Table of Contents
Advertisement
Quick Links
NEOTAP TOUCH (R)
Hot, Cold, Sparkling Underbench Unit
INSTALLATION AND OPERATION GUIDE
Please read these instructions completely before operating this unit
+ 6 4 0 9 6 3 6 - 7 0 7 0 | W W W . S P R I N G N Z . C O . N Z | S A L E S @ S P R I N G N Z . C O . N Z
CONTENTS
1
2
3-4
5
6
7-8
9
10
11
12
13
14
Advertisement
Table of Contents
Troubleshooting
Subscribe to Our Youtube Channel
Related Manuals for Spring NEOTAP TOUCH
Summary of Contents for Spring NEOTAP TOUCH
-
Page 1: Table Of Contents
NEOTAP TOUCH (R) Hot, Cold, Sparkling Underbench Unit INSTALLATION AND OPERATION GUIDE CONTENTS Preface/Parts Piping Installation - Diagram Piping Installation - Instructions Co2 Bottle - Installation Hot Water Operation - Underbench Neotap Faucet - Functions Neotap Faucet - Troubleshooting Push Lock Fitting & Plumbers Delight Installation... -
Page 2: Preface/Parts
PREFACE/PARTS Before using this machine, we advise you to read this manual thoroughly. Please follow the instructions to ensure proper operation and the lasting of the machine Top Cover Brass Tee Off Valve Regulator NEOTAP - Hot, Cold, Sparkling Faucet Co2 Bottle (Plumbers Delight) Indicating Panel... -
Page 3: Piping Installation - Diagram
PIPING INSTALLATION - DIAGRAM Neotap Faucet One way tee valve Hot Water Tube - Grey (Friction fit) Hot Water Outlet Wiring loom Co2 Bottle Co2 Inlet Water Inlet Cold water Outlet Brass Tee off KDF50 Valve (Directional Flow.Flush out black carbon (Directional flow) (Plumbers dust before connecting to the machine) -
Page 4: Piping Installation - Instructions
PIPING INSTALLATION We recommend the instructions specified in this guide be followed in sequence by a qualified tradesperson to an existing potable water supply for successful installation When installing please ensure the unit is easily accessible for service and maintenance This Neotap has a 24 month back to base warranty from purchase, but this may be voided if unsatisfactory installation results in damage to the unit. - Page 5 PIPING INSTALLATION 14. Open gas bottle by turning the main bottle valve anticlockwise + 6 4 0 9 6 3 6 - 7 0 7 0 | W W W . S P R I N G N Z . C O . N Z | S A L E S @ S P R I N G N Z . C O . N Z...
-
Page 6: Co2 Bottle - Installation
Co2 BOTTLE - INSTALLATION 1. Ensure the Co2 bottle is connected firmly to the regulator and the Co2 tube is fitted correctly. 2. Slowly turn the dial on the regulator clockwise until the gauge reads 3BAR (Note: If you want to reduce the pressure you must first turn the dial anticlockwise and then vent to relieve existing pressure. -
Page 7: Hot Water Operation - Underbench
HOT WATER OPERATION - UNDERBENCH 1. Press the HOT button on the Faucet. Make sure the water is flowing before turning on the HOT power switch at the rear of the unit (This will ensure the HOT tank in the unit is full before turning on the element to prevent it burning out) 2. -
Page 8: Eco Mode Display
NEOTAP FAUCET - SYMBOLS ECO MODE DISPLAY Eco-mode is designed to save wasting unnecessary power when the unit is not in use. The Neotap will shut down the heating function after 1 minute when the sensor detects the ambient light in the room has been shut off. - Page 9 NEOTAP FAUCET - COLD AMBIENT INSTRUCTIONS SPARKLING COLD Turn on the COLD switch at the rear of the unit Leave to cool for 40 minutes Press the COLD button for Chilled water Please wait at least 2 seconds after the HOT button is released before pressing for Chilled or Ambient water The water will stop flowing after 1 minute.
-
Page 10: Neotap Faucet - Troubleshooting
Please contact Spring Water Solutions if any of these issues persist + 6 4 0 9 6 3 6 - 7 0 7 0 | W W W . S P R I N G N Z . C O . N Z | S A L E S @ S P R I N G N Z . C O . N Z... -
Page 11: Push Lock Fitting & Plumbers Delight Installation
PLUMBERS DELIGHT - INSTALLATION Disassemble the existing flexihose from the Cold Water Feed Connect the water feed to the female thread of the Plumbers delight Remove 1'4" tube nut from the top of the Plumbers Delight. Slide the nut over the 1/4" tube. Push the 1/4"... -
Page 12: Leakage Detection And Swivel
LEAKAGE DETECTION - DIAGRAM This device has a leakage detection probe fitted for safety purposes. When the probe detects moisture you may notice the LED on the machine flashing accompianied by a beeping noise We recommend turning off the electricity at the power supply and calling a qualified technician to carry out this work for your safety. -
Page 13: Warranty Info And Maintenance
WARRANTY INFORMATION Spring offers a 24 month back to base warranty on all units from the date of purchase All installation and servicing should be completed by a qualified tradesperson Faults with the product due to incorrect installation or operation may result in voided warranty Details can be filled in via our warranty registration form at springnz.co.nz/warranty-registration-... -
Page 14: Troubleshooting
Trouble Shooting + 6 4 0 9 6 3 6 - 7 0 7 0 | W W W . S P R I N G N Z . C O . N Z | S A L E S @ S P R I N G N Z . C O . N Z... -
Page 15: Product Data Sheet
PRODUCT DATA SHEET Spring NeoTap INSTANT TAP Overview Underbench filter with integrated unit for boiling, chilled, sparkling and ambient drinking water. Model Sparkling, Boiling & Chilled, Boiling, Chilled & Ambient, Sparkling, Chilled & Ambient Filtration Premium KDF/GAC 50, 1 Micron Filtration...
Need help?
Do you have a question about the NEOTAP TOUCH and is the answer not in the manual?
Questions and answers