OST RuggedNet GLPoE/Si Manual

Unmanaged industrial single pair power over ethernet switch

Advertisement

RuggedNet
Unmanaged Industrial
Single Pair Power over Ethernet Switch
User Manual
38 Tesla, Irvine, CA 92618 USA
Phone: (949) 250-6510; Fax: (949) 250-6514
GLPoE/Si
®
General and Copyright Notice
This publication is protected by U.S. and international copyright laws. All rights
reserved. The whole or any part of this publication may not be reproduced, stored
in a retrieval system, translated, transcribed, or transmitted, in any form, or by
any means, manual, electric, electronic, electromagnetic, mechanical, chemical,
optical or otherwise, without prior explicit written permission of Omnitron Systems
Technology, Inc.
The following trademarks are owned by Omnitron Systems Technology, Inc.:
FlexPoint
, FlexSwitch
, iConverter
®
TM
OmniConverter
, RuggedNet
, Omnitron
®
®
OST
and the Omnitron logo.
TM
All other company or product names may be trademarks of their respective owners.
The information contained in this publication is subject to change without notice.
Omnitron Systems Technology, Inc. is not responsible for any inadvertent errors.
Warranty
This product is warranted to the original purchaser (Buyer) against defects in
material and workmanship for a period of two (2) years from the date of shipment.
A five (5) year warranty may be obtained by the original purchaser by registering
this product at www.omnitron-systems.com/support within ninety (90) days from the
date of shipment. During the warranty period, Omnitron will, at its option, repair or
replace a product which is proven to be defective with the same product or with a
product with at least the same functionality.
For warranty service, the product must be sent to an Omnitron designated facility,
at Buyer's expense. Omnitron will pay the shipping charge to return the product
to Buyer's designated US address using Omnitron's standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to product malfunctions resulting from
improper or inadequate use and/or maintenance of the equipment by Buyer, Buyer-
supplied equipment, Buyer-supplied interfacing, unauthorized modifications or
tampering with equipment (including removal of equipment cover by personnel not
specifically authorized and certified by Omnitron), or misuse, or operating outside
the environmental specification of the product (including but not limited to voltage,
ambient temperature, radiation, unusual dust, etc.), or improper site preparation
or maintenance.
No other warranty is expressed or implied. Omnitron specifically disclaims the implied
warranties of merchantability and fitness for any particular purpose.
The remedies provided herein are the Buyer's sole and exclusive remedies. Omnitron
shall not be liable for any direct, indirect, special, incidental, or consequential
damages, whether based on contract, tort, or any legal theory.
, miConverter
, NetOutlook
, OmniLight
®
®
®
, Omnitron Systems Technology, Inc.
®
Page 2
,
®
,
TM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RuggedNet GLPoE/Si and is the answer not in the manual?

Questions and answers

Summary of Contents for OST RuggedNet GLPoE/Si

  • Page 1 General and Copyright Notice This publication is protected by U.S. and international copyright laws. All rights reserved. The whole or any part of this publication may not be reproduced, stored in a retrieval system, translated, transcribed, or transmitted, in any form, or by any means, manual, electric, electronic, electromagnetic, mechanical, chemical, optical or otherwise, without prior explicit written permission of Omnitron Systems Technology, Inc.
  • Page 2: Product Overview

    Product Overview Directive) of the European Community directive 2012/19/EU on waste electrical and The RuggedNet GLPoE/Si is an unmanaged Industrial Single Pair Power over electronic equipment (WEEE) which, together with the RoHS Directive 2015/863/ EU, for electrical and electronic equipment sold in the EU after July 2019. Such Ethernet (SPoE) switch that is IEEE 802.3cg compliant and features copper or fiber...
  • Page 3: Installation Procedure

    F2 is only forwarded to the uplink port F1, preventing the broadcast traffic from flooding other network ports. Incoming traffic from uplink port F1 is flooded to all DIP-switches are located on the top of the RuggedNet GLPoE/Si. The DIP-switches user ports and uplink port F2.
  • Page 4 Dual Device Mode Redundant Uplink When configured for Dual Device Mode and Directed Switch Mode, the traffic from When configured for Uplink Redundant Mode “return to primary”, a fault on the ports P1 and P2 is only forwarded to uplink port F1 and ports P3 and P4 are only primary Port F1, will cause a fail over to the secondary Port F2 within 50msec.
  • Page 5: Installing The Module

    Pause Pause frames will be configured to advertise Symmetrical and Asymmetrical Pause capability on all ports. L2CP All Layer 2 Control Protocol (L2CP) frames will be tunneled. Top View - Location of DC Power and DIP-switches 2) Installing the Module The module can be wall or rack mounted using the optional Wall Mount Plate (8260-3).
  • Page 6: Connect Cables

    4) Connect Cables If the switch supports SFP transceivers,insert the SFP fiber transceiver into the SFP receptacle on the front of the switch (see the SFP Data Sheet 091-17000-001 for supported Gigabit or Fast Ethernet transceivers). NOTE: The release latch of the SFP fiber transceiver must be in the closed (up) position before insertion.
  • Page 7: Specifications

    RuggedNet GLPoE/Si Uplink Ports LED Indicators - SFP and Copper Uplink Models ® Description 10T/T1L to 100/1000 Fiber or 10/100/1000 Copper Uplinks Legend Indicator Description Unmanaged Industrial SPoE Ethernet Switch No link Standard Compliances IEEE 802.3, 802.3cg Green - ON Port linked at 100Mbps FDx Environmental REACH, RoHS and WEEE...
  • Page 8 Mechanical Customer Support Information If you encounter problems while installing this product, contact Omnitron Technical Support: Phone: (949) 250-6510 Fax: (949) 250-6514 Address: Omnitron Systems Technology, Inc. 38 Tesla Irvine, CA 92618, USA Email: support@omnitron-systems.com URL: www.omnitron-systems.com 040-02935-001A 4/25 Page 15 Page 16...

Table of Contents