Page 1
Principle and Maintenance of ABS535T CONTENTS Chapter I Overview of ABS535T 1、Description of Functions 2、Block Diagram of Player 3、Composition of IC for Player Chapter II Operating Principle of Servo Circuit 1、Processing Procedure of Digital Signal 2、Processing Procedure of Control Signal Chapter III Operating Principle of Decoding Circuit 1、Control Circuit of System...
Page 2
Important prompt: This type player employs two kinds of decks, SF-HD62 and SF-HD60, and corresponding software of these two types of decks are different, therefore please pay special attention during deck changing in the maintenance. Corresponding decks should be changed with the same type of original ones, otherwise the player will be out of order.
Operating Principle Analysis of ABS535T Chapter I Overview of ABS535T ABS535T is a medium- low-grade model integrating with video disc and power amplifier, with the following major features: 1. The layer adopts “ Sanyo loader+MT1389” solution; 2. The power amplifier adopts the digital power amplification circuit, with the power IC of TAS5112DFD;...
Page 4
II. Block Diagram of ABS535T Complete Player and IC Function Table Radio reception head composite 29LV160BE S terminal AT24C02 16M ROM Y/Cb/Cr status MT1389 Sany 4340,7265 deck 6-way Audio D/A, power BA5954 focus HCU04 track Refor fiber, feed main Y/Pb/Pr...
Chapter II Operating Principle of Servo Circuit I. Digital Signal Processing Procedure ABS535T adopts Sanyo double beam super error correction deck and MTK decoding solution, and its servo circuit mainly consists of preposition signal processing, digital servo processing, digital signal processing IC MT1389 and driver circuit BA5954. MT1389 is also a main part of the decoding circuit.
Page 6
through the 2-13 pins of MT1389, and after amplifying treatment of built- in amplifier of MT 1389, the signals are treated in two parts within MT1389: After being processed by the internal digital servo signal circuit of MT1389, part of the signal forms into corresponding servo control signal, and output focus (FOSO), tracking (TRSO), main shaft (DMSO) and feed (FMSO) servo control signal from the P42, P41, P37 and P38 of MT1389 and send them to the driver circuit BA5954 to amplify the drive.
Page 7
Figure III Different from the circuit in former MTK solution, the MT1389 is integrated with preposition signal processing circuit, so the tray open/close control signals are accomplished by MT1389, that is to say, the close control signal is accomplished by the Pin 51 of MT1389, while the open control signal by Pin 39 of MT1389.
Page 8
Figure IV During playing, if we press the OPEN button, the main shaft drive signal will disappear, and because of inertia, the main shaft motor is still in operation. As the electromotive force generated in the operation of motor receives the induction voltage on sampling resistors R321 and R340, which, through the resistor R319 and R320, is added to the Pin 36 and Pin 35 of MT1389, and outputted from the Pin 34 after internal processing for amplification in MT1389, and delivered to Pin 47 of MT1389 through R318.
The STBY on Pin 28 of BA5954 is an output-enabling signal, and only when the pin is in high power level, there will be output of drive voltage on the output terminal. Chapter III Operating Principle of Decoding Circuit The decoding circuit of the player mainly consists of decoding chips (including MT1389, SDRAM AE45164016 and FLASH ROM 29LV160BE) and audio DAC CS4360.
Page 10
II. Audio and Video Output Circuit 1. Video output circuit ABS535T can not only output three types of alternating- line video signal (including CVBS composite video, S terminal Y -C signal and Y/Cb/Cr color difference signal), but also output two types of progressive line video signal (including Y/Pb/Pr progressive line color difference signal and VGA progressive line signal).
Page 11
ABS535T has the function of radio reception, and can also receive RDS signal. The radio head control lines CE, DI, CL and DO are controlled by 28 array lines connecting to MT1389 control.
When any of the controlling lines is in abnormality, the radio reception will be in malfunction. The RDS signal received by radio head will be delivered to the dedicated IC SAA6588 for processing. Chapter IV Operating Principle of Power Board I.
Page 13
group supplying power for 3.3V is lower, it adopts 17431. For two ICs are different, you should pay special attention to distinguish them from each other. They cannot be used mixing. Chapter 5: Panel control and VFD display circuit The panel mainly consists of VFD screen, driver ICD16311, remote receptor HS0038A2 and button and indicator display circuit, mainly for accomplishing man-player dialogue and display of operation status.
When in normal condition, this detection pin is of high level around 3.3V. Troubleshooting I. Voltage on key points of ABS535T Demoding circuit: Reset: 1. U205 (HC U04): 8 pins, around 5V;...
Page 15
II. Troubleshooting of main troubles No picture, no sound, no VFD display Check the voltage of power board, Check if power supply of MT1389 and check if the decoding board is 3.3V, 1.8V is right? short circuit to the grounding. Check if clock oscillating circuit If the clock signal output XO 27M crystal oscillator, C275,...
Page 16
Do not read disc Check if the connection from Check if the feed control BA5954 to MT1389 laser Check input of BA5954 Pin 23 is is open circuit? head has feed action. 1.4V? Check if BA5954 pin 17,18 Check feed motor have 2.5V voltage output? and its connection.
