Table of Contents
Advertisement
Quick Links
ELECTRIC HUB MOTOR SCOOTER
NOTE: The unit must be traveling at least 3 mph (5 km/h) before motor will engage.
Kick to start to at least 3 mph (5 km/h) while applying the throttle to engage motor.
OWNER'S MANUAL
Read and understand this entire manual before allowing
NOTE: Manual illustrations are for demonstration purposes only.
Illustrations may not reflect exact appearance of actual product.
Specifications subject to change without notice.
Please have your product along with the 19 character product I.D. code with you
before contacting Razor for warranty assistance and/or replacement parts.
Product I.D. Code: _____________ - ____________ - ____________
child to use this product!
www.razor.com/mx
Hecho en China
Advertisement
Table of Contents
Related Manuals for Razor Power Core XLR 100
Summary of Contents for Razor Power Core XLR 100
- Page 1 Illustrations may not reflect exact appearance of actual product. Specifications subject to change without notice. Please have your product along with the 19 character product I.D. code with you before contacting Razor for warranty assistance and/or replacement parts. Product I.D. Code: _____________ - ____________ - ____________ www.razor.com/mx...
-
Page 2: Table Of Contents
CONTENTS Safety Warnings .....................1-2 Usage .........................7 Before You Begin ....................3 Repair and Maintenance ................8-10 Assembly and Set-Up ..................4 Troubleshooting Guide ..................11 Charging the Battery ..................5 Electric Scooter Parts..................12 Pre-Ride Checklist .....................6 SAFETY WARNINGS Do not activate the throttle unless you are on the scooter and in a safe, WARNING: Riding an electric scooter does present potential risks outdoor environment suitable for riding. -
Page 3: Safety Warnings
SAFETY WARNINGS USING THE CHARGER The charger supplied with the electric scooter should be regularly examined for damage to the cord, plug, enclosure and other parts. In the event of such damage, the scooter must not be charged until the charger has been repaired or replaced. -
Page 4: Before You Begin
ELECTRIC SCOOTER. The scooter MAKE SURE POWER SWITCH IS TURNED “OFF” BEFORE CONDUCTING ANY ASSEMBLY OR has been built to certain Razor MAINTENANCE PROCEDURES. design specifications. The original equipment supplied at the time... -
Page 5: Assembly And Set-Up
ASSEMBLY AND SET-UP Attaching the Handlebars WARNING: Do not attempt Required Tool: 5 mm Allen Wrench (included) to thread the stem into the front fork thread. Note: Make sure any cables/wires are out of the way before inserting the stem into the fork. WARNING: Failure to properly tighten the collar clamp may allow the handlebars to... -
Page 6: Charging The Battery
CHARGING THE BATTERY Your electric scooter may not have a fully charged battery; therefore you must charge the battery prior to use. WARNING: Use ONLY • Initial charge time: 12 hours. • Make sure the power switch is turned OFF when with the recommended charger. -
Page 7: Pre-Ride Checklist
PRE-RIDE CHECKLIST Brake Safety Gear Check the brake options for proper function. When you Always wear proper protective gear, such as an approved safety squeeze the brake lever (on handlebar) or step on the rear- helmet. Elbow pads and kneepads are recommended. Always fender brake, the brake should provide positive braking action. -
Page 8: Usage
For controlled stops, apply the brake by pressure on the rear-fender brake or squeezing the front brake lever (on The brake is capable of skidding handlebar). Razor recommends that you practice applying the brake options at various speeds and in an open area the rear tire and throwing an free from obstructions before riding your scooter around others. -
Page 9: Repair And Maintenance
REPAIR AND MAINTENANCE Turn power switch “OFF” before beginning repair or maintenance: • Read the instructions. • Secure the unit under repair. • Contact Razor customer service if unsure about any repair or • Remove charger plug. • Exercise caution around maintenance. - Page 10 REPAIR AND MAINTENANCE Disconnect battery. To replace the battery, reverse Disconnect motor cables. steps 1-3. Note: When re-inserting the motor wires into the connector, make sure the red wire connects to the blue Black wire and the black wire connects to the brown wire.
-
Page 11: Battery Care And Disposal
Refer to the disposal instructions at left. If acid Disposal: Your Razor product uses a sealed lead-acid battery which must be recycled or disposed of in an comes into contact with skin or eyes, environmentally safe manner. Do not dispose of a lead-acid battery in a fire. The battery may explode or leak. Do not flush with cool water for at least 15 dispose of a lead-acid battery in your regular household trash. -
Page 12: Troubleshooting Guide
TROUBLESHOOTING GUIDE *Unit(s) should be turned OFF and fully charged prior to doing any troubleshooting. NOTE: All troubleshooting steps should be performed by an adult only. Problem Possible Cause Solution Does not work out of the box Unit must be traveling at least Kick to start to at least 3 mph (5 km/h) while pressing down on 3 mph (5 km/h) before motor will engage the thumb throttle to engage motor. -
Page 13: Electric Scooter Parts
ELECTRIC SCOOTER PARTS Keep your scooter running for years with genuine Razor parts. Visit our website or e-mail us for more information on spare part availability. (Specifications subject to change without notice.) 1. Handlebar Grips (Right/Left) 10. Rear-Fender Brake 2. Throttle 11. -
Page 14: Fcc Compliance
Printed in China for Razor USA LLC. Copyright © 2003-2025 Razor USA, LLC. All rights reserved. Razor® and the Razor logo design are among the registered trademarks of Razor USA LLC in the United States and/or select foreign countries. Power Core™ and the Power Core™ XLR 100 logo design are trademarks of Razor USA LLC.
Need help?
Do you have a question about the Power Core XLR 100 and is the answer not in the manual?
Questions and answers