Subscribe to Our Youtube Channel
Related Manuals for Sony SEG-1
Summary of Contents for Sony SEG-1
- Page 1 SPECIAL-EFFECTS GENERATOR SEG-1 SONY CORPORATION OF AMERICA 2V990769-1 Island City, New York 11101 4747 Van Dam Stnet, Long PRINTED IN USA 373-Printing...
-
Page 2: Table Of Contents
TABLE OF CONTENTS General Description ......Circuit Description ......Transistor Voltage Chart...... -
Page 3: General Description
4, Hirschmann 6 Pin can be driven through Hirschmann connectors. To de- receptacle velop the sync pulse in the SEG-1, Camera #l must al- Monitor video outputs: 1.4V p-p, (dependent ways be connected with composite video signals, while upon input), sync negative,... - Page 4 Two modes of camera drive, external and At one extreme, a transition between channels is internal, are available. In the SEG-1, a two-to- produced at the left side of the screen. At the one interlace sync generator is installed which is other pot extreme, a long (60~µs) pulse is pro-...
-
Page 5: Transistor Voltage Chart
4. 80e Q5 (UJT) E - 2 All voltages above measured with a VTVM. SEG-1 C O N T R O L S E T T I N G S : NOTES: Channel Level Control = Maximum (upper position) Channel B Level Control = Maximum (lower position) -
Page 12: Parts List
4.7 k R68K-l/4-10C 68 k AS-SEG-l-l Signal Processing Board,with com- R2.2K-l/4-10C 2. 2 k ponents and switchbracket R82-l/4-10C RlOK-l/4-1OC AS-SEG-1-2 Sync Generator Board, with com- R3.3K-l/4-10C 3.3 k ponents. R560-l/4-10C 2. 2 k R2.2K-l/4-10C SIGNAL PROCESSING BOARD R680-l/4-10C R E S I S T O R S... - Page 13 S y m b o l Part No. D e s c r i p t i o n R68K-l/4-10C 68 k TR-2N4123 2N4123 " " Rl OK-1/4-l OC 10 k R82-l/4-10C 2N3906 T R - 2 N 3 9 0 6 "...
- Page 14 Symbol Part No. Description CONNECTORS C25M-25-20E 25µF,25WV CN 1,2, Coaxial Receptacles ClOOOP-400-10MY lOOOpF,400WV, CN-SO239 3, 4 10%, mylar CN-MAB6 CN 6,7, Hirschmann 6 pin ClOOM-15-20E lOOµF, 15WV female Receptacles C470P-400-10C 8, 9 470pF, 400WV CN 10 CN-MASE16 Hirschmann 6 pin 10%, ceramic male Receptacles co.
-
Page 15: Supplement
Minor modifications have been made to the circuit boards to Serial No. 1523 and higher. accommodate these changes. Refer to the revised schematic diagram and the SEG-1 Ser- vice Manual. From Serial No. 2000 and higher, the Signal Processing Board has been redesigned as a two-sided printed board. -
Page 20: Mechanical Parts
The following list contains stock numbers for cabinet parts and hardware. Refer to the SEG-1 Service Manual for a complete list of electrical parts. MECHANICAL PARTS Part No. Description Q'ty DWG-V-218-1 Screw, Pan Head (+) #4-40 x l/4 Clear Mylar Washer #4...
Need help?
Do you have a question about the SEG-1 and is the answer not in the manual?
Questions and answers