Advertisement
XPM-01 Motion Sensor Manual
Part number: XPM-01
Description
The XPM-01 is designed to fit seamlessly in the corner or the
room or alongside a wall/door. When the PIR senses motion it
transmits an alarm notification to the panel.
Important safety instructions–
Before you install this sensor, be sure to:
Read, keep, and follow all instructions.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
When there is a low battery, replace with a compatible
lithium ion battery.
Installation
Note: We recommend adding the motion sensor to a panel
before installation. Step 4 shows how to pair with a panel.
The motion sensor can be installed using the provided
adhesive and/or screws.
© 29DEC19 SyberSense
Note: We recommend using the provided screws for
installation. This method is more secure than using adhesive
alone.
To install the motion sensor:
1.
Select the desired position for the sensor.
Note: The sensor only detects motion within 3.28 ft (1m)
in front of it (installed at 6.88 ft (2.1m) having a range of
32.80 ft (10m).
2.
Remove the sensor's battery pull tab.
3.
Adhere the sensor to the wall using the provided screws or
adhesive.
Note: We recommend using the provided screws for
installation. This method is more secure than using
adhesive alone.
Screws
a.
Locate the bottom of the sensor (the slotted flat
end), and then use a screwdriver to remove the
casing's screw.
b.
Gently slide a fingernail/fingertip into the slot and
push the top casing of the sensor upward.
1 / 6
DOC ID – 1706 • Rev 01
Advertisement
Table of Contents
Related Manuals for SyberSense XPM-01
Summary of Contents for SyberSense XPM-01
- Page 1 Description Screws The XPM-01 is designed to fit seamlessly in the corner or the Locate the bottom of the sensor (the slotted flat room or alongside a wall/door. When the PIR senses motion it end), and then use a screwdriver to remove the transmits an alarm notification to the panel.
- Page 2 Once the sensor is configured as desired, press the sensor cover against the base, until there is an audible snap. Note: Once placed the sensor cannot be moved without damaging the adhesive. © 29DEC19 SyberSense 2 / 6 DOC ID – 1706 • Rev 01...
- Page 3 Battery replacement learning mode, then pressing the button on the side of the The XPM-01 requires a CR123A battery. Once the battery is sensor to pair the sensor to the panel. low, the panel displays a low battery icon next to the sensor in the devices list.
-
Page 4: Pin Function
(1) Pet immunity pins (3) Sensitivity pins (2) Tamper switch (4) Battery Gently press the jumper on the desired pin set. See Table 1: Pin configuration, on page 4. © 29DEC19 SyberSense 4 / 6 DOC ID – 1706 • Rev 01... -
Page 5: Specifications
Gently press the jumper on the desired pin set. Replace the sensor plate, and then continue to installation. – or – Adjust the pet immunity level, and then and then continue to installation. © 29DEC19 SyberSense 5 / 6 DOC ID – 1706 • Rev 01... -
Page 6: Regulatory Information
European Union 1999/5/EC (R&TTE directive): Hereby, Syber directives Sense declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. © 29DEC19 SyberSense 6 / 6 DOC ID – 1706 • Rev 01...
Need help?
Do you have a question about the XPM-01 and is the answer not in the manual?
Questions and answers