Quoizel WTO8406WT Assembly Instruction Sheet

Please go to www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (1) A19 Medium Base bulb 100W Maximum or
(1) Medium Base Vintage bulb is recommended but not supplied.
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Fixture can only be mounted in the direction indicated on page 2.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Crossbar Assembly
A
x 1
Alternate
B Mounting screw
x 2
-
STEP 1 Remove Paper Filler
A. Carefully remove paper filler inside of the
Fixture Body (C).
-
STEP 2 Installing the Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
Outlet
Box
Mounting Screw
or Alternate Short
Mounting Screw
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
2017 QuoizelInc.
Assembly Instruction Sheet #IS-WTO8406WT
for product cleaning tips. Go to the
20-30 minutes
Fixture Body
C
x 1
Figure 1
Paper Filler
Outlet Box Screws
(not included)
A
Supply Wires
with Ground Wire
Figure 2
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
For Style WTO8406WT
Care + Maintenance selection.
-
STEP 3 Test Fit the
Backplate to the Crossbar
Assembly
A. Remove the mounting
balls from the Crossbar
Assembly (A). Place the
backplate and Fixture
Body (C) onto the
Crossbar Assembly (A)
and secure with
mounting balls. Note:
The backplate and
Fixture Body (C) should
be snug against the wall
and held tight with the
mounting balls. If it is
not, adjust the length of
C the mounting screw or
alternate short mounting screw on the Crossbar Assembly (A) by
unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws or alternate short mounting screws
in or out of the crossbar until the correct length is achieved. Once
the backplate and Fixture Body (C) is secure, remove the mounting
ball and Fixture Body (C) and proceed to Step 4.
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box
.
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
Bare, or Green
Ground wire
from outlet box
1of2
Mounting Screw
or Alternate Short
Mounting Screw
A
Hex Nut and
Lock Washer
Backplate
Figure 3
White wire
from fixture
Black wire
from fixture
Ground wire
from fixture
OR
Ground wire
from fixture
Green Ground Screw
on the Crossbar
ReleasedDate:2017-03-07
Mounting
Ball
C
Figure 4