Smok RPM80 Manual

Package Contents:

1. SMOK RPM80 Device (3000mAh built-in battery)
2. RPM Pod (5mL capacity, compatible with RPM coils)
3. RGC Pod (5mL capacity, compatible with RGC coils)
4. RPM Mesh 0.4Ω Coil (Pre-installed for DTL vaping)
5. RGC Conical Mesh 0.17Ω Coil (For Sub-Ohm DTL vaping)
6. USB Charging Cable
7. User Manual

Getting Started

Charge the Device:

• Use the USB cable to fully charge the RPM80 before first use.
• The screen will display charging progress and indicate when fully charged.

Prepare the Pod:

• Choose the pod you wish to use:
  • RPM Pod for RPM coils.
  • RGC Pod for RGC coils.
• Insert the appropriate coil into the pod:
  • Push the coil into the bottom of the pod until it fits snugly.

Fill the Pod:

• Open the silicone plug located on the side of the pod to access the filling port.
• Fill the pod with your preferred nicotine-free e-liquid, avoiding overfilling.
• Close the silicone plug securely to prevent leaks.
• Let the pod sit for 5-10 minutes to allow the coil to fully saturate.

Attach the Pod to the Device:

• Align the pod with the top of the RPM80 and press it into place. Magnets will hold it securely.

Turn On the Device

• Press the fire button five times quickly to turn the device on or off.

Using the Device

Adjust the Wattage:

• Use the "+" and "-" buttons to adjust the wattage (range: 1W–80W).
• Start with a lower wattage and gradually increase to match the coil's recommended range (printed on the coil).

Airflow Adjustment (RGC Pod):

• For the RGC Pod, rotate the airflow control ring at the base to adjust the airflow:
  • Open for direct-to-lung (DTL) vaping.
  • Partially closed for restricted DTL vaping.

Monitor the Display Screen:

• The screen displays:
  • Wattage Setting
  • Battery Level
  • Coil Resistance
  • Puff Counter

Vape:

• Press and hold the fire button while inhaling through the mouthpiece. Release the button after each puff.

Monitor E-Liquid Level:

• Regularly check the pod to ensure it has enough e-liquid to prevent dry hits.

Maintenance and Care

Replace the Coil:

• Replace the coil when you notice reduced flavor, vapor production, or a burnt taste.
• Follow the steps in "Prepare the Pod" to remove and replace the coil.

Clean the Pod:

• Rinse the pod with warm water and let it dry completely before refilling.

Clean the Device:

• Wipe the exterior with a soft, dry cloth to remove dust or e-liquid residue.
• Clean the pod connection area regularly.

Troubleshooting

No Vapor Production

• Ensure the device is powered on, the pod is securely attached, and the coil is properly installed.
• Check that the battery is charged.

Leaking E-Liquid

• Ensure the pod is not overfilled and the silicone plug is sealed tightly.

Burnt Taste

• Replace the coil and ensure the coil is primed before use.

Device Not Powering On

• Recharge the device fully and check the USB cable and power source.

Enjoy your SMOK RPM80 Kit - 7 Color Resin for a versatile and satisfying nicotine-free vaping experience.
Use responsibly and follow all safety precautions!

Safety Guidelines

• Use only recommended e-liquids with the appropriate VG/PG ratio (e.g., 70/30 VG/PG for sub-ohm vaping).
• Do not expose the device to water, heat, or direct sunlight.
• Always ensure coils are fully saturated with e-liquid before use to avoid burning.
• Charge only with the provided USB cable and a compatible power source.
• Keep out of reach of children and pets.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Smok RPM80 Manual