Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Blaupunkt BP-FD-CCP400
Summary of Contents for Blaupunkt BP-FD-CCP400
- Page 1 User Manual 4 ZONE FIRE ALARM CONTROL PANEL BP-FD-CCP400...
-
Page 2: System Overview
Advanced Analogue Conventional Fire Alarm Control Panel 1 System overview The BP-FD-CCP400 fire alarm panel has the following characteristics: 1.1 System Capabilities List 1.1.1 Maximum number of Analogue Conventional Detector Inputs: 20 detectors each zone 1.1.2 Available Options: 2-4 Zones 1.1.3... - Page 3 Advanced Analogue Conventional Fire Alarm Control Panel Figure 2. Interface board Components identification...
- Page 4 Advanced Analogue Conventional Fire Alarm Control Panel 1.3 Accessories connection Figure 3 . Output terminals...
-
Page 5: System Installation
Advanced Analogue Conventional Fire Alarm Control Panel Figure 4 . Detectors connection Figure 5. Wrong connection of sounders 2 System installation Prepare the site: Make sure the installation location is free from construction dust, debris and 2.1 Installation checklist other extreme temperature ranges and relative humidity. 2.1.1 Unpack the equipment. -
Page 6: Installing The Cabinet
Advanced Analogue Conventional Fire Alarm Control Panel Review wire routing: See page 5. Connect the field wiring: See Figure 5. 2.1.5 Check for opens, grounds, and shorts before connecting. 2.1.6 Connect batteries. 2.1.7 Connect ground then AC power, we strongly suggest connect mains power by minimum of 2.1.8 16AWG(1.3mm ) wire. -
Page 7: Mains Connection
Advanced Analogue Conventional Fire Alarm Control Panel Figure 7 . 2-4 Zones panel installation diagram Use the terminal (Item 1 in Figure 2) to connect the AC power cable to the panel. Ensure that the power cable is 2.3 Mains connection safe to handle (has no power). -
Page 8: Battery Installation
Advanced Analogue Conventional Fire Alarm Control Panel Figure 8. Mains connection (Ensure that there is no power when connect this terminal!) The panel uses two lead acid gel 12V/2.3Ah batteries connected in series. Connect the batteries with the supplied 2.4 Battery installation free lead and the batteries to the power supply unit with the red (positive) and black (negative) wires. -
Page 9: Initial Power-Up
Advanced Analogue Conventional Fire Alarm Control Panel Fault detection setting Figure 10. Check and confirm all the wires are connected well. Back to the interface board, which has 2 rocker switches, 2.7 Initial Power up the right one is mains switch (Item 2 in Figure 2), the other one is battery switch (Item 6 in Figure 2). If use battery only, turn battery switch on. - Page 10 Advanced Analogue Conventional Fire Alarm Control Panel inside. For any disablement condition, corresponding “disable” lights and “General Disable” lights will lit. 3.1.3 Disablement indication Panel also have another 4 buttons: Test and Reset/ Evacuate/ Panel Buzzer Silence/Remote sounder silence, 3.1.4 Indication of operation when touch off, the LED belongs to lights and trigger corresponding outputs.
-
Page 11: Zone Disable
Advanced Analogue Conventional Fire Alarm Control Panel to return to standby mode. So, it is required to press the “Reset/Test” button, then all information before will be cleared, if �ire alarm signal comes still exist, panel will enter to alarm again. During reset, detectors have no power. Press to silence the remote bells and strobes. -
Page 12: Batteries Maintenance
Advanced Analogue Conventional Fire Alarm Control Panel Records of all testing and maintenance shall be kept as required by the authority having jurisdiction. 6.1.2 Required tools: Slotted screwdriver, insulated 6.1.3 Cross screwdriver, insulated 6.8K Ohm, 1 W resistors D. 470 Ohm, 1W resistors 1N4007 diode Wire stripper Digital multimeter... - Page 13 Advanced Analogue Conventional Fire Alarm Control Panel Appendix A: Weight weight Weight Panel with battery without battery 2-4 Zones Panel 4.6 Kg 2.9 Kg Table 2 . Weight Appendix B: Record Name: Installed by Company:___________________________________________________________ Address:____________________________________________________________ Phone: Company: For service contact Address: Phone: Date:...
- Page 14 Tell: +381 11 318 68 68 o ce@securityshop.rs Imported/Distributed by Security Shop doo BLAUPUNKT and the BLAUPUNKT logo are trademarks of TALISMAN BRANDS (Luxembourg) S.A.R.L. and are used under license from Talisman Brands, Inc. BLAUPUNKT licensees are solely responsible for the BLAUPUNKT branded products manufactured, distributed and sold under license.
Need help?
Do you have a question about the BP-FD-CCP400 and is the answer not in the manual?
Questions and answers