1.1 Symbols and signal words In this section you will find an overview of the meaning of symbols and signal words that are used in this document. Reflect 5, Reflect 6, Reflect 8 Passive Speaker...
Page 6
This combination of symbol and signal word indicates a pos‐ sible dangerous situation that can result in material and environmental damage if it is not avoided. Warning signs Type of danger Warning – suspended load. Warning – danger zone. Reflect 5, Reflect 6, Reflect 8 Passive Speaker...
Decrease the volume level immediately if you experience ringing in your ears or hearing impairment. If this is not possible, keep a greater distance or use adequate ear-muffs. Reflect 5, Reflect 6, Reflect 8 Passive Speaker...
Page 8
In environments with increased dirt levels (for example due to dust, smoke, nicotine or mist): Have the device cleaned by qualified specialists at regular intervals to prevent damage due to overheating and other malfunctions. Reflect 5, Reflect 6, Reflect 8 Passive Speaker...
When installing and operating, make sure to follow the standards and regulations that apply in your country. In Germany, this is DGUV regulation 17 “Staging and Production Facilities for the Entertainment Industry”. Ensure that speakers are only mounted by trained specialists. Reflect 5, Reflect 6, Reflect 8 Passive Speaker...
Page 12
If the device is connected to an amplifier that is switched on, the amplifier may be damaged. Ensure that the amplifier to which you want to connect the device is switched off before you connect the device. Reflect 5, Reflect 6, Reflect 8 Passive Speaker...
4.1 Installation Wall mounting The following illustration shows how the supplied mounting bracket can be attached to the wall. Check the condition of the substrate and use suitable fastening material (not included). Reflect 5, Reflect 6, Reflect 8 Passive Speaker...
Page 15
The selection of the power tap defines the maximum output level of a speaker. This means that different sound zones can be implemented by setting different power taps on one ampli‐ fier channel. Note that this is not possible with low-impedance operation (8 Ω). Reflect 5, Reflect 6, Reflect 8 Passive Speaker...
For low-impedance use, pay attention to high-quality cables with sufficient cable cross-section. Note that the combination of a 100 V system and a low-impedance system on an amplifier channel is not possible. Reflect 5, Reflect 6, Reflect 8 Passive Speaker...
Page 17
If you notice distortion during operation, either the amplifier or the speaker is overloaded. This may permanently damage the amplifier or the speaker. Always reduce the volume as soon as you notice any distortion. Reflect 5, Reflect 6, Reflect 8 Passive Speaker...
Technical specifications Technical specifications 5.1 Reflect 5 (item no. 508920, 508921) 254 mm System Passive 2-way speaker Configuration Woofer 1 × 5.25” speaker (ferrite) with 1” voice coil Tweeter 1 × 1” silk dome (neodymium) with 1” voice coil 258 mm...
Page 19
Black (item no. 508920), white (item no. 508921) Dimensions (W × H × D), 258 mm × 163 mm × 188 mm with mounting bracket Weight 2.75 kg Ambient conditions Temperature range 0 °C…40 °C Relative humidity 20%…80% (non-condensing) Reflect 5, Reflect 6, Reflect 8 Passive Speaker...
Page 20
Technical specifications Frequency response The following figure shows the course of the sound pressure level at 1 W/1 m (1) and of the impedance (2) depending on the signal frequency. Ω ö Reflect 5, Reflect 6, Reflect 8 Passive Speaker...
140 mm Rated impedance 8 Ω 178,5 mm Max. sound pressure level 105 dB SPL Max. short-term sound pres‐ 90.3 dB SPL sure level Beam angle (H × V) 120° × 100° Reflect 5, Reflect 6, Reflect 8 Passive Speaker...
Page 23
Black (item no. 508922), white (item no. 508923) Dimensions (W × H × D), 285 mm × 195 mm × 227 mm with mounting bracket Weight 3.45 kg Ambient conditions Temperature range 0 °C…40 °C Relative humidity 20%…80% (non-condensing) Reflect 5, Reflect 6, Reflect 8 Passive Speaker...
Page 24
Technical specifications Frequency response The following figure shows the course of the sound pressure level at 1 W/1 m (1) and of the impedance (2) depending on the signal frequency. Ω ö Reflect 5, Reflect 6, Reflect 8 Passive Speaker...
240 mm Rated impedance 8 Ω 278 mm Max. sound pressure level 106 dB SPL Max. short-term sound pres‐ 90.3 dB SPL sure level Beam angle (H × V) 120° × 100° Reflect 5, Reflect 6, Reflect 8 Passive Speaker...
Page 27
Black (item no. 508924), white (item no. 508925) Dimensions (W × H × D), 381 mm × 250 mm × 285 mm with mounting bracket Weight 5 kg Ambient conditions Temperature range 0 °C…40 °C Relative humidity 20%…80% (non-condensing) Reflect 5, Reflect 6, Reflect 8 Passive Speaker...
Page 28
Technical specifications Frequency response The following figure shows the course of the sound pressure level at 1 W/1 m (1) and of the impedance (2) depending on the signal frequency. Ω ö Reflect 5, Reflect 6, Reflect 8 Passive Speaker...
Do not dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the instructions and markings on the packaging. Observe the disposal note regarding documentation in France. Reflect 5, Reflect 6, Reflect 8 Passive Speaker...
Page 32
Repairing a device or passing it on to another user is an ecologically valuable alternative to disposal. For example, use the classified ads of Thomann GmbH. If your old device contains personal data, delete those data before disposing of it. Reflect 5, Reflect 6, Reflect 8 Passive Speaker...
Need help?
Do you have a question about the Reflect 5 and is the answer not in the manual?
Questions and answers