Subscribe to Our Youtube Channel
Related Manuals for SMARTWINGS Helix Dial Remote
Summary of Contents for SMARTWINGS Helix Dial Remote
- Page 1 Programming & Smart Pairing Guide Helix Dial Remote Matter Pergola Louver & LED INS-102-C079 A-01 March 2025...
- Page 2 After completing the pairing process, please stick one copy of the corresponding QR code in the designated field. Keep a backup to facilitate future maintenance and usage, and store the instruction manual properly. Matter LED QR Code Pergola Louver QR Code...
- Page 3 Note Important Safety Instructions...
-
Page 4: Cable Overview
Cable Overview Windproof Shade DC 24V External Power Supply Port Power Supply Port Controller LED Power Programming Button Supply Port Pergola Louver External Power Supply Port... -
Page 5: Table Of Contents
TABLE OF CONTENTS ..........1 1. Remote Overview 2. Helix Dial Remote Programming ......2 .....2 2.1 Pairing Channel & Group Control ............3 2.2 Set Limits ..........4 2.3 Favorite Position .........5 2.4 Pergola Louver Control ..........6 2.5 LED Control ..........7 2.6 Mirror Remotes ........8... -
Page 6: Remote Overview
Remote Overview FRONT Channel Display STOP/LED CHANNEL Battery Light DOWN Percentage/ Dimming Indicator BACK ON/OFF Type-C Technical specification Function instruction One number of screen means one control channel. Press Input Voltage: 3.7V CHANNEL button to change the channel. On the analogy Transmitting Frequency: of this, loose finger when the screen shows the suitable 433.925MHz... -
Page 7: Helix Dial Remote Programming
Helix Dial Remote Programming 2.1 Pairing Channel & Group Control The Helix Dial remote features 8 channels, with Channel 0 serving as the default group control channel to operate all shades under its 8 channels simultaneously. To customize a channel for controlling multiple motors, group pairing can be performed by pairing multiple shades to a specific channel. -
Page 8: Set Limits
Helix Dial Remote Programming 2.2 Set Limits If you press the UP or DOWN button on the remote, controller runs and beeps three times, indicating that the limits are not set. Hold the UP and STOP Controller beeps twice when... -
Page 9: Favorite Position
Helix Dial Remote Programming 2.3 Favorite Position The favorite position allows you to set a custom stopping point between the upper and lower limits (one favorite position per pergola). Press STOP (To Save Position) Press STOP Press UP and CHANNEL... -
Page 10: Pergola Louver Control
Helix Dial Remote Programming 2.4 Pergola Louver Control Percentage Mode To use Percentage Mode, the limits must be set in advance. Open Press and hold the STOP button, then turn the Control Ring counterclockwise to gradually open the louvers. Close... -
Page 11: Led Control
Helix Dial Remote Programming 2.5 LED Control ON/OFF When the louvers are not operating, pressing the STOP button can turn the LED light on/off (default brightness). Percentage Mode Turn the Control Ring counterclockwise, and the LED light will gradually dim until it is completely off. -
Page 12: Mirror Remotes
Helix Dial Remote Programming 2.6 Mirror Remotes Follow the steps below to copy settings from an existing remote to a new one. Select channel that operates the shade Note: Select the channel on the existing remote to be copied, and select the channel on the new remote where the existing channel will be copied. -
Page 13: Reset To Factory Settings
Helix Dial Remote Programming 2.7 Reset to Factory Settings Press and hold the programming button for 14 seconds until controller beeps four times in total. Controller Response BEEP BEEP BEEP BEEP Note: A factory reset means erasing all existing settings on the device. Once you complete the factory reset steps, you will need to re-pair the remote channel and reconfigure the... -
Page 14: Controller P Button Functions
Helix Dial Remote Programming 2.8 Controller P Button Functions If limit is NOT set None None Operational control of Operational control of controller after pairing Controller None controller, run to limit. If limit are set Short Press and limit setting is Stop if running completed first time... -
Page 15: Matter Smart Pairing
Matter Smart Pairing 3.1 Work With Matter Over Thread... - Page 16 Matter Smart Pairing...
-
Page 17: Pergola Louver Network Pairing Mode
Matter Smart Pairing 3.2 Pergola Louver Network Pairing Mode Method One: Press and hold the P button on the controller head for 6 seconds until the controller beeps twice, then release the button. The controller will beep twice again, and the LED will stay on, indicating that pergola louver network pairing mode has been activated. -
Page 18: Led Network Pairing Mode
Matter Smart Pairing 3.3 LED Network Pairing Mode Method One: Press and hold the P button on the controller head for 10 seconds until the controller beeps thrice, then release the button. The controller will beep twice again, and the LED will stay on, indicating that LED network pairing mode has been activated.
Need help?
Do you have a question about the Helix Dial Remote and is the answer not in the manual?
Questions and answers