Page 17
Check if there is Check if the signal Check MT1389 and its laser coming out voltage of LD01, LD02 connection. from laser head? is 3.2V? Check if V301 and V302 Check if the laser head electron collector voltage is and its array line are 2.3V? right? Check if the control...
Page 18
Attachment :Brief Introduction to IC Pins I. MT1389 MT1389 adopts the LQFP 256 pin packaging and 3.3V/1.8V double voltage operation mode. It is a piece of large-scale CD-ROM and DVD-ROM preposition processing CMOS integrated circuit with excellent performance, and a single chip dedicated to CD/VCD/DVD player. It contains focusing servo error amplification, tracking servo error amplification and RF level output servo control, including the following main functions: RF small signal preposition processing, mainly for carrying our corresponding processing and...
Page 19
DVD-RAM main light beam RF DC signal input B DVD-RAM main light beam RF DC signal input C DVD-RAM main light beam RF DC signal input D DVD-RAM auxiliary light beam RF DC signal input A DVD-RAM auxiliary light beam RF DC signal input B DVD-RAM auxiliary light beam RF DC signal input C...
Page 20
TEZISLV Tracking zero crossover error input OP_OUT Sensing signal amplification output OP_INN Sensing signal phase inversion input OP_INP Sensing signal non- inverting input Main shaft control signal output Feed control signal output TROPEN PWM Tray Open signal output First-route pulse width demodulating PWMOUT1/ADIN9 signal output/AD universal input Tracking control signal output...
Page 21
capacitor APLLVSS Analogue phase lock loop grounding APLLVDD3 Analogue phase lock 3.3V power supply IOWR FLASH read control signal 67-72 HIGHA3-7 Micro-controller address bit 3-7 73、80、108、 127、141、155、 DVDD3 Digital 3.3V power supply 167、182、204、 74、75 HIGHA1-2 Micro-controller address bit 1-2 IOA20 Micro-controller address bit 20 IOCS FLASH chip selection...
Page 22
INT0 Micro-processor interruption 0 DQM0 DRAM input output shielding signal DQS0 DRAM input output shielding signal DRAM data 117-118 RD5-6 DRAM data 120-121 RD3-4 DRAM data 123-125 RD0-2 DRAM data RD15 DRAM data 128-133 RD9-14 DRAM data DRAM data DQS1 DRAM input output shielding signal DQM1 DRAM input output shielding signal...
Page 23
RD26 DRAM data 176-177 RD24-25 DRAM data 178-179 DQM2-3 DRAM I/O shielding signal 180-181 RD22-23 DRAM data 183-188 RD16-21 DRAM data DACVDDC D/A conversion 3.3V power supply VREF Reference voltage YUV0/CIN DACVSSC D/A conversion grounding Video signal YUV1 output/Y signal YUV1/Y output DACVDDB...
Page 24
SPLRCK SPBCK/ASDATA5 ALRCK Audio left and right sound channel clock ABCK Audio bit clock ACLK Audio DAC external clock 217-220 ASDATA0-3 Audio series data ASDATA4 Audio series data MC_DATA Microphone digital audio input SPDIF Digital audio signal output RFGND18 RF signal grounding RFVDD18...
Page 25
crossover checking CRTPLP RFGND RF grounding CEQP CEQN RFGC IREF Reference current AVDD3 Analogue 3.3V power supply Ⅱ.BA5954 BA5954 is a piece of servo drive single-piece integrated circuit, with built- in 4-channel BTL drive circuit.
Page 26
VOSL- Main shaft drive inverse voltage output VO2+ Main shaft forward voltage output VOFC- Focusing drive inverse voltage output VOSC+ Focusing drive forward voltage output VOTK+ Tracking drive forward voltage output VOTK- Tracking drive inverse voltage output VOLD+ Feed drive forward voltage output VOLD- Feed drive inverse voltage output PGND...
Page 27
High Reset × × × × High resistance High resistance resistance The functions of pins of 29LV160BE are as the following table: Name Function RY/BY Ready/system is busy 1~9、16~25 、48 20-byte address bus A0~A19 Chip enabling 27、46 Grounding Output enabling 29~36、38~44 DQ0~DQ14 15-byte data bus...
Page 28
LDQM Data I/O shielding signal Write control signal Column address gate signal Row address gate signal Chip selection signal Section address 0 gate signal SD-BS0 SD-BS1 Section address 1 gate signal 22~26、29~35 MA[0~11] 12-byte address bus 36、40 Neutral pin Clock enabling signal System clock input UDQM Data I/O shielding signal...
Page 29
RESERVED Connect to digital grounding Digital signal Clock signal LRCLK RF channel clock signal SCLK Audio clock signal SDIN4 Audio data input pin SDIN3 Audio data input pin SDIN2 Audio data input pin SDIN1 Audio data input pin PSVC Control PWM signal output VR_DIG 1.8V reference voltage of digital core DVSS...
Page 30
IV. IC TAS5112 IC TAS5112 is an audio power amplifier of high performance made by TI. Bridging with 6O loading, each channel can output 50W. It has 95DB dynamic range, low distortion degree and low rate of heat generation with power efficiency up to 90%. It also has functions of low-voltage protection, high-temperature protection, overflow protection, etc.
