Advertisement
Table of Contents
Advertisement
Table of Contents
Related Manuals for Technicolor OWA0111
Summary of Contents for Technicolor OWA0111
- Page 1 OWA0111 Quick Setup Guide...
-
Page 2: Before You Start
1. Before you start • Carefully read the Safety Instructions and Regulatory Notices document included in your package before continuing with the installation of your OWA0111. • Do not make any connections until instructed to do so! 2. Check the content of your box... -
Page 3: Top Panel
3.2. Top panel WPS button and Status LED (item A) The WPS button on the top panel of your OWA0111 is used to pair the OWA0111 with other Wi-Fi devices and the Status LED on the side of WPS button informs you about the status of your OWA0111. - Page 4 3.3. Back panel and bottom product label Reset button (item A) When the OWA0111 is powered on and you press the Reset you can restart or reset “5.8. How to repair an unresponsive Wi-Fi extender” on it. For more information, see page 11.
- Page 5 OWA0111 and then plug the other end into a nearby power outlet. 3 Press the power ( ) button on the back of the OWA0111. The Status LED will first be solid yellow during startup, then turns green. If this is not the case, check the connections you made.
- Page 6 ) of the OWA0111 and then plug the other end into a nearby power outlet. 3 Press the power ( ) button on the back of the OWA0111. The Status LED will first be solid blue during startup. 4 Wait until the Status LED slowly blinks green.
- Page 7 ) of the OWA0111 and then plug the other end into a nearby power outlet. 3 Press the power ( ) button on the back of the OWA0111. The Status LED will first be solid blue during startup. 4 Wait until the Status LED slowly blinks green.
-
Page 8: Tips And Tricks
Make sure your OWA0111 isn’t onboarded already to an existing EasyMesh home network, or paired with another Internet gateway. Procedure 1 Briefly press the WPS ( ) button on the OWA0111. The Status LED on the OWA0111 starts blinking green. - Page 9 Make sure your OWA0111 isn’t joined already to an existing EasyMesh home network. Procedure 1 Briefly press the WPS ( ) button on the OWA0111. The Status LED on the OWA0111 starts blinking green. 2 Within two minutes, briefly press the WPS button on your Internet gateway or any Wi-Fi extender in the EasyMesh home network.
- Page 10 ƒ Another Wi-Fi extender, briefly press its WPS button. ƒ Another type of device, consult the documentation of your device. 3 After some time the Status LED on the OWA0111 turns back to its previous solid state (green, yellow or red). The Wi-Fi connection is now successfully established.
- Page 11 1 Unplug the power supply and move the OWA0111 closer to your access point, or to a place with less obstacles between the OWA0111 and your access point. 2 Plug in the power supply and wait two minutes to allow the OWA0111 to start up all services and evaluate the link quality.
- Page 12 ACCESS KEY printed on the label of your Wi-Fi extender as password. Note: If this is the first time that you sign in, the OWA0111 may offer you to change your password. 4 The Wi-Fi extender web interface appears with all settings available.
- Page 13 2 Use a pen or an unfolded paperclip to push the recessed Reset button on your Wi-Fi extender: shortly (1 to 2 seconds) and then release it to force it to restart. ƒ for at least 10 seconds and then release it to rest it to factory defaults. ƒ...
- Page 14 Technicolor Delivery Technologies – www.technicolor.com *6304400A* Copyright © 2021 Technicolor. All rights reserved. All tradenames referenced are service marks, trademarks, or registered trademarks of their respective companies. Specifications subject to change without notice. 6304400A DMS3-QIG-25-704 v1.2...
Need help?
Do you have a question about the OWA0111 and is the answer not in the manual?
Questions and answers