Page 1
UPA-612W HYBRID PORTABLE PA SYSTEM User’s Manual...
Page 2
Safety Related Symbols 'sinstructions.To avoid the risk of electric shock and damage, do notsubject this product to any liquid/rain or moisture.Do not use this product when in close proximity to water.Do not install this product near any direct heat source.Do not block areas of ventilation. This symbol, wherever used, alerts you to the Failure to do so could result in fire.Keep product away presence of uninsulated and dangerous voltages within...
1. Introduction Thank you for purchasing the UPA-612W 2-way vented powered speaker system. This unique system was designed to be an all- in one portable solution with built-in High Power amplifier, 4 channels mixer with 3-band EQ and 24-bit DSP effects. The UPA- 612W combines practicality with top design concepts achieved over many years of manufacturing quality products.
Page 5
QUALIZER The UPA-612W features a 3-band equalizer which allows you to adjust the high, mid and low frequencies separately on each mono channel. 5. HIGH This is the treble control. You can use it to get rid of high frequency noises or to boost the sound of cymbals or the high harmonics of the human voice.
Page 6
The EQ function will be activated automatically as soon as you operate your UPA-612W . 15. MAIN MIX LEVEL Control This control is used to adjust the overall volume of the main mix output. The adjustable range goes from - to +10dB.
Page 7
This switch is used to turn the unit on/off. 39. AC INPUT Standard IEC receptacle, connect your UPA-612W to the main electrical outlet with the supplied power cord. 40. VOLTAGE SELECTOR There are two kinds of voltages for your operation from this switch, you can select the voltage at 115V or 230V.
Page 8
48. PHONE Jack & SPEAKON Connector These jacks are used to connect UPA-612W-615 passive speakers. They are configured with a speakon connector and 1/4” phone jack. You can determine the signal that is outputted to these jacks. NOTE: In order to avoid damaging your built-in amplifier, please pay more attention to the impedance of speaker. Lower load impedances are not permitted.
Page 9
no signal being received. 51. MIC. ON & Diversity Signal Indicator These indicators light up during standby. When microphone signal is received, the A or B signal indicator lights up to indicate the reception of microphone. 52. POWER ON Indicator When the unit powered on, this blue LED will lights up.
3) Complete other connections as illustrated. And then turn the power on. 4) Turn up the volume controls of the UPA-612W to about 70%. 5) Use the mixer PFL function of the UPA-612W to get the proper input level, and adjust the Main Mix Level control to manipulate the output level.
6.1 Set-up Ok, you have reached this point and you are now in the position to successfully operate your UPA-612W. However, we advise you to read carefully the following section to be the real master of your unit. Not paying enough attention to the input signal level, to the routing of the signal and the assignment of the signal will result in unwanted distortion, a corrupted signal or no sound at all.
Page 12
For1/4"PhoneJack ForXLRConnector -In line Connection For these applications, the UPA-612W provides 1/4" TRS connectors, XLR connectors and RCA connectors to interface with most professional audio devices easily. Follow the configuration examples below for your particular connection. Balanced Unbalanced -In line Connection If you are connecting to a mixing console's main inserts, you may have single TRS jack for Send &...
9. TECHNICAL SPECIFICATIONS SPECIFICATIONS UPA-612W bal Mic/Line channels in Tape in 1 RCA in+1 Mini ST in Fx RTN in Main out Monitor out Fx send REC out MIC TO MAIN/MON 50dB GAIN LINE TO MAIN/MON 30dB FREQUENCY RESPONSE(-1dB) 20Hz-20KHz...
SIRUS PRO, will repair this unit in counted a term nongreater to 30 days as of the date of entrance of the unit to the Technical Service. In those cases in that due to the particularitity of the spare part, outside necessary their import, the repair time and the viability of the same one will be subject to the effective norms for the import of parts, in which case one will inquire to the user about the term and possibility into repair.
Need help?
Do you have a question about the UPA-612W and is the answer not in the manual?
Questions and answers