Page 31
RESET_AB Reset signal , valid in low level RESET_CD Reset signal , valid in low level SD_AB Signal switch off control SD_CD Signal switch off control IIV. IC SE5532 IC SE5532 is an amplified IC with dual channels and low noise. Compared to most other amplified ICs, it has lower noise, better output performance and power bandwidth.
Page 48
MATERIAL MATERIAL NAME SPECIFICATIONS LOCATION CODE 0881157 HY57V641620HGT-H TSOP U211 0881661 IC42S16400-7T TSOP U211 0881969 IP1117-ADJ SOT-223 U209 0881182 IC LM1117MP-ADJ SOT-223 U209 0881031 IC 24C02N SOP U202 0881990 MT1389FE/B(B)QFP U201 0881897 IC MT1389EE QFP U201 0881459 D5954 SOP U302 0881378 IC BA5954FP HSOP U302...
Page 49
MATERIAL MATERIAL NAME SPECIFICATIONS LOCATION CODE 0010063 METAL FILM RESISTOR 1/4W4.7K±1% SHAPED 10 R513 0010101 METAL FILM RESISTOR 1/4W12K±1% SHAPED 10 R514 0010273 METAL FILM RESISTOR 1/4W24K±1% SHAPED 10 R524 0010306 METAL OXIDE FILM RESISTOR @1W680K±5% SHAPED 15 UL R501 0010274 METAL FILM RESISTOR 1W10O±1% SHAPED 12.5 R509...
Page 50
MATERIAL MATERIAL NAME SPECIFICATIONS LOCATION CODE 0390340 VERTICAL INDUCTOR 10uH ±10% 5A 12.5×26.5 10mm L506 0410010 CHOKE COIL VERTICAL 10UH 1A 5mm L505 0410011 CHOKE COIL VERTICAL 10UH 2A 5mm L503,L504 SWITCH POWER 0460533 @SE2135 UL T501 TRANSFORMER SWITCH POWER 0460441 BCK-40-0726 T502...
Page 51
MATERIAL MATERIAL NAME SPECIFICATIONS LOCATION CODE 2300033 FUSE @T3.15AL 250V VDE F501 3020402 FUSE HOLDER BLX-2 F501 3580086 HEAT RADIATION BOARD 11×15×25 BLACK SINGLE HOLE D510,D511 3580091 HEAT RADIATION BOARD 11×15×31 LFDR9905 U504 3580156 HEAT RADIATION BOARD 40×20×35 DVR938-2 U505 4000453 SELF-TAPPING SCREW BT 3×8H WHITE NICKEL D510,D511,U504...
Page 55
MATERIAL MATERIAL NAME SPECIFICATIONS LOCATION CODE 0880445 4558C DIP N100 0881743 F4558 DIP N100 1980030 MICROPHONE SOCKET CK3-6.35-19 MIC100 5P280 2.5 2 PIN 3P SHIELD,WITH L 2150259 FLAT CABLE XP104 NEEDLE,THE SAME DIRECTION 1563411 9530-2 SURFACE CONTROL BOARD 2100003 CONNECTED CORDS F0.6 SHAPED 7.5mm J5,J6,J7 2100004 CONNECTED CORDS...
Page 56
3850063 ANODE SPRING RC019-01 3# 3850064 CATHODE SPRING RC019-01 3# 3850065 ANODE CATHODE SPRING RC019-01 3# CONDUCT GLUE OF REMOTE 4630900 ABS535T(RU) CONTROL GLUE BAG FOR 5070809 70×230×0.05 PE ENVIRONMENTAL PROTECTION SURFACE STICKER OF REMOTE 5155307 ABS535T(RU) CONTROL 5154411 BOTTOM CASING LABEL...
Page 60
SPECIFICATIONS GLUE BAG FOR ENVIRONMENTAL PROTECTION 5071032 1100×740×0.05 PE ENGLISH (WITH HOLE) 5142076 SN LABEL CURRENCY FOR RUSSIA 5180181 STICKER BBK ENGLISH 25×10 2# 5193737 USER MANUAL ABS535T(RU) ENGLISH/RUSSIA 5210336 WARRANTY CARD CURRENCY FOR RUSSIA 3# 5231504 MICROPHONE SPONGE 226×90×56...
Page 61
MATERIAL CODE MATERIAL NAME SPECIFICATIONS 5230022 SEALING PAPER COLORLESS 5230452 FIBRE ADHESIVE TAPE 18mm 5231454 HIGH TEMPERATURE MASKING PAPER LENGTH:15 YARD WIDTH:6mm 5231455 HIGH TEMPERATURE MASKING PAPER LENGTH:15 YARD WIDTH:12mm 5231456 HIGH TEMPERATURE MASKING PAPER LENGTH:15 YARD WIDTH:24mm 5231514 HIGH TEMPERATURE MASKING PAPER LENGTH:15 YARD WIDTH:20mm...
Need help?
Do you have a question about the ABS535T and is the answer not in the manual?
Questions and answers