Advertisement
Advertisement
Table of Contents
Related Manuals for HuTools DKS01
Summary of Contents for HuTools DKS01
- Page 1 DKS01 Digital Deadbolt Lock...
-
Page 2: Installation Overview
Installation Overview Install the physical lock ( age 2 Detect door orientation ( age ) Change the default master code ( age 1 ) Customize setting ( age 1 Important tips to ensure a successful installation: l ays reset your lock after installation. Do not use electric drill to tighten scre s. -
Page 3: Parts List
Parts List Strike eypad Mounting Latch ssembly late attery Interior Latch Strike Interior ssembly Co er ssembly Scre s Scre s G x 2 J x 1 Mounting late Scre s ackup eys I x 2 K x 2 NO ELECTRIC DRILLS TOOL RE IRED... -
Page 4: Installation Instructions
Installation Instructions Door Measurements 8 or 2 2 1 8 54 mm 8 to 2 5 mm to 5 mm 25mm Adjust Latch Backset Backset: The distance from door edge to center of hole on door face. or 2 backset rotate the latch to extend latch. (70mm) or 2 backset no ad ustment is needed. - Page 5 Installation Instructions (Continued) Install the Latch Do not o ertighten scre s. Install Strike on the door frame Make sure hole in door frame is at least 1''(25mm) deep. Check Alignment ith the door closed check alignment bet een the latch and the strike plate making sure hen the deadbolt is extended it is going into the bolt hole and not hitting the deadbolt...
- Page 6 Installation Instructions (Continued) Install Keypad Assembly unlocked o not insert the physical key until lock is completely installed. Install Mounting Plate Keep parallel to door edge. unlocked Do not o ertighten scre s.
- Page 7 Installation Instructions (Continued) Install Interior Assembly Connect the cable by pushing connector in firmly until it Don't put is completely batteries seated . in yet. ertical unlocked Check deadbolt operation by turning the thumbturn back and forth. If thumbturn doesn't rotate, repeat steps 8c and apply much more force.
- Page 8 Detect door orientation / Factory reset l ays reset your lock after installation. The motor ill not operate before completing the step. Install batteries. unlcoked Use ne , non rechargeable Alkaline ertical batteries only and do not mix old and ne batteries. ress and hold the Reset button ith a reset pen or a paper clip and proceed to the...
-
Page 9: Program & Use
Program & Use UNLOCK from outside LOCK from outside 1 Press any key to activate. · Press and hold any key for seconds. · 2 Enter Master code / User code. Enable Auto ock ( ee page 3 Press to confirm. LOCK &... - Page 10 Program & Use (Continued) Wrong Entry Limit · After 0 unsuccessful attempts at entering a valid access code, the lock ill shut do n for minutes. Unlock with Fake code User can prevent pin code exposure from strangers by entering random digits before or after pin code.
- Page 11 Program & Use (Continued) Important Tips: · uring a programming steps, the button turns green to indicate that you can proceed. Please proceed to the next steps before the green light goes off. · If you hear rapid beeps ith ashing red lights, it indicates entry error.
- Page 12 Program & Use (Continued) Disable Silent Mode Master Code Enable Auto Lock Automatically locks the deadbolt 0 seconds after unlocking. • his feature is off by default. Master Code Disable Auto Lock Master Code Set Auto Lock Time Delay ou can set the Auto ock time delay bet een 0 and seconds.
-
Page 13: Factory Default Settings
Program & Use (Continued) Factory Default Settings actory efaut ettings Master Code Auto ock isabled ilent Mode isabled rong Code Entry imit 0 times acation Mode isabled How To Reset y performing the steps belo , you ill teach the lock the orientation of your door and delete all User Codes associated ith the lock. -
Page 14: Troubleshooting
Troubleshooting Solutions When Issues refers to the latch does not extend but I CAN hear the motor turning. A; B; C; D the latch does not extend and making any sound. Reset I lost all the preset codes after door handing. I received 6 rapid beeps when programming. - Page 15 Troubleshooting Solutions The latch and strike are misaligned, causing the latch to bind. · Adjust the position of the strike plate on latch bolt. · Make sure you reset the lock with the door opened. · Do not over tighten screws. Clear residual charge: take out all batteries and unplug power cable wire;...
Need help?
Do you have a question about the DKS01 and is the answer not in the manual?
Questions and answers