Appendix B: Connections - Mackie 802-VLZ3 Owner's Manual

Appendix B: Connections

"XLR" Connectors
Mackie mixers use 3-pin female "XLR" connectors on
all microphone inputs, with pin 1 wired to the grounded
(earthed) shield, pin 2 wired to the "high" ("hot" or
positive polarity) side of the audio signal and pin 3
wired to the "low" ("cold" or negative polarity) side of
the signal. See Figure A. This is all totally aboveboard
and in full accord with the hallowed standards dictated
by the AES (Audio Engineering Society).
Use a male "XLR"-type connector, usually found on the
nether end of what is called a "mic cable," to connect to
a female XLR jack.
Figure A: XLR Connectors
⁄ " TRS Phone Plugs and Jacks
1
4
"TRS" stands for Tip-Ring-Sleeve, the three
connections available on a "stereo"
phone jack or plug. See Figure B.
RING
Figure B: ⁄ " TRS Plugs
1
4
TRS jacks and plugs are used in several different ap-
plications:
• Balanced mono circuits. When wired as a bal-
anced connector, a 1⁄4" TRS jack or plug is con-
nected tip to signal high (hot), ring to signal
low (cold), and sleeve to ground (earth).
• Stereo Headphones, and rarely, stereo micro-
phones and stereo line connections.
When wired for stereo, a 1⁄4" TRS jack or plug
is connected tip to left, ring to right and sleeve
to ground (earth). Mackie mixers do not
2
SHIELD
HOT
3 1
COLD
SHIELD
1
3
COLD
2
HOT
SHIELD
1
3
COLD
2
HOT
SLEEVE SLEEVE TIP
TIP
TIP
SLEEVE
⁄ " or "balanced"
1
4
SLEEVE SLEEVE RING TIP
TIP
RING
TIP
SLEEVE
directly accept 1-plug-type stereo microphones.
They must be separated into a left cord and a
right cord, which are plugged into the two mic
preamps.
You can cook up your own adapter for a stereo
microphone. "Y" two cables out of a female 1⁄4"
TRS jack to two male XLR plugs, one for the
Right signal and one for the Left.
• Unbalanced Send/Return circuits. When wired
as a send/return "Y" connector, a 1⁄4" TRS jack
or plug is connected tip to signal send (output
from mixer), ring to signal return (input back
into mixer), and sleeve to ground (earth).
⁄ " TS Phone Plugs and Jacks
1
4
"TS" stands for Tip-Sleeve, the two connections avail-
able on a "mono" 1⁄4" phone jack or plug. See Figure C.
Figure C: TS Plug
TS jacks and plugs are used in many different
RING
applications, always unbalanced. The tip is connected to
the audio signal and the sleeve to ground (earth). Some
examples:
• Unbalanced microphones
• Electric guitars and electronic instruments
• Unbalanced line-level connections
RCA Plugs and Jacks
RCA-type plugs (also known as phono plugs) and
jacks are often used in home stereo and video equip-
ment and in many other applications (Figure D). They
are unbalanced and electrically identical to a 1⁄4" TS
phone plug or jack (figure C). Connect the signal to the
center post and the ground (earth) or shield to the sur-
rounding "basket."
SLEEVE
Figure D: RCA Plug
SLEEVE SLEEVE TIP
TIP
TIP
SLEEVE
SLEEVE SLEEVE RING TIP
TIP
RING
TIP
SLEEVE
TIP SLEEVE TIP
Owner's Manual
3