Related Manuals for hernest Valborg HEFTSB-8095
Summary of Contents for hernest Valborg HEFTSB-8095
- Page 1 HEFTSB-8095 HEFTSB-8113 HEFTSB-8098 HEFTSB-8112 GZWH Assembly Instructions & Care Guide Illustrations in this guide are for reference only and may differ slightly from the actual product.
-
Page 2: Table Of Contents
CONTENT Before You Start Overview Caution Material Specifications Installation Guide Exploded Views Component Parts Hardware Assembly Directions 05-14 Troubleshoot 15-17 Usage and Maintenance Use and Care Other Help Center... -
Page 3: Before You Start
4. Place all hardware on a soft surface for easy identification. 5. The seller is not responsible for any damage or injury caused by improper assembly or use. 6. If you need further assistance, please contact us through service@hernest.com Caution 1. -
Page 4: Installation Guide
3. Pay attention to tightening the screw rod 4. Installation plate 5. Align the arrow of the eccentric 6. Pay attention to aligning the component with the screw rod arrow of the eccentric part with the screw rod HERNEST I 02... -
Page 5: Component Parts
Component Parts HERNEST I 03... -
Page 6: Hardware
Do not over-tighten screws or use power tools, as this may damage the product. Tools You May Need Persons and Time Needed For Assembly *You might need a screwdriver (+/-) to complete this assembly. People Time Difficulty 2 hours HERNEST I 04... -
Page 7: Assembly Directions
Assembly Directions Step 1 A x7 S x1 Step 2 B x4 HERNEST I 05... - Page 8 Step 3 A x6 B x9 L x2 E x6 Step 4 A x7 B x3 HERNEST I 06...
- Page 9 Step 5 A x13 Step 6 B x9 F x6 HERNEST I 07...
- Page 10 Step 7 B x8 Step 8 A x13 HERNEST I 08...
- Page 11 Step 9 B x13 I x6 Step 10 D x16 HERNEST I 09...
- Page 12 Step 11 O x16 G x8 Step 12 E x16 J x2 N x4 HERNEST I 10...
- Page 13 Step 13 E x16 J x2 N x4 Step 14 H x16 HERNEST I 11...
- Page 14 Step 15 C x4 J x2 N x4 Step 16 O x16 P x2 Q x2 HERNEST I 12...
- Page 15 Step 17 O x16 Step 18 HERNEST I 13...
- Page 16 Finished! Fantastic, we're nearly there! Please carry out the following checks: 1. Have you tightened all the screws? 2. Are the levelers aligned with and making contact with the ground? 3. Have you installed the anti-tipping kit? HERNEST I 14...
-
Page 17: Troubleshoot
Please sightly loosen all screws and adjust the bards. Because the diameter of the holes on the pipes 23 mm lager than that of bots, the position of the boards can be adjusted. If it is still doesn't work after adjustment, please contact us for more solutions. HERNEST I 15... - Page 18 The hinges shown in the image. The door panel can be moved door panel can be moved door panel can be moved front-back. up-down. left-right. Adjustment range: 4mm Adjustment range: 4mm Adjustment range: 3mm HERNEST I 16...
- Page 19 Door panel is not Door straight panel Side panel Adjust the Finished door hinges Door panel HERNEST I 17 The gap between door panels is too large Door Adjust the panel Finished door hinges Door Side panel panel...
-
Page 20: Usage And Maintenance
Please educate children to stay away from the glass sharp corners of the furniture. When opening and closing doors or drawers, handle them gently and check the screws regularly to tighten them. Use a soft dry cloth to dust, a slightly damp cloth to clean the surface, avoid abrasive cleaners. HERNEST I 18... -
Page 21: Help Center
Treat your furniture with care and follow the maintenance guidelines. In return, your furniture will provide you with lasting comfort and support. For any additional inquiries or assistance, please do not hesitate to contact us at https://www.hernest.com/ help Inquiry Assembly issue Missing parts Returns&Refunds...
Need help?
Do you have a question about the Valborg HEFTSB-8095 and is the answer not in the manual?
Questions and answers