1. Manuals
  2. Brands
  3. Murata Manuals
  4. Industrial Electrical
  5. GCJ31MR71E104KA01 Series
  6. Reference sheet

Murata GCJ31MR71E104KA01 Series Reference Sheet

Only reflow soldering chip monolithic ceramic capacitor soft termination type for automotive
Hide thumbs

Advertisement

Table of Contents

Only Reflow Soldering
CHIP MONOLITHIC CERAMIC CAPACITOR SOFT TERMINATION TYPE FOR AUTOMOTIVE
GCJ31MR71E104KA01_ (1206, X7R, 0.1uF, 25Vdc)
_: packaging code
1.Scope
This product specification is applied to Chip Monolithic Ceramic Capacitor Soft Termination Type used for Automotive
Electronic equipment.
This product is applied for Only Reflow Soldering.
　　
2.MURATA Part NO. System
(Ex.)
GCJ
31
(1)L/W
Dimensions
3. Type & Dimensions
L
W
T
e
g
e
(1)-1 L
(1)-2 W
3.2±0.3
1.6±0.3
4.Rated value
(3) Temperature Characteristics
(Public STD Code):X7R(EIA)
Temp. coeff
or　Cap. Change
-15 to 15 %
5.Package
mark
(8) Packaging
f180mm Reel
L
EMBOSSED W8P4
f330mm Reel
K
EMBOSSED W8P4
Product specifications in this catalog are as of Feb.1,2013,and are subject to change or obsolescence without notice.
Please consult the approval sheet before ordering.
Please read rating and !Cautions first.
GCJ31MR71E104KA01-01
M
R7
(2)T
(3)Temperature
Dimensions
Characteristics
(2) T
1.15±0.2
0.3 to 1.0
(4)
DC Rated
Temp. Range
Voltage
(Ref.Temp.)
-55 to 125 °C
25 Vdc
(25 °C)
Packaging Unit
3000 pcs./Reel
10000 pcs./Reel
1E
104
(6)Capacitance
(4)DC Rated
(5)Nominal
Tolerance
Voltage
Capacitance
(Unit:mm)
e
g
1.5 min.
(6)
(5) Nominal
Capacitance
Capacitance
Tolerance
0.1 uF
±10 %
1
Reference Sheet
K
A01
(7)Murata's
(8)Packaging
Control Code
Specifications and Test
Methods
(Operating
Temp. Range)
-55 to 125 °C
L
Code

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GCJ31MR71E104KA01 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Murata GCJ31MR71E104KA01 Series

