Related Manuals for L&S Mec Driver
Summary of Contents for L&S Mec Driver
- Page 1 Mec Driver - Radio / Zigbee control Frequency range: Transmission power: IP20 L&S Deutschland GmbH . Daimlerring 34 . D-32289 Rödinghausen . www.ls-deutschland.de MA 755400022...
- Page 2 DE - Vereinfachte EU-Konformitätserklärung HR - Pojednostavljena Izjava o sukladnosti s propisima Europske unije Hiermit erklärt L&S Deutschland GmbH, dass der Funkanlagentyp 4708079 / Ovim dokumentom tvrtka L&S Deutschland GmbH izjavljuje da tip bežičnog 4708080 / 5991777 der Richtlinie 2014/53/EU entspricht. Der vollständige Text uređaja 4708079 / 4708080 / 5991777 ispunjava zahtjeve Direktive 2014/53/EU.
-
Page 3: Table Of Contents
Content Dimensions ..............................4 Emotion / Single Color ..........................5 Connecting the components ........................6 Direct connection (without ZigBee network) ....................8 Connection with ZigBee Bridge (Smart Home) ..................12 Factory settings ............................18 Troubleshooting ............................20 L&S Deutschland GmbH . Daimlerring 34 . D-32289 Rödinghausen . www.ls-deutschland.de... -
Page 4: Dimensions
Dimensions r e l r a l i t s r h e e t y s a f i s e a t i S i c o r m h i n r a l r e l i n f i t s r h e... -
Page 5: Emotion / Single Color
Emotion / Single Color Setting for Emotion or Single Color LEDs via DIP switch Attention! Check and adjust before commission- ing! If changes are made later, the receiver must be briefly disconnected from the mains voltage. Status LED Button Function Selected luminaire group OFF Selsected luminaire group ON Change color temperature... -
Page 6: Connecting The Components
Connecting the components L&S Deutschland GmbH . Daimlerring 34 . D-32289 Rödinghausen . www.ls-deutschland.de... - Page 7 Connecting of components L&S Deutschland GmbH . Daimlerring 34 . D-32289 Rödinghausen . www.ls-deutschland.de...
-
Page 8: Direct Connection (Without Zigbee Network)
Direct connection (without ZigBee network) L&S Deutschland GmbH . Daimlerring 34 . D-32289 Rödinghausen . www.ls-deutschland.de... -
Page 9: Teaching The Remote Control
Direct connection Teaching the remote control 1. Place the receiver module and remote control close together. The distance must be less than 15 cm for as long as the teach-in process lasts. 2. Press the button for the selected lumi- naire group on the remote control. -
Page 10: Reset Receiver
Direct connection Disconnect remote control from luminaire group 1x grün 1x green ~ 5 Sek. ~ 5 sec. Press the button for the selected luminaire group for approx. 5 seconds until the status LED on the remote control lights up green once. The receiver is now disconnected. Reset receiver Press and hold the button on the receiver for approx. - Page 11 L&S Deutschland GmbH . Daimlerring 34 . D-32289 Rödinghausen . www.ls-deutschland.de...
-
Page 12: Connection With Zigbee Bridge (Smart Home)
Connection with ZigBee Bridge (Smart Home) L&S Deutschland GmbH . Daimlerring 34 . D-32289 Rödinghausen . www.ls-deutschland.de... - Page 13 Connection with ZigBee Bridge (Smart Home) Reset receiver Press and hold the button on the receiver for approx. 5 seconds. ~ 5 Sek. ~ 5 sec. The connected LEDs light up once. Set the remote control to teach-in mode ~ 5 - 11 Sek. ~ 5 - 11 sec.
- Page 14 Connection with ZigBee Bridge (Smart Home) Connect with App Open the Zigbee App. Search for new lights. Follow the instructions in the app. Light setup Add light Search Settings Wait until the remote control and receiver are recognized: - The status LED of the remote control flashes green once and goes out as soon as the remote control is recognized.
- Page 15 Connection with ZigBee Bridge (Smart Home) grün green green ~ 10 sec. ~ 10 Sek. / sec. 3. Press the ON button for approx. 10 seconds until the status LED on the remote control lights up green once. (In the meantime, the status LED flashes red several times and the connected LEDs light up twice).
- Page 16 Connection with ZigBee Bridge (Smart Home) Disconnect remote control from lighting group 1x grün 1x green ~ 5 Sek. ~ 5 sec. Press the button for the selected luminaire group for approx. 5 seconds until the status LED on the remote control lights up green once.
- Page 17 L&S Deutschland GmbH . Daimlerring 34 . D-32289 Rödinghausen . www.ls-deutschland.de...
-
Page 18: Factory Settings
Factory settings L&S Deutschland GmbH . Daimlerring 34 . D-32289 Rödinghausen . www.ls-deutschland.de... - Page 19 Factory settings Reset remote control to factory settings 60 Sek. 60 sec. ~ 5 sec. ~ 5 Sek. Press the OFF button for approx. 5 seconds. The status LED on the remote control flashes red for 60 seconds. Wait until the status LED goes out. The remote control is now reset to the factory settings. Reset receiver to factory settings Press and hold the button on the receiver for approx.
-
Page 20: Troubleshooting
Troubleshooting General / Direct connection Error Reason Solution The remote control and receiver cannot Distance between receiver and remote Reduce the distance to a maximum of be connected. control too large. 15 cm. Teach-in procedure was not carried out First press the button on the remote correctly. - Page 21 Troubleshooting Search for the corresponding lamp in the app Error Reason Solution Recipient is not found in the app. Distance to the ZigBee Bridge is too Reduce the distance between the high. receiver and the ZigBee Bridge. Receiver was not reset. Press the button on the receiver for approx.
- Page 22 Troubleshooting Light does not respond (ZigBee app). No reception to the Zigbee Bridge. Make sure that the end device and receiver are connected to the ZigBee Bridge via WLAN. Wrong lamp selected. Select the correct lamp in the app. Receiver not recognized as a lamp in Execute the search in the app again.
- Page 23 L&S Deutschland GmbH . Daimlerring 34 . D-32289 Rödinghausen . www.ls-deutschland.de...
-
Page 24: Operation
Operation Status LED Function Short press Long press Selected group OFFS Selected group ON Gradual color Stepless color Change color temperature change in x change steps Dimming in x Dimming Stepless dimming steps 1, 2, 3, 4 Select luminaire group Select group L&S Deutschland GmbH .
Need help?
Do you have a question about the Mec Driver and is the answer not in the manual?
Questions and answers