Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DMP X1 Series
Summary of Contents for DMP X1 Series
- Page 1 X1-8 DOOR CONTROLLER INSTALLATION AND PROGRAMMING GUIDE LT-2289 1.01 21131 © 2021...
-
Page 2: Table Of Contents
TABLE OF CONTENTS X1-8 Door Controller Overview ......1 Apply Power ............7 X1 Door Controller Power �����������������������������������������1 Ground the System �����������������������������������������������������7 X1 Door Controller PCB Components ������������������1 Wire AC Power �������������������������������������������������������������7 XD Module PCB Components ��������������������������������2 Wire the Battery ����������������������������������������������������������7 Door Controller Plug-In Terminals ������������������������2 Wire the Modules ��������������������������������������������������������7 Check the Addresses of the Modules ����������������... -
Page 3: X1-8 Door Controller Overview
X1-8 DOOR CONTROLLER OVERVIEW The X1 Series is a cloud-based door access controller that is fully programmed in Dealer Admin™ and maintained in Virtual Keypad™� This guide will cover mounting the system, wiring devices to the system, configuring network options, applying power, programming the system in Dealer Admin, and testing the system�... -
Page 4: Xd Module Pcb Components
X1 and XD Headers R2 W2 G2 B2 DS RX Door Controller Plug-In Terminals Insert Wiring terminals on an X1 Series system is done easily by using the plug-in terminals� Plug In 1� Insert the wire into the slot� 2� Tighten the screw on the bottom�... -
Page 5: Mount The System
MOUNT THE SYSTEM The metal enclosure for the X1 Series must be mounted directly to a wall, backboard, or other flat surface in a secure, dry place to protect the system from damage� Do not remove the PCBs from the enclosure�... -
Page 6: Wire The Inputs
WIRE THE INPUTS Door Switch (DS) Connect a door contact or door position switch to indicate the status of the door, whether it is open or closed� Use this terminal if enabling door prop or door force� This terminal is a Normally Closed input� Request to Exit (RX) Connect a motion sensing device or a mechanical switch to provide RX capability to the system�... -
Page 7: Wire The Electronic Lock
WIRE THE ELECTRONIC LOCK Form C Relay The X1 Series system provides a Form C (SPDT) relay for controlling locks and other electronically-controlled barriers� The three relay terminals marked NO C NC allow you to connect the device wiring to the relay for module control�... -
Page 8: Determine Communication
DETERMINE COMMUNICATION The options in this section are in the DMP-recommended installation order� If an option is not part of your desired application, move to the next option� Ethernet Port Ethernet Connection Connect an Ethernet cable from the LAN/WAN connection to the X1 PCB Ethernet port�... -
Page 9: Apply Power
APPLY POWER Warning: Refer to your local state regulations before connecting to building power� Wiring methods shall be in accordance with NEC, NFPA72, ANSI, and with all Authority Having Jurisdiction Ground the System Be sure to secure the green wire lead Model 505-12 to an earth ground�... -
Page 10: Check The Addresses Of The Modules
Check the Addresses of the Modules The Module address is based on its location in the enclosure� XD 1 - Address 2 X1 - Pre-Addressed to Address 1 R2 W2 G2 DS RX XD 7 - Address 8 XD 2 - Address 3 R2 W2 G2 DS RX R2 W2 G2... -
Page 11: Door Controller Wiring Example
Door Controller Wiring Example The diagram here shows the transformer and the battery wiring� It also shows a possible application with an electronic lock wired normally closed with wet contacts� To 505-12 Power Supply +AC/DC- +BAT- R2 W2 G2 DS RX Jumper Set to Wet White Green... -
Page 12: Module Wiring Example
Module Wiring Example A module wires similarly to a Door Controller, except the module locks must be wired in a dry state with power supplied by the built-in 505-12 5 Amp Power Supply� Wiring from Previous X1/XD R2 W2 G2 DS RX 12VDC White... -
Page 13: Connection Settings
CONNECTION SETTINGS If not connecting over Ethernet, connect to Wi-Fi at this time� If connecting over Ethernet, skip to Configure Network Settings� Configure Wi-Fi Settings On power up, the X1 broadcasts an SSID of DMPX1 followed by the system’s serial number� No password is required to connect to the SSID�... -
Page 14: Program In Dealer Admin
PROGRAM IN DEALER ADMIN After you’ve installed the X1 Series Door Controller and configured basic communication settings, follow the steps in each of the following sections to program a system in Dealer Admin: 1� Sign In to Dealer Admin 2� Add a Customer 3�... -
Page 15: Add An X1
6� Turn on additional options as needed� 7� Press Save� Add Card Formats The first card format for any door is defaulted to DMP� Refer to Card Format Options below when programming card formats� 1� In Card Formats, press the Add icon �... -
Page 16: Enable Video Services
Enable Video Services 1� In Video Services, press the Add icon � 2� Select the types of cameras or NVRs that you want to enable on the system� 3� Select any third-party applications that you want to enable on the system� This allows users to sign in to their services from Virtual Keypad�... -
Page 17: Test The System
TEST THE SYSTEM Make sure that the Reader LED(s) is on and the Door Controller’s Power LED is on� If connected to Wi-Fi, the Wi-Fi LED is on solid� If connected to network, the Network Port light is blinking� For cell and all communication methods, check that Door Controller is communicating with Dealer Admin and Virtual Keypad after Dealer Admin programming is completed�... -
Page 18: Fcc Information
3 Year warranty against defects in materials and workmanship� Visit DMP�com for full details� I N T R U S I O N • F I R E • A C C E S S • N E T W O R K S...
Need help?
Do you have a question about the X1 Series and is the answer not in the manual?
Questions and answers