL 20V Cordless Drill & Impact Driver Set Thank you for buying this 20V Cordless Drill & Impact Driver Set Please read this manual carefully before using the product.
-
Page 2: Description Of Symbols
DESCRIPTION OF SYMBOLS GENERAL POWER TOOL SAFETY WARNINGS WARNING Volts Hertz Read all safety warnings and all instructions. Failure to follow the warnings and instructions may Alternating current millimeters result in electric shock, fire and/or serious injury. Revolutions per No load speed Save all warnings and instructions for future reference minute The term “power tool’’... - Page 3 d. Store idle power tools out of the reach of children and 3. PERSONAL SAFETY do not allow persons unfamiliar with the power tool or a. Stay alert, watch what you are doing and use common these instructions to operate the power tool. Power tools sense when operating a power tool.
-
Page 4: Hammer Drill Safety Warnings
– it is tilted in the workpiece HAMMER DRILL SAFETY WARNINGS – it has pierced the workpiece SAFETY INSTRUCTIONS FOR ALL OPERATIONS – the product is overloaded ■ Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss. ■... -
Page 5: Impact Driver Safety Warnings
IMPACT DRIVER SAFETY WARNINGS IMPACT DRIVER SAFETY WARNINGS BATTERY WARNINGS BATTERY WARNINGS 1. The battery pack is not fully charged out of the carton. ■ The product is not intended for use by persons (including First read the safety instructions and then follow the children) with reduced physical, sensory or mental charging notes and procedures. - Page 6 36. Do not use the cordless tool or the battery charger near vapours and inflammable liquids. 23. Do not use the supplied battery charger to charge other cordless tools. Only charge TOPEX rechargeable batteries with an TOPEX Charger. 24. The battery pack may become warm during use.
-
Page 7: Specifications
CORDLESS HAMMER DRILL SPECIFICATIONS Torque ( N.m) Max Voltage ( v=) Battery type Lithium-ion No-load speed ( rpm ) 0-350/0-1400 Max Chuck Size ( mm ) Torque Setting 21+1+1 Charger input ( V ) 100-240 Frequency ( Hz) 50-60 Allowable temperature (°c ) 0-50 Charge time ( h ) SETUP &... -
Page 8: Operation
2. FITTING ACCESSORIES Removing A Drill Bit WARNING WARNING! Ensure the tool is switched off and the battery is removed before performing any of the following tasks. Installing A Drill Bit 1. Rotate the chuck collar anti-clockwise to open the chuck WARNING WARNING! Do not handle accessories without gloves as they are sharp &... - Page 9 2. Adjust the torque by rotating the torque collar to the desired 2. Release the trigger to stop drilling. setting. Speed Control Note: Selecting a higher torque setting will allow the drill The gear selector controls the speed of the drill. First gear to use more torque to drive the screw in or out.
-
Page 10: Troubleshooting
Note: TOPEX will not be responsible for any damage or situations: injuries caused by repair of the tool by an unauthorised person or by mishandling. - Page 11 IMPACT DRIVER SETUP & PREPARATION 1. FITTING THE BATTERY Installing The Battery Pack 1. Slide the battery into the tool base until it clicks into place. Removing The Battery Pack 1. Hold down the battery release button. 1 Quick Release Chuck 2 Tri-Beam LED Light 3 Variable Speed Trigger 4 Forward/ Reverse Lever...
- Page 12 2. ATTACHING ACCESSORIES OPERATION WARNING 3. CONTROLS WARNING! Ensure the tool is switched off and the Variable Speed Trigger battery is removed before performing any of the 1. To start the driver, squeeze the variable speed trigger. following tasks. Inserting & Removing Accessories 1.
-
Page 13: Charging A Battery
5 The charger LED will illuminate green once the battery CHARGING A BATTERY is fully charged. CAUTION: the charger for this product should be protected by a residual current device (rated at 30ma or less). The purchased battery will be shipped in a low charge condition, and requires charging prior to use. - Page 14 TROUBLESHOOTING MAINTENANCE LED lights do not illuminate on charger WARNING! Always ensure the tool has completely stopped and the battery is removed prior to any Check the charging adaptor is securely plugged into the maintenance. wall out let. Check the battery is firmly connected to the charging •...
-
Page 15: Caring For The Environment
CARING FOR THE ENVIRONMENT Power tools that are no longer usable should not be disposed of with household waste but in an environmentally friendly way. Please recycle where facilities exist. Check with your local council authority for recycling advice. Recycling packaging reduces the need for landfill and raw materials. - Page 16 Contact: support@topto.com.au...
Need help?
Do you have a question about the TX032 and is the answer not in the manual?
Questions and answers