ZooZ ZEN20 800LR User Manual

Scan to register your product for
extended warranty and more perks.
Z-Wave® on/off control of up to 5 electrical devices
Ÿ
On/off (charging/charged) reports from USB ports to the hub (no Z-
Ÿ
Wave® control) - turn off the charging device for best results
Energy monitoring for each of the 5 outlets
Ÿ
NEW: 800 series Z-Wave® chip for better range and faster control
Ÿ
Z-Wave® Long Range for ultra reliable no-mesh communication
Ÿ
Built-in overload protection and ETL certification
Ÿ
S2 Security and SmartStart for quicker and more secure set-up
Ÿ
Model Number: ZEN20 800LR
Ÿ
Z-Wave® Region: US / CA / MX
Ÿ
Power: 120 VAC
Ÿ
Maximum Load: 15 A total (between 5 outlets)
Ÿ
Maximum Load for USB ports: 2.1 A total (between 2 ports)
Ÿ
Cord Length: 2 feet
Ÿ
Range: Up to 150 feet line of sight (or up to 1300 with Long Range)
Ÿ
Installation and Use: Indoor only
Ÿ
CAUTION
This is an electrical device - please use caution when installing and
operating the power strip. Remote control of appliances may result in
unintentional or automated activation of power. Do NOT use this Z-
Wave® device to control electric heaters or other appliances which
produce the risk of fire, burns, or electrical shock when unattended.
Plug the Power Strip into any standard grounded 110 V receptacle. Do
NOT connect any devices to the strip at this point. Turn the power
switch on (the RESET side) and click each of the channels control
buttons to see if the LED indicators come on and off. If the LED
indicators don't light up at all, please try a different receptacle. If they're
still off, please make sure the power switch is on. If the problem persists,
please get in touch with our support team: ask@getzooz.com
BEFORE YOU PLUG ANYTHING IN
Make sure the load you are about to connect does NOT exceed 15 A
in power. This Power Strip can hold up to 15 A in total. It means that the
power of all appliances connected to your ZEN20 at a given time can
NOT exceed 15 A. It doesn't matter if this is just one device connected to
one of the outlets or 5 small appliances plugged into all of the Strip's
outlets.
Connecting heavy duty equipment to this Power Strip will DAMAGE
the device and may cause the connected appliance to malfunction.
Do NOT plug washers, dryers, refrigerators, or motors over 1/3 hp to
any of the outlets on the Power Strip.
S2
This product can be included and operated in any Z-Wave® network with other Z-Wave®
certified devices from other manufacturers and/or other applications. All non-battery
operated nodes within the network will act as repeaters regardless of vendor to increase
reliability of the network.
This product features the latest Security 2 (S2) framework to remove smart home network
hacking risks. This device is equipped with a unique authentication code for trusted
wireless communication.
This is an ETL certified device. ETL, just like UL, is a Nationally Recognized Testing
Laboratory. The ETL mark is proof of product compliance with North American safety
standards.
WARNING
This product should be installed indoors upon completion of any building renovations.
Ÿ
Prior to installation, the device should be stored in a dry, dust-and-mold-proof place.
Ÿ
Do not install the Power Strip in a place with direct sun exposure, high temperature, or
Ÿ
humidity.
Keep away from chemicals, water, and dust.
Ÿ
Ensure the device is never close to any heat source or open flame to prevent fire.
Ÿ
Ensure the device is connected to an electric power source that does not exceed the
Ÿ
maximum load power.
No part of the device may be replaced or repaired by the user.
Ÿ
This product is covered under a 12-month limited warranty or extended 5-
year warranty once registered. To read the full warranty policy or file a
warranty claim, please go to www.getzooz.com/warranty
USER MANUAL
POWER STRIP
ZEN20 800LR
CH 1 CH 2
FEATURES
SPECIFICATIONS
INSTALLATION
Not sure if your equipment can be
safely controlled by the Power Strip?
WARRANTY
CH 3 CH 4 CH 5
www.getzooz.com
ask@getzooz.com
Just ask: ask@getzooz.com