Related Manuals for Toro Flex-Force Power System 4 AMP 60V MAX 2-Pod
Summary of Contents for Toro Flex-Force Power System 4 AMP 60V MAX 2-Pod
- Page 1 Form No. 3466-767 Rev C Flex-Force Power System ® 4 AMP 60V MAX 2-Pod Battery Charger Model No. 86924—Serial No. 324000000 and Up *3466-767* Original Instructions (EN)
- Page 2 Introduction This charger is intended to be used by homeowners and professional operators. Flex-Force 60V lithium-ion battery packs are designed to be charged only by Flex-Force 60V lithium-ion battery chargers. This charger is designed to charge only Flex-Force 60V lithium-ion battery packs. It is not designed to charge any other batteries.
- Page 3 Whenever you need service, genuine manufacturer parts, or additional information, contact an Authorized Service Dealer or distributor, or the tool manufacturer’s Customer Service, and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product.
- Page 4 Safety-Alert Symbol The safety-alert symbol (Figure 2) shown in this manual and on the machine identifies important safety messages that you must follow to prevent accidents. g000502 Figure 2 Safety-alert symbol The safety-alert symbol appears above information that alerts you to unsafe actions or situations and is followed by the word DANGER, WARNING, or CAUTION.
- Page 5 Safety IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS—This manual contains important safety and operating instructions for Flex-Force 60V lithium-ion battery packs and Flex-Force 60V lithium-ion battery chargers. Before using the battery charger or battery pack, read all the instructions and cautionary markings on the battery charger, battery pack, and product using the battery pack.
- Page 6 III. Operation Charge the battery pack with only the battery charger specified by the tool manufacturer. A charger suitable for 1 type of battery pack may create a risk of fire when used with another battery pack. Charge the battery pack in a well-ventilated area only. Follow all charging instructions and do not charge the battery pack outside of the temperature range specified in the instructions.
- Page 7 Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal161-3797 161-3797 1. Do not dispose of improperly 3. For indoor use only 2.
- Page 8 decal161-3793 161-3793 1. Charging mode 4. The battery pack is over button or under the appropriate temperature range. 2. The battery 5. Battery pack pack is fully charging fault charged. 3. The battery pack is charging.
- Page 9 Product Overview Specifications Battery Charger Model 86924 Type 60V MAX 2-Pod Lithium-Ion Battery Charger Input 220 to 240V AC ~4.7A 60Hz, Output 60V DC 4A MAX Appropriate Temperature Ranges Charge battery pack at 5°C (41°F) to 40°C (104°F)* Use battery pack at -30°C (-22°F) to 49°C (120°F) Store battery pack/charger at 5°C (41°F) to 40°C (104°F)*...
- Page 10 Operation Charging the Battery Pack Important: The battery pack is not fully charged when you purchase it. Before using the tool for the first time, place the battery pack in the charger and charge it until the LED display indicates the battery pack is fully charged.
- Page 11 Note: During normal operation, a fan sound is audible from the charger while the battery pack is charging. If multiple battery packs are connected to the charger, you can switch between batteries or charge both at the same time by pressing the charging mode button on the side of the charger.
- Page 12 Important: The battery can be left on the charger for short periods between uses. If the battery will not be used for longer periods, remove the battery from the charger; refer to Storage (page 12). Maintenance Maintenance and servicing are not required under normal conditions. When you clean the surface of the equipment, wipe it only with a dry cloth.
- Page 13 Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself. Problem Possible Cause Corrective Action The battery charger is not 1.
- Page 14 Problem Possible Cause Corrective Action The LED fault indicator 1. There is an error in 1. Remove the battery light on the battery charger the communication pack from the battery is blinking red. between the battery charger, unplug the pack and the charger. battery charger from the outlet, and wait 10 seconds.
- Page 15 Notes:...
- Page 16 Notes:...
Need help?
Do you have a question about the Flex-Force Power System 4 AMP 60V MAX 2-Pod and is the answer not in the manual?
Questions and answers