• To reduce the risk of fire, electrical shock, or motor damage, do not 9 • Troubleshooting ....18 use a solid-state speed control with this fan. Use only Hunter speed controls.
If you want to use an existing fan site, complete the following checklist to System determine if the site is acceptable and safe for your new Hunter fan. If you cannot check off every item, prepare a new fan site as described on this page.
Page 4
ANSI/NFPA 70. If your ceiling fan, go to your fan manual and continue with Section 2 • Installing the you are unfamiliar with wiring, use a Ceiling Plate. qualified electrician. 45055-01 • 02/24/11 • Hunter Fan Company...
Page 5
Support Brace Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angled mounting. The steps in this manual include Ceiling instructions for all three Installer’s Choice mounting methods.
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •...
Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws. Do not over tighten. Flat Washer Steps 2-2 – 2-4 Ceiling Peak Ceiling Peak Large Large Opening Opening 3” Screw LEFT RIGHT Step 2-3 (Angled Ceiling Only) 45055-01 • 02/24/11 • Hunter Fan Company...
3-5. Align the notch on the ball with the indent in the hanger bracket. Indent (Rotate the fan until you hear the notch pop into place.) Steps 3-4 – 3-5 Go to 4 • Wiring the Fan. WARNING: Fan may fall if not assembled as directed in these installation instructions. 45055-01 • 02/24/11 • Hunter Fan Company...
Page 9
WARNING: Fan may fall if not assembled as directed in these installation instructions. Steps 3-8 – 3-9 Low Profile Washer Step 3-7 (Detail) Low Profile Washer Adapter Canopy Trim Ring #8-32 x 3/4” Screw Step 3-10 45055-01 • 02/24/11 • Hunter Fan Company...
4-7. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. 45055-01 • 02/24/11 • Hunter Fan Company...
5-5. Using both hands, push the canopy trim ring up to the top of the Canopy canopy. 5-6. Twist canopy trim ring clockwise to secure the canopy. Should you need to remove the canopy trim ring, follow these steps: 1. Twist canopy trim ring counter clockwise until it releases from canopy. Step 5-3 Step 5-4 Canopy Step 5-5 Screw 45055-01 • 02/24/11 • Hunter Fan Company...
6 • Assembling the Blades Step 6-1 (Detail) Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 6-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades.
7 • Completing Your Installation With or Without a Bowl Light Fixture Your Hunter fan comes with an integrated light fixture assembly and an optional switch housing cap and plug button. This feature gives you the option of installing the fan with OR without the included light fixture.
Page 14
Align the side screw holes in the upper and lower switch Steps 7-6 – 7-7 housings. Attach the lower switch housing to the upper switch Lower Switch Housing housing with three housing assembly screws. Plug Connector Detail Housing Assembly Screw 45055-01 • 02/24/11 • Hunter Fan Company...
Page 15
7-13. Attach the extra pull chains (included) to the light and fan pull chains using the breakaway connector. (You may find the breakaway connector on the end of the extra chain.) For Light Bulbs Metal Disc Metal Rod Glass Bowl Cover Plate Breakaway Finial Connector 45055-01 • 02/24/11 • Hunter Fan Company...
Page 16
7-19. Install the switch housing cap and plug button to the lower switch housing. 7-20. Once you have uninstalled the light fixture, continue with step 7-6. Step 7-16 Male Dummy Terminal Female Dummy Terminal Plug Button Step 7-19 45055-01 • 02/24/11 • Hunter Fan Company...
8-6. The blades on this fan have been treated with Hunter’s Dust Armor protection, making the blades less likely to attract dust and dirt. Use a dry or slightly damp lint free cloth to clean the In cold weather, use upward blades.
If you need parts or service assistance, please call 888-830-1326 (In Canada, call 866-268-1936) or visit us at our Web site at http://www.hunterfan.com. Hunter Fan Company 7130 Goodlett Farms Parkway #400 Memphis, Tennessee 38016 45055-01 • 02/24/11 • Hunter Fan Company...