Summary of Contents for Murata GCJ31MR71E104KA01 Series

  • Page 1 Reference Sheet 1.Scope This product specification is applied to Chip Monolithic Ceramic Capacitor Soft Termination Type used for Automotive Electronic equipment. This product is applied for Only Reflow Soldering. 　　 2.MURATA Part NO. System (Ex.) (7)Murata’s (2)T (6)Capacitance (8)Packaging (1)L/W...
  • Page 2 ■AEC-Q200 Murata Standard Specification and Test Methods AEC-Q200 Test Item Specification. AEC-Q200 Test Method 1 Pre-and Post-Stress Electrical Test 2 High Temperature The measured and observed characteristics should satisfy the Set the capacitor for 1000±12 hours at 150±3℃. Set for Exposure (Storage) specifications in the following table.
  • Page 3 ■AEC-Q200 Murata Standard Specification and Test Methods AEC-Q200 Test Item Specification. AEC-Q200 Test Method The measured and observed characteristics should Operational Life Apply 200%* of the rated voltage for 1000±12 hours at 125±3℃. satisfy the specifications in the following table.
  • Page 4 ■AEC-Q200 Murata Standard Specification and Test Methods AEC-Q200 Test Item Specification. AEC-Q200 Test Method 14 Thermal Shock The measured and observed characteristics should satisfy Fix the capacitor to the supporting jig in the same manner and under the specifications in the following table.
  • Page 5 ■AEC-Q200 Murata Standard Specification and Test Methods AEC-Q200 Test Item Specification. AEC-Q200 Test Method Appearance No marking defects Board Flex Solder the capacitor on the test jig (glass epoxy board) shown in Fig1 using a eutectic solder. Then apply a force in the direction shown in Fig 2 for 5±1sec.
  • Page 6 ■AEC-Q200 Murata Standard Specification and Test Methods AEC-Q200 Test Item Specification. AEC-Q200 Test Method No bias R1,R7 : Within ±15% Capacitance The capacitance change should be measured after 5 min. at (-55℃ to +125℃) each specified temperature stage. Temperature : Within ±22% Characteristics (-55℃...
  • Page 7 Ｐａｃｋａｇe ＧＣＪ　Ｔｙｐｅ 1.Tape Carrier Packaging(Packaging Code:D/E/F/L/J/K) 1.1 Minimum Quantity(pcs./reel) φ180mm reel φ330mm reel Type Paper Tape Plastic Tape Paper Tape Plastic Tape Code:D/E Code:L Code:F/J Code:K GCJ18 4000 10000 4000 10000 GCJ21 4000 10000 3000 10000 3000 10000 GCJ31 3000 10000 2000 6000...
  • Page 8 Ｐａｃｋａｇe ＧＣＪ　Ｔｙｐｅ 　(2)GCJ21/31/32 T:0.85 min. (in:mm) 0.25±0.1(T≦1.80mm) 4.0±0.1 4.0±0.1 0.3±0.1(T：2.5mm) 2.0±0.1 +0.1 φ1.5 Ａ ＊4 1.7 max.(T≦1.25mm) 2.5 max. (T:1.35/1.6mm) 3.0 max. (T:1.8/2.0mm) 3.7 max. (T≧2.5mm) ＊4 Code GCJ21 GCJ31 GCJ32 1.45±0.2 1.9±0.2 2.8±0.2 2.25±0.2 3.5±0.2 3.5±0.2 JEMCGP-01896...
  • Page 9 め状態 ( 単位： mm) Ｐａｃｋａｇe ＧＣＪ　Ｔｙｐｅ (in:mm) Fig.1 Package Chips Chip Fig.2 Dimensions of Reel 2.0±0.5 φ21±0.8 ｗ Fig.3 Taping Diagram GCJ32 max. 16.5 max. 10±1.5 Top Tape : Thickness 0.06 Feeding Hole :As specified in 2.2. Hole for Chip : As specified in 2.2. Bottom Tape :Thickness 0.05 (Only a bottom tape existence ) Base Tape : As specified in 2.2.
  • Page 10 Ｐａｃｋａｇe ＧＣＪ　Ｔｙｐｅ ﾁｯﾌﾟ詰め状態 ( 単位： mm) 1.3 Tapes for capacitors are wound clockwise shown in Fig.3. (The sprocket holes are to the right as the tape is pulled toward the user.) 1.4 Part of the leader and part of the vacant section are attached as follows. (in:mm) Tail vacant Section Chip-mounting Unit...

  • Page 11: Limitation Of Use

    Caution ■ Limitation of use Please contact our sales representatives or product engineers before using our products for the applications listed below which require of our products for other applications than specified in this product. 　　　①Aircraft equipment ②Aerospace equipment ③Undersea equipment ④Power plant control equipment 　　　⑤Medical equipment ⑥Transportation equipment(vehicles,trains,ships,etc.) ⑦Traffic signal equipment 　　　⑧Disaster prevention / crime prevention equipment...
  • Page 12 Caution ■Rating 1.Temperature Dependent Characteristics 1. The electrical characteristics of the capacitor can change with temperature. 1-1. For capacitors having larger temperature dependency, the capacitance may change with temperature changes. The following actions are recommended in order to insure suitable capacitance values. (1) Select a suitable capacitance for the operating temperature range.
  • Page 13 Caution 3.Applied Voltage 1. Do not apply a voltage to the capacitor that exceeds the rated voltage as called-out in the specifications. 1-1. Applied voltage between the terminals of a capacitor shall be less than or equal to the rated voltage. (1) When AC voltage is superimposed on DC voltage, the zero-to-peak voltage shall not exceed the rated DC voltage.
  • Page 14 Caution 5. DC Voltage and AC Voltage Characteristic 1. The capacitance value of a high dielectric constant type capacitor changes depending on the DC voltage applied. Please consider the DC voltage characteristics when a capacitor is selected for use in a DC circuit. 1-1.

  • Page 15: Vibration And Shock

    Caution 7.Vibration and Shock 1. The capacitors mechanical actress (vibration and shock) shall be specified for the use environment. Please confirm the kind of vibration and/or shock, its condition, and any generation of resonance. Please mount the capacitor so as not to generate resonance, and do not allow any impact on the terminals.
  • Page 16 Caution 2.Information before mounting 1. Do Not re-use capacitors that were removed from the equipment. 2. Confirm capacitance characteristics under actual applied voltage. 3. Confirm the mechanical stress under actual process and equipment use. 4. Confirm the rated capacitance, rated voltage and other electrical characteristics before assembly. 5.
  • Page 17 Caution 4-1.Reflow Soldering 1. When sudden heat is applied to the components, the [Standard Conditions for Reflow Soldering] mechanical strength of the components will decrease because a sudden temperature change causes Infrared Reflow deformation inside the components. In order to prevent Temperature(℃) mechanical damage to the components, preheating is Soldering...
  • Page 18 Caution 4-2.Leaded Component Insertion 1. If the PCB is flexed when leaded components (such as transformers and ICs) are being mounted, chips may crack and solder joints may break. Before mounting leaded components, support the PCB using backup pins or special jigs to prevent warping. 5.Washing Excessive ultrasonic oscillation during cleaning can cause the PCBs to resonate, resulting in cracked chips or broken solder joints.
  • Page 19 Caution 7.Printed Circuit Board Cropping 1. After mounting a capacitor on a printed circuit board, do not apply any stress to the capacitor that is caused by bending or twisting the board. 1-1. In cropping the board, the stress as shown right may cause the capacitor to crack. Try not to apply this type of stress to a capacitor.
  • Page 20 Caution ■ Others 1. Under Operation of Equipment 1-1. Do not touch a capacitor directly with bare hands during operation in order to avoid the danger of a electric shock. 1-2. Do not allow the terminals of a capacitor to come in contact with any conductive objects (short-circuit). Do not expose a capacitor to a conductive liquid, inducing any acid or alkali solutions.
  • Page 21 Notice ■ Rating 1.Operating Temperature 1. The operating temperature limit depends on the capacitor. 1-1.Do not apply temperatures exceeding the upper operating temperature. It is necessary to select a capacitor with a suitable rated temperature which will cover the operating temperature range.

  • Page 22: Pcb Design

    Notice ■ Soldering and Mounting 1.PCB Design 1. Notice for Pattern Forms 1-1. Unlike leaded components, chip components are susceptible to flexing stresses since they are mounted directly on the substrate. They are also more sensitive to mechanical and thermal stresses than leaded components. Excess solder fillet height can multiply these stresses and cause chip cracking.
  • Page 23 Notice 2. Land Dimensions Chip Capacitor Land 2-1. Chip capacitor can be cracked due to the stress of PCB bending / etc if the land area is larger than needed and has an excess amount of solder. Solder Resist Please confirm the suitable land dimension by evaluating of the actual SET / PCB. Table 1 Reflow Soldering Method Dimensions Chip（L×W）...
  • Page 24 Notice 2.Washing 1. Please evaluate a capacitor by actual cleaning equipment and condition surely for confirming the quality and select the applicable solvent. 2. Unsuitable cleaning solvent may leave residual flux, other foreign substances, causing deterioration of electrical characteristics and the reliability of the capacitors. 3.
  • Page 25 NOTE 1.Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. 2.Your are requested not to use our product deviating from this product specification. 3.We consider it not appropriate to include any terms and conditions with regard to the business transaction in the product specifications, drawings or other technical documents.
  • Page 26 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Murata GCJ31MR71E104KA01K GCJ31MR71E104KA01L...

This manual is also suitable for:

Gcj31mr71e104ka01l

Table of Contents