Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Seada SDC024-B12
Summary of Contents for Seada SDC024-B12
- Page 1 S h o w i n g t h e W o r l d SDC024-B12 (N) 4K PTZ Video Camera User Manual V1.0...
-
Page 2: Copyright Information
COPYRIGHT INFORMATION ⚫ Copying, reproducing or transmitting this file is not allowed if a license is not provided by our company. Unless copying this file is for the purpose of backup after purchasing this product. ⚫ In order to keep improving the product. Our company reserves the right to make changes to product specifications without prior notice. -
Page 3: Symbol Conventions
SYMBOL CONVENTIONS Symbol Description Provides additional information to emphasize or supplement important Explanation points of the main text. Caution indicates that the user is reminded of some important Note operations or to prevent potential injury or property loss. Indicates a potentially hazardous situation which, if not avoided, could ⚠... -
Page 4: Safety Notes - Important
SAFETY NOTES - IMPORTANT ◼ During the installation of this camera, please read this manual carefully and operate strictly. In accordance with the installation instructions. Keep this manual for future reference. ◼ Before powering on the camera, please check the power carefully. Make sure that you are using the right power source. -
Page 5: Table Of Contents
CONTENTS ABOUT THE PRODUCT -------------------------------------------------------------------1 1.1. ---------------------------------------------------------------------------------------------- 1 QUICK GUIDE 1.2. -------------------------------------------------------------------------------------------------------- 1 RTSP FEATURES ------------------------------------------------------------------------------------2 2.1. & ---------------------------------------------------------------------- 2 CHARACTERISTICS FUNCTIONS 2.2. ------------------------------------------------------------------------------- 2 APPLICATION SCENARIOS PRODUCT COMPONENTS ---------------------------------------------------------------3 3.1. & ----------------------------------------------------------------------- 3 LIST OF PARTS ACCESSORIES 3.2. & ----------------------------------------------------------------------------- 4 MAIN PARTS INTERFACES... -
Page 6: About The Product
1. ABOUT THE PRODUCT 1.1 Quick Guide The camera can be accessed and controlled via the following ways: ⚫ WebUI: Camera control, network setting. ⚫ CameraCMS: camera search and control, network setting. ⚫ VLC: watch the camera two streams. ⚫ ONVIF: version 2.1 supported Name: admin Initial password: leave empty ⚫... -
Page 7: Features
2. FEATURES 2.1 Characteristics & Functions ⚫ 1/2.8”4K CMOS, 8.46MP. ⚫ 4K ultra-HD lens, 12x optical zoom, up to 72.5° FOV. ⚫ Built in the industry-leading AI image algorithm for human body detection and locking tracking, which can realize a wide range of automatic detection and continuous tracking. ⚫... -
Page 8: Product Components
3. PRODUCT COMPONENTS 3.1 List Of Parts & Accessories When you open the box, check all accessories according to the packing list. Camera x 1 Remote Controller x 1 RS-232 Cable x 1 Power Adapter x 1 USB x 1... -
Page 9: Main Parts & Interfaces
3.2 Main Parts & Interfaces Front View Rear View Bottom View Interface Interface Camera Module RS232-IN Power Indicator RS232-OUT/RS485 Communication Indicator Power (DC 12V) USB 3.0 Mounting Hole HDMI Locating Hole 3G SDI LINE IN Network... -
Page 10: Remote Control
3.3 Remote Control... - Page 11 Name Function Home Press “HOME” button, camera moves to initial position. Used to switch among 4 cameras, press 1-4 number buttons to Camera control cameras with 1-4 addresses respectively. For example, Selection Button press button 1 to control the camera with address 1. Press “AUTO”...
-
Page 12: Installation
4. INSTALLATION 4.1 Size And Dimension Front Rear Side Bottom... -
Page 13: Installation
4.2 Installation Ceiling or wall mounting brackets can only be mounted on template and concrete wall. For safety reasons, plasterboard is not recommended. 4.2.1 Wall Mount... -
Page 14: Ceiling Mount
4.2.2 Ceiling Mount... -
Page 15: Webui Instruction
5. WebUI Instruction Web Client To Access the Web Client Interface, type the device’s IP address (default = 192.168.5.163) in the address field of your internet browser and press enter to access the Web Client login page. You can log in as a standard user or as an administrator. When logging in as an administrator (Default Username: admin;... -
Page 16: Audio Config
Tracking Config Users can Control PTZ and enable/disable tracking of the camera. Enable and change of tracking height will confirm the activated zone for the camera to track. Users can also change the sensitivity, speed and target lost time of the tracking and decide whether the camera tilts during tracking. -
Page 17: Video Config
Video Config Stream Type: Different video output mode setting, use different streams. (Main stream, Sub stream) Resolution: Set video image resolution. (Main stream default 1920*1080, 640*360, 1280*720 and 3840*2160 as option; Sub stream default 1280*720, 640*320, 1920*1080 as option) Bitrate Type: Set rate control mode. (Main/Sub stream default constants bit rate, variable bit rate as option). - Page 18 Media Config Protocol Port: Change the port for the RTSP protocol. (Default 554) RTMP: Set RTMP stream for camera. NDI Config Enable/Disable NDI function and set up NDI parameters.
-
Page 19: User Manage
Control Protocol Config Enable/Disable: Enable/Disable transparent transmission. Connection Protocol: Choose TCP/UDP protocol. Work Mode: Choose Client or Server. IP: When the camera is set as client, the IP address of the transmitted camera is needed. When the camera is set as server, the IP address can be left as blank. Port: Choose from 1-65535 as transparent transmission port. -
Page 20: Ethernet Config
5.10 Ethernet Config DHCP: Enable or disable obtain IP automatically can be set. IP Address: Set the IP address. (Default 192.168.5.163). Note: This IP address is the same as the one used to login to the Web page. Subnet Mask: Set the subnet mask. (Default 255.255.255.0) Default Gateway: Set the default gateway. -
Page 21: Device Mangement
6. DEVICE MANAGEMENT 6.1 CameraCMS Instruction Install and open CameraCMS on PC, enter the user interface: If the camera and PC are in the same LAN, click Start Search, then search starts and all online devices will be listed, as the picture shown below: To modify the device’s network information, enter the IP address, mask, gateway in the Modify Network column. - Page 22 To control and preview a camera, first choose the device, modify its IP address as the IP address of the same LAN, then click Add To Client as the picture shown below. Please check that all IP addresses are in the same LAN.
-
Page 23: Remote Configuration
6.2 Remote Configuration Choose the camera in the device list, click Remote Configuration to upgrade or config the camera. 6.2.1 Streaming ⚫ Stream Type: Set the parameters of main stream, sub stream. ⚫ Resolution: Set among 4K (3840*2160), 1080P (1920*1080), 720P (1280*720), 360P (640*360), choose resolutions based on actual requirements and capability of device. - Page 24 relatively poor. Vice versa, the larger the fluctuation of the byte will be, the higher the image quality will be. ⚫ Video Coding type: Choose H.264 or H.265. ⚫ Encode Level: Choose from Base, Main and High. ⚫ Channels: STEREO. ⚫...
- Page 25 6.2.2 Network ⚫ Connect With: Choose from Static IP or DHCP address. IP Address: IP address for the camera. ⚫ Mask: Mask address for the camera. ⚫ ⚫ Gateway: Gateway IP address. ⚫ DNS 1: Server-prior, DNS address for the device. ⚫...
- Page 26 6.2.3 RTMP In RTMP1 and RTMP2, main stream, sub stream can be chosen to stream.
- Page 27 6.2.4 Protocol ⚫ Enable / Disable: Enable / Disable transparent transmission. ⚫ Protocol: Choose TCP or UDP protocols. ⚫ Camera As: Choose Client or Server. ⚫ IP: When the camera is set as client, the IP address of the transmitted camera is needed. When the camera is set as server, the IP address can be left as black.
- Page 28 6.2.5 Upgrade Click Upgrade menu to enter the main interface, as the picture shown above. Click … to search and load the updating firmware, then click Upgrade to start upgrading. Do not power off the camera during upgrading. After the upgrading is completed, the camera will reboot.
- Page 29 6.2.6 UP/PW ⚫ Password setting: When a password is required, the camera can be accessed only after a correct password is entered. ⚫ Reboot: Reboot the camera.
- Page 30 6.2.7 UP.PM After selecting the same model of the device to be synchronized that is now managed and unchecked, tick any or more of the video parameters, audio parameters, and trace parameters, and when you click the UP.PM, the device that you are currently synchronizing will synchronize with the source device parameters.
- Page 31 6.2.8 Preview Click Main View to get into camera control and preview part as below. This interface includes three main parts: Device List, Device Control, Video Preview. ⚫ Device: It displays all online cameras added to “Device Management”. ⚫ Device Control: Get control of the selected camera (camera name in blue). ⚫...
-
Page 32: Menu Settings
7. MENU SETTINGS Menu Configuration <IMAGE> 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11 SHARPNESS 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14 BRIGHTNESS 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14 CONTRAST 0, 1, 2, 3, 4, 5, 6, 7 2DNR LEVEL... - Page 33 Note The shutter speed in this exposure parameter is a reference value at 30/60 FPS. -7~+7 <COLORTONE> AUTO R.GAIN -7~+7 G.GAIN -7~+7 B.GAIN LOW, WB-SENSI MIDDLE, HIGH 0~16 MANUAL R.GAIN 0~16 B.GAIN OPWB 2800~6500 STATIC COLOR TEMP SATURA 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14 RUM SCENE INDOOR...
- Page 34 < SYSTEM > PROTOCOL ADDR 1, 2, 3, 4, 5, 6, 7 IR ADDR 1, 2, 3 MOUNT MODE STAND, CEILING PROTOCOL VISCA, PELCO-P, PELCO-D BAUDRATE 2400, 4800, 9600, 38400 VIDEO FORMAT 4K60, 4K50, 4K30, 4K25, 1080P60, 1080P50, 1080P30, 1080P25, 720P60, 720P50 LANGUAGE ENGLISH, CN...
-
Page 35: Menu Explanation
Menu Explanation 1) Press Menu button to enter / exit menu. 2) Press ▲▼ button to select options, it is selected when the font is enlarged, press Enter to enter the menu. 3) Press to change the value. ◀▶ Menu Options Function Descriptions Adjust the sharpness of image and image edge... - Page 36 Mirror The camera image is turned 180 ° horizontally. Flip The camera image flips 180 ° vertically. According to the ambient brightness prototype to Auto Exposure automatically generate exposure parameters and adjust the picture brightness. The user manually sets the exposure parameters and Manual Exposure adjusts the picture brightness.
- Page 37 This operation is performed when the camera is Power UP powered on and doesn't receive the control command. Protocol Address Change camera’s address through menu settings. IR Address Set the IR control address for the camera. The camera image flips 180° vertically and Mount Mode horizontally.
-
Page 38: Technical Specifications
8. TECHNICAL SPECIFICATIONS Camera Image Sensor 1/2.8''4K CMOS, 8.46MP Focal Length f=4.7mm-94mm Iris F1.6～2.8 Optical Zoom Horizontal Viewing 72.5°~6.3° Angle Focus System Auto / Manual, PTZ Trigger, One Push Trigger White Balance Auto, Manual, OPWB, Static Exposure Control Auto, Manual, Shutter Priority, Iris Priority, Bright Priority ≥50dB 2D/3D Support... - Page 39 1 channel USB3.0 1. Support UVC 1.1 2. Image compression H.264/H.265/MJPEG; support 4K/30/25, 1080P60/50/30/25, 720P60/50/30/25, 360P30/25 3G-SDI 1 x 3G-SDI, support 1080P60/50/30/25, 720P60/50 Audio Interface 1 channel LINE IN, 3.5mm audio interface Control Interface 1 channel RS-232 IN, 1 channel RS-232 OUT Power DC12V General...
-
Page 40: Troubleshooting
9. TROUBLESHOOTING Problem Possible Cause Solution Check power supply Power supply failure No action or image Replace power adapter Power adapter damaged after powered on Check & reconnect Power cable connection got loosen Use a shorter cable Power cable is too long No self-testing after Replace power adapter powered on, or with...
Need help?
Do you have a question about the SDC024-B12 and is the answer not in the manual?
Questions